74.90EUR

DUPLEX 2.4EX MSpeed PITOT <300 Km/h
[JETIPITOT]

DUPLEX 2.4EX MSpeed PITOT <300 Km/h

MSPEED EX is a sensor which measures the speed of a flying model through the air to provide the indicated airspeed (IAS). The reporting of airspeed can be very instructive with regard to the control of a flying model, for example allowing the pilot to determine the model´s stall speed and set an alarm to indicate when the model falls below this speed. Another function of the sensor is to allow the pilot to set a desired speed and a step above or below this speed at which an acoustic signal should be sounded by the transmitter module. To facilitate easier reading of the indicated airspeed, a bar graph is displayed, marking the appropriate configured steps. The measurement of airspeed is based on the principle of change in dynamic pressure, measured by a Pitot tube, which is connected by silicon tubing. With the help of the wireless Duplex system, this sensor information can be reported to the pilot in realtime, allowing immediate feedback in airspeed changes and a deviations from the configured steps.

Weight [g] 21
Dimensions [mm] 22 x 25 x 13
Operational temperature [°C] 0 ... 85
Supply Voltage [V] 3,5 - 8,4
Average Current [mA] 10
max. Speed ~300km/h

under request

Reviews

Quick Find

Shopping Cart

2 x	Motor EME 35 cc with electric starter
2 x	CDI EME 120cc
1 x	EME ignition free wheel
2 x	Motor EME 70 cc with autostarter
2 x	Motor EME 60 cc with electric starter
3 x	CDI EME 55/60 cc
2 x	Pitts Mufflers EME 55/60 cc
2 x	Motor EME 70 cc
2 x	Motor EME 60 cc
1 x
1 x	2000A 12V Lithium Jump Starter with 150PSI Air inflator
2 x	Servo NARO Max Std
1 x	Motor Moki S 250 cc 5 cyl with autostarter
2 x	Motor EME 35 cc
2 x	Propeller pad and output shaft EME 55/60 cc
1 x	Cylinder EME 35 cc
1 x	Propeller hub EME 60cc
1 x	Pick up EME 55/60 cc
1 x	Bearings for motor HACKER C50
2 x	Ø 38 mm fiberglass motor-holder for electric motors
2 x	Frontal support Speed 600
1 x	Ø 40 mm fiberglass motor-holder for electric motors
1 x	A60 Motor Mount Alu complete set
1 x	Metalic motor holder for class 550-600
1 x	Pitts Mufflers EME 35 cc
1 x	VALACH Motors VM 70 S1-4T
1 x	Selfstarr EME35
1 x	Piston ring EME 35cc
1 x	Sandwich carbon + poplar 4mm + carbon 480x290 mm
1 x	Propeller 9x7 SlowFlyer
1 x	Servo-V-Limiter 5.2V
1 x	Switch magnet for gas cap and magnet switch actuators
1 x	DPSI OCP Overload protection
1 x	DPSI RV Mini 6 Magic with Gas-Cap switch
1 x	Size "M" motor holder for class 600
1 x	Ø 28 mm fiberglass motor-holder for electric motors
1 x	Central support Speed 600
1 x	Rotor blade 3Bl Scale 1050R
1 x	Prop Saver for AXI 22xx/xx
1 x	DEMON CORTEXpro
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	DUPLEX 2.4EX Central Box 210
1 x	Adapter 3,0 mm M6
1 x	AXI 2212/26 V2
1 x	Hovercraft sailcloth
1 x	Piston EME 35cc
1 x	DPSI V-Match
1 x	Selfstarr DLE55, EME55/60, DLA56, SE 55
1 x	DPSI Micro - RCS
1 x	DPSI Micro MPS
1 x	Motor mount for 1200 mm models
1 x	Central support Speed 280
1 x	10 mm gas motor standoff
1 x
1 x	Cooler motor type 400
1 x
1 x	Receiver bed (Blue)
1 x	AXI Cooler 22xx
1 x	AXI 2212/20 V2
1 x	Winter-Glove DS tx
1 x	Threaded coupler ALU Left M3 Ø 4 (2 uds)
1 x	DUPLEX 2.4EX MUI 150 Sensor
1 x	3 mm Short Prop Adapter M5
1 x	Hand Pads for Tray JETI
1 x	AXI 2820/12 CYCLONE

15,582.28EUR