184.00EUR

ESC KAVAN PRO-160HV Opto 160 Amp
[KAV3231055]

Programmable brushless ESC for big high-voltage (HV) aircraft models. Continuous current 160A (peak 200A), 6–14 LiPo cells power, OPTO (galvanically isolated control and power electronics). Weight: 221g; dimensions: 110x50x33mm. Programmable microprocessor ESC for brushless, sensorless AC motors ("brushless, sensorless") for hobby and sport aircraft models with LiPo/Li-ion/LiFe battery power supply. It uses advanced optimized control technology to significantly improve throttle response and power stage control efficiency. The ESC design takes into account the high long-term load capacity and durability required in giant models when powered by a high cell count battery. The power section of the ESC is galvanically isolated from the control electronics to provide high immunity to interference at high operating currents and high supply voltages. The ESC is not equipped with a BEC for the receiver and servos. A special KAVAN PRO LED programming card, which is supplied separately, is used to easily set up the ESC.
DESCRIPTION AND FUNCTIONS OF THE ESC
The ESC features a high-performance 32-bit ARM M4 microprocessor with a clock frequency of up to 72 MHz; it is compatible with most brushless motors.
Suitable for the vast majority of aircraft brushless motors powered by 6-14S LiPo/Li-ion/LiFe batteries.
Special power stabilizer for microprocessor for high interference immunity and reduced risk of loss of control.
Optimized control technology significantly improves throttle response and power stage control efficiency and reeduces ESC temperature.
Galvanically isolated power part by optoelectronic component.
Normal/Soft/Very Soft start-up modes are suitable for normal propeller aircraft and models with EDF.
Easy programming and setup using the transmitter or the KAVAN PRO LED programming card.
A special programming cable for connecting the ESC to the LED programming card allows the user to program the ESC anytime and anywhere (see the KAVAN PRO LED programming card manual for details).
Normal/Proportional/Reversal brake modes (especially reversal mode) can effectively shorten the range after landing.
A number of protection functions: start-up protection, thermal protection of the ESC, thermal protection of the capacitors, overload protection, overcurrent protection, abnormal supply voltage protection and control signal loss protection effectively extend the life of the ESC.
Calibrate the throttle range to perfectly match the control signal from your RC kit.

PROGRAMMABLE FUNCTIONS
Brake Type Brake off, normal brake (with braking intensity adjustable in 7 levels), proportional brake (controlled by the throttle control: 0-20% of throttle control deflection corresponds to 100-0% brake, 20-100% of control deflection corresponds to 0-100% throttle), reversing (allows to switch on the reversing of the motor running by another channel with a switch).
Brake Force: The braking intensity is adjustable from Level 1 to Level 7 for "Normal Brake" mode.
Cutoff type: Soft Cutoff: the contESCroller will gradually reduce power to 50% of full power within 3 seconds after voltage protection is activated. Hard Cutoff.
Number of LiPo cells: We recommend setting manually for 100% reliable voltage protection function. The ESC will automatically calculate the number of cells of the connected battery according to the "3.7 V per cell" rule if you select automatic detection.
Cutoff Voltage: The threshold level of the voltage protection is adjustable from 2.8 to 3.8 V/cell; the protection can also be switched off completely.
Start-up Mode: Normal start-up (instant start-up), Soft start-up (with slow start for motors with large propellers, gearbox or smaller EDF), Very soft start-up (with very slow start for motors with large propellers, gearbox or EDF from 90 mm).
Timming: Adjustable from 0-30°.
Motor direction: CW/CCW
DEO Freewheeling: This feature can be turned on or off; it can provide better linearity or smoother throttle response.

PROTECTIVE FUNCTIONS OF THE ESC
Start-up protection The ESC measures the motor speed during start-up. If the speed stops increasing or the increase is not stable, the ESC evaluates this as an incorrect start-up. If the throttle is at less than 15% at this point, the ESC will automatically attempt to restart the motor; if the throttle is at more than 15%, you must pull the throttle control all the way down to restart the motor.
Thermal protection of the ESC: The motor will "stall" if the ESC temperature exceeds 110°C, indicating that thermal protection has been activated. If the throttle control is pulled back below 60% at that point, the "stutter" will disappear and the ESC will deliver power appropriate to the throttle position. If you move the throttle above 60%, the "stutter" will reappear. The temperature of the ESC must not exceed 70°C when switching on, otherwise the engine cannot be started.
Signal loss protection The ESC will immediately shut down the motor if the signal is absent for 0.25 s to prevent even more damage and risks from a rapidly rotating rotor or propeller. Once a normal signal is received, the ESC resumes normal operation.
Overload protection The ESC switches off the motor or restarts automatically when its load suddenly increases to a very high value.
Overcurrent protection: The ESC immediately switches off the motor if the peak current draw exceeds the maximum permitted value; it then resumes normal operation. If the current draw still exceeds the maximum permitted value, the motor is switched off completely.
NOTE:The throttle cable of the ESC is the two-wire lead (white + black wire), the programming cable is the 3-wire lead (white + red + black wire). Connect ONLY the throttle cable to your receiver.
Tip: When the first time the regulator is switched on, first calibrate the throttle range according to the instructions. Only then can the ESC be used and other parameters set using the transmitter or the KAVAN PRO LED programming card.
Use: Airplane,helicopter
Type: brushless ; Current rate [A]: 160 ; Max. peak current [A]: 200 ; LiXX cells: 6 - 14 ; Lenght [mm]: 110 ; Width [mm]: 50 ; Height [mm]: 33 ; Weight [g]: 221 ; Regulation type: one-way ; Brzda: Yes ; Sensor input: No ; Programmable: Yes Used for Aeroplane,Helicopter Type AC Constant current [A] 160
Max. peak current [A] 200
LiXX cells 6 - 14
Length [mm] 110
Width [mm] 50
Height [mm] 33
Weight [g] 221
Control one-way
Brake Yes
Sensor imputs No
Programmable Yes

under request

Reviews

Quick Find

Shopping Cart

1 x	Motor RACE 20 Navy 12v
2 x	Jodel D.9 BeBe 2.400 mm Kit
1 x	IKARUS plane
1 x	3,2 mm Prop Adapter M8
1 x	Prop Shaft Adapter 5 mm/M8 "long"
2 x	Dumper propeller 6/8 mm
1 x	Prop Shaft Adapter 5 mm "long"
1 x	5 mm Prop Adapter M8
1 x	3,2 mm Prop Adapter M6
2 x	La Capitania di Venetia accesories
1 x	5 mm Prop Adapter M8
1 x	Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
1 x	Profile ABS Square 3 x 1000 mm
2 x	Circlick securite
1 x	Brass rod Ø 1.0 mm x 1000 mm
1 x	Oracover Verde 2 m
1 x	Cable silicona macho batt. receptor 30 cm (Graupner)
1 x	Brass control horn M4 short for wire (4 pcs)
1 x	Futaba Female 40 cm extension
1 x	Blue smoke canister 140 g
1 x	Fast'n EZ-CA-Hinge (12 uds)
1 x	Initior Transmitter FTX2 Wireless
1 x	Brass control horn M4 short for wire (10pcs)
1 x	18 mm reinforced hinge
2 x	Premium servo extension 25cm
2 x	servo adapter lead, JST-SH socket - JR male Pin, for GR-12SH+HoT
1 x	Threaded coupler ALU M2,5 Ø 4 (2 uds)
1 x	Oracover Yellow CADMIO 10 m
1 x	Straightened rod Ø 0.5 mm x 1000 mm
1 x	Ferrita 14x8x5.5 mm
1 x	L-Connector 1.5 mm x 1000 mm
1 x	Straightened rod Ø 14.0 mm x 1000 mm
1 x	Flap hinge 33x9 mm (6 pcs)
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	Horn for flap control (1 pcs)
1 x	Brass hexagonal rod Ø 4 mm x 1000 mm
1 x	Oracover Azul 2 m
1 x	Electric spoiler 440 mm (2 pcs)
1 x	Long pinned hinge (6 uds)
1 x	Glider STROLCH
1 x	Straightened threaded rod M2-1m
1 x	Oracover ROYAL RED 2m
1 x	Ventus 1:4 set of instruments
1 x	1/6 Pilot "Garry"
1 x	Carb Carrier, red DA-150L/170
1 x	Piston ring for DA-85 and DA-170
1 x	L ELBOW 90º ø 25 mm
1 x	Piston ring for DA-150
1 x	Reed valve cage with petals for DA 100/150
1 x	Prop washer for DA-85, DA-100, DA-100L, DA-120
2 x	B4-0 rocket charges (6 pcs)
1 x	Ply-Span 450x600/13g Blue
1 x	Horn with ball 55x40
1 x	PCARD Wireless System
1 x	Oracover CARBON Metalic 1 m
1 x	Cross Connector 4.0 mm x 1000 mm
1 x	Oracover Yellow CUB 10 m
1 x	6 mm blue aluminium threaded horn with patella
1 x	U Profile ABS 5,0x10,0x1000 mm
1 x	RH long aluminium horn (2pcs)
1 x	Initior Receiver FRX2 Wireless
1 x	Streamline Stainless Steel Tubing 6.3x3.5x1000 mm
1 x	Horn 20x28,5 mm (2 pcs)
2 x	0,14 mm PVC servo wire extension, ZH micro conector.
1 x	Threaded coupler ALU Left M2,5 Ø 3 (2 uds)
1 x	White smoke bombs AX-60 (5 pcs)
1 x	Actuador lineal HLS12-100210-7.4v
1 x	X-RAY Micro QR (Rudder)
1 x	Threaded coupler ALU M2 Ø 4 (2 uds)
1 x	Straightened rod Ø 1.0 mm x 1000 mm
1 x	1/6 Pilot "Buddy"
1 x	Oracover Black 2 m
1 x	Towing hook <3m
1 x	200 mm extensión servo HITEC/JR
1 x	Long pinned hinge (12 uds)
1 x	Nylon hinge 20x15x0,3 (10 pcs)
1 x	AX-60 starters (5 pcs)
1 x	48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
1 x	Gates hinge
1 x	Civilian pilot "Pamela" size 9cm (Slimline)
1 x	1/12 Pilot "Cougar"
1 x	Yellow smoke canister 100 g
1 x	Premium servo extension 100cm
2 x	ORACOVER Fluor red (2 m)
2 x	Streamline Stainless Steel Tubing 15.5x8.5x1000 mm
1 x	Threaded coupler ALU Left M3 Ø 4 (2 uds)
1 x	Pilot "Dick" Legends Series (Slimline)
1 x	Gates hinge aluminium (1 pcs)
1 x	SlowFlyer control horn (3 pcs)
2 x	Extension S-Bus 1-2 silicon 120 cm FUTABA
1 x	Smoke set "S"
1 x	Gates hinge 30x16 mm (2 pcs)
1 x	ABS angle 5,0x5,0x1000 mm
1 x	Extension lead 15 cm Multiplex
2 x	Streamline Stainless Steel Tubing 17.8x12.4x1000 mm
1 x	White smoke bombs AX-18 (5 pcs)
1 x	Extension silicon 30 cm male (Futaba)
1 x	Yellow smoke canister 65 g
1 x	1/7 Pilot "Japanese"
1 x	6 mm aluminium horn with patella
1 x	Gates hinge black 30x16 mm (2 pcs)
1 x	1/12 Pilot "Fighter"
1 x	Micro flex hinge (12 uds)
1 x	Zurich Sport Sunglasse Dark Sensity BROWN Glasses
1 x	ABS Strip 1.5x4.0x1000 mm
1 x	Lock washer 2.7 mm (20 pcs)
2 x	Ball Link M2 with Ball and Hardware, 10 pcs
1 x	Clevis plastico I=44 mm / hole 3mm / pin 2 (2 pcs)
1 x	M3 black washers (4 pcs)
1 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	Glases Nimbus
1 x	Carbon fiber rod 16 mm x 1000 mm
1 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	Squared carbon wing joinner 5x5x220 mm
3 x	Aluminium wide washer M4 Black (4 pcs)
1 x	Field folding model stand SebArt
1 x	Strip 2,5x1,25x330 mm
2 x	Aluminium wide washer M3 gold (4 pcs)
1 x	Quicklock washer 1 mm (10 pcs)
1 x	Round Rod 3,0x1000 mm
1 x	50 mm aluminium spinner (Kavan)
1 x	Ciano KAVAN Thick 20g
1 x	50 mm gas motor standoff
1 x	Brazo servo KAVAN doble aluminio 25T - 2.5" M3
1 x	Crawler GRE-24 RTR 1:24 Arena
1 x	Spark Ceramic JETCENTRAL
1 x	Power Pack SE Series JETCENTRAL
1 x	Battery RX JETI LiIon RB 2600 7.2v
2 x	DUPLEX 2.4EX Central Box 210
2 x	DUPLEX 2.4EX MULi 6s M
1 x	L ELBOW DA-120 long (2 pcs)
1 x	Concave-Convex sandpaper file 13 mm
1 x	Combustible Glow "KAVAN" air/heli 15% nitro
1 x	Ciano KAVAN Super Thin 20g
1 x	5 mm gas motor standoff
2 x	Ciano KAVAN Thin 20g
2 x	12 mm floating pad (49 pcs)
1 x	25 mm Sandpaper file
1 x	Combo KAVAN PRO 3536-1000 + RAY 40 SB
1 x	Ciano KAVAN Medium 20g
2 x	AL Axle Shaft 4.0x16 mm (2 uds)
2 x
1 x	60 mm aluminium spinner (Kavan)
1 x	35 mm gas motor standoff
1 x	10 mm gas motor standoff
2 x	Aluminium wide washer M4 Blue (4 pcs)
2 x	Aluminium red ball links M3 V1 (10 pcs)
2 x	Aluminium cap bolt washer M4 red (8 pcs)
1 x	Cable coupler M3 (10 uds)
1 x	Adaptadores carga 6s JST-XH
1 x	Aluminium cap bolt washer M3 red (8 pcs)
1 x	10 mm aluminium spinner (Kavan)
1 x	150 mm inflatable superlight deluxe wheel (2 pcs)
1 x	55 mm aluminium spinner (Kavan)
1 x	Blade holder metal LAMA
1 x	25 mm gas motor standoff
2 x	10 mm floating pad (72 pcs)
1 x	Conector MR-60 (pareja)
1 x	A/C quality beech plywood 600x300x0.8 mm
1 x	Antenna Hole Cap V1 (Silver)
3 x	BETA 1400 ARF Red
1 x	Aluminium wide washer M3 red (4 pcs)
2 x
1 x	Aluminium ignition bad (blue)
1 x	aluminium servo arm V1-JR 1,0 inch M2
1 x	Birch plywood plate 600x300x1.5 mm
1 x	Ball Bearing Oil 25 ml
1 x	Cable coupler M2 (10 uds)
2 x	Aluminium cap bolt washer M3 green (8 pcs)
1 x	Aluminium cap bolt washer M3 black (8 pcs)
1 x	20 mm gas motor standoff
1 x	Aluminium wide washer M4 Gold (4 pcs)
1 x	Aluminium wide washer M4 Red (4 pcs)
1 x	20x1000 mm Ring Strap Back To Back
1 x	aluminium servo arm V2-JR 2,0 inch M3
1 x	40 mm gas motor standoff
1 x	15 mm gas motor standoff
2 x	Aluminium cap bolt washer M4 blue (8 pcs)
1 x	Debonder CA 20g
2 x	11 mm Rubber pads (14 pcs)
1 x	BETA 1400 RTF Red
2 x	Aluminium wide washer M3 blue (4 pcs)
1 x	Colador RABBIT
1 x	HDT Jet Central
1 x	JETCENTRAL ECU LIFE BATTERY 3800 MAH
2 x	AddCAP 10AS capacitors
1 x	PPM to Jack link - Tx Black (mono) DC/DS Tx DUPLEX 2,4EX
1 x	OPTIC 8 opto Rx-servo insulation
1 x	DUPLEX 2,4EX Brackets for Transmitter DC/DS
1 x	DSM 10 Dual Switch Mixer
1 x	Pilatus PC-21 + LG.2100 mm RED/WHITE (SebArt)
1 x	DC-3 Douglas (White/Blue) 1800 mm
1 x	DUPLEX 2.4EX MU 3 Sensor
1 x	DUPLEX 2.4EX MUI 75
1 x	YAK-23 "FLORA" (RBC Kits)
1 x	Esc MasterSPIN 99 Pro OPTO
1 x	KATANA DV 20 1470 mm
1 x	Master MEZON 120
1 x	Esc MasterBasic 40SB
1 x	Equipment set XL
1 x	Sun Cover PC 21 XXL (JMB Jets)
1 x	Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
1 x	Spinner propeller pleg. 30 mm / 4,0 mm
1 x	Spinner plastic white propeller pleg. 30 mm / 3,2
1 x	25,0 mm 3-BL M4 hydro-propeller (rigth hydropropeller)
1 x	Spare spinner 65 mm 3-Bl
1 x	Spinner black 36-38 mm
1 x	Cabestrante plastico 5x6 mm (10 pcs)
1 x	Propeller POWER-PROP 10x7 Izda
3 x	Futaba Female 40 cm extension
1 x	Extension silicon 100 cm (Graupner)
1 x	Extension silicon 10 cm (Futaba)
1 x	Propeller electric carbon 9.5x5
1 x	Micro control horn T2 Ø 1
1 x	Metalic joint for DA-150 cilinder/elbow
1 x	Aluminium-screw, M5x20mm Red
1 x	Spring Clip 25 mm teflon tube
1 x	PC-21 PILATUS Electric retract system
1 x	DH82 Tiger Moth ARC Scale 1:3.3
1 x	Power Box GPS Sensor III
1 x	PowerBox OLED display
1 x	2 piece mounting frame Battery 3200 / 4000
1 x	19 mm 2:1 black termoretract tube
1 x	Propeller FALCON 32,5x11 PUSHER Carbono
1 x	76 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	Spinner propeller pleg. 38 mm / 6 mm
1 x	Spinner fold propeller 50 mm (white spare spinner)
1 x	Barandilla Ms 10x250 mm (2 pcs)
1 x	Anchor of tow Met. 60 mm
1 x	Chigre de amarre Scale 1:32
1 x	White smoke bombs AX-9 (10 pcs)
1 x	Yellow smoke bombs AX-60 (5 pcs)
1 x	Spinner propeller pleg. 45 mm / 6 mm
1 x	28 mm turnbuckle
1 x	Doppelpoller 17 mm (6 uds)
1 x	16x10 tree blades propeller Master Airscrew
1 x	Pump 12 V
1 x	14 mm portholes (10 pcs)
1 x	3.17 mm Prop Adapter CN-Spinner
1 x	Antiaircraft gun 10.5 cm (2 pcs)
1 x	29,0 mm propeller (left propeller)
1 x	10x7 tree blades propeller
1 x	METEOR 1.000 mm kit
1 x	Spinner 3BL propeller pleg. 36 mm / 4,0 mm
1 x	Aero-Master Wings (Aero-naut)
1 x	5 mm Prop Adapter M6
1 x	Premium servo extension 75cm
1 x	Cable S.BUS 3 salidas 100 mm
1 x	Extension silicon 25 cm (Futaba)
1 x	Propeller electric carbon 6x5
1 x	Futaba male 40 cm extension
1 x	Extension silicon 50 cm (Graupner)
1 x	Extension PVC 150 cm (Graupner)
1 x	Xoar Electric Beechwood Prop 22x10
1 x	Premium servo extension 50cm
1 x	Cable silicona female batt. receptor 30 cm (Futaba)
1 x	Streamline Stainless Steel Tubing 12.3x7.7x1000 mm
1 x	Extension silicon 35 cm (Futaba)
1 x	Sistema LDS - Ø12 mm servos Ø 5/24 spline 95º (MKS) pitch 6 mm
1 x	Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 4 mm
1 x	Combustible Glow "KAVAN" air/heli 5% nitro
1 x	Short adjustable control horn 3x24
1 x	BULLIT Wing 840 mm
1 x	Cabel "Y" 30 cm (graupner)
1 x	Cable S.BUS 3 salidas 300 mm
1 x	Sistema LDS - Ø12 mm servos Ø 5/24 spline 95º (MKS) pitch 7 mm
1 x	Extension silicon 100 cm (Futaba)
1 x	Exhaust gasket DA-60/120
1 x	Reed valve petal for DA 35/50R/100l carburator
1 x	Gasket for motor DA 50-R
1 x	Aluminium-screw, M5x16mm Red
1 x	Propeller plate for DA-120 / DA-170 / DA-150 New Version
1 x	O-Ring for Carburetor screw DA85, DA-100L, DA-120
1 x	Cer clip DA-50R, DA-60 DA-100 DA-100L DA-120, 1 piece
1 x	Cylinder Gasket set for DA-60 / DA-120
1 x	PARTENAVIA 2020 mm ARF with Flaps
1 x	JU87B STUKA 60cc ARF - BlackHorse
1 x	BU 131 Jugmann ARC
1 x	DH82 Tiger Moth Scale 1:3.3 Panel Instrum. trasero
1 x	CARBON CUB FX-3 100-200CC ARF, 165" - 4200 mm (Hangar9)
1 x	PILATUS PC-6 Turbo Porter 33% 5.290 mm
1 x	PowerBox Evo
1 x	JEEMO Kit ARF Basic (2 color Carbon finish) XTRALIGHT
1 x	FIALA Propeller 19x12 Electric
1 x	Wheel collar 3 mm Ø (4 uds)
1 x	100 Newtons FEMA absorber
1 x	400 Newtons FEMA absorber
1 x	RF9 Flight Simulator with Spektrum Controller
1 x	Transmitter Stick Ends V2 Red - M3 (2 pcs)
1 x	Fuel dot blue
1 x	Rudder 2_Tray 3~3.5 inch
1 x	Fuel line plugs (Red)
1 x	Rudder 2_Tray 4.5~5 inch
1 x	DUPLEX 2.4EX Expander E4
1 x	DUPLEX 2,4GHz MRPM-AC EX
1 x	Refueling Cup V2 Red
1 x	Switch Cap M (red)
1 x	Rubber bushing with bracket "A" type (2 pcs)
1 x	TX-Tray V1 (L) (Red)
1 x	Transmitter Balancer SPK DX-8
1 x	Servo Arm 25T M3 KAVAN 6.5 / 19.6 mm
1 x	Refueling kit for Cap "Red"
1 x	M3 Maxi ball link (2 uds)
1 x	3,2x1000 mm 2:1 red termoretract tube
1 x	5 LiPo XH>EH adapter
1 x	Carburetorgasket DA-85, DA-100, DA-100L and DA-120
1 x	Suction funnel for carburetor DA70- MVVW 190cc (red)
1 x	FuelTank Cap (blue)
1 x	Blue aluminium servo arm V1-Hitec 1,5" inch M3
1 x	M3-M4 rubber washer (8 pcs)
1 x	Transmitter Stick Ends V5 Red - M4 JR/DX7
1 x	DUPLEX 2.4EX Expander E2
1 x	DUPLEX 2.4EX MFlow2 Gas 800
1 x	DUPLEX 2.4 EX MBar
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	One touch canopy lock
1 x	Wing bolts M6 Steel screw Blue (2 pcs)
1 x	TX-Tray V1 (L) (Black)
1 x	Landing gear axle 4x21 4 mm (2 uds)
1 x	45 mm gas motor standoff
1 x	Aluminium cap bolt washer M3 blue (8 pcs)
1 x	White aluminium 230 mm landing gear
1 x	Combo KAVAN C3536-1250 + KAVANA R50SB +
1 x	Round Rod 1.0x3.5 cm
1 x	Lipo KAVAN 5000 mAh 11.1v 40/80C
1 x	3 copper lacquer wire Ø0,2 mm (1 m)
1 x	2,5x60 mm allen screwdriver
1 x	Transmitter Stick Ends V3 Red - M3 (2 pcs)
1 x	Transmitter Stick Ends V5 Blue - M4 JR/DX7
1 x	Fully Threaded Steel Rod Duralumin 120 mm M3 (2 pcs)
1 x	Fuel dot Gold color
1 x	Marker ties (20 pcs)
1 x	TX Tray V1 Hand Rests only
1 x	Blue aluminium servo arm V1-Hitec 1,0" inch M2
1 x	Red aluminium servo arm V1-Futaba 15 mm iM2
1 x	Red aluminium servo arm V1-Futaba 17 mm M2
1 x	Transmitter Stick Ends V5 Blue - M3 Futaba/Hitec/Spektrum DX8 (2
1 x	Fuel dot V3 (Blue)
1 x	Fuel dot V3 (Black)
1 x	FuelTank Cap (red)
1 x	Receiver bed (Blue)
1 x	Aluminium cap bolt washer M4 green (8 pcs)
1 x	Electric starter BEE (old)
1 x	Neck strap JETI DC
1 x	DUPLEX USBa USB-Adapter for Jeti Duplex Items
1 x	Teacher / Student Cable
1 x	DUPLEX 2.4 EX MVario2
1 x	Battery RX JETI LiIon RB 6200 7.2v
1 x	DUPLEX 2.4EX Central Box 220
1 x	DUPLEX 2,4GHz MRPM EX
1 x	DUPLEX 2.4EX MAlti (Rev.2)
1 x	Connectors banna oro 3,5 mm (M/F)
1 x	DUPLEX 2.4EX Central Box 220 + 2x Rsat2
1 x	Floating M3 washer pad (36 pcs)
1 x	Transmitter Balancer HITEC Aurora 9, JR and Spectrum (blue)
1 x	Transmitter Balancer Futaba FF9-DX7-JR-Hitec
1 x	Deposito SECRAFT V2 1000 ml Gas
1 x	Switch Cap M (silver)
1 x	T- Fittings red color (2pcs)
1 x	Refueling Cup V2 Blue
1 x	Transmitter Balancer Futaba V
1 x	Neck strap Double V2
1 x	Wing bolts M6 Steel screw Red (2 pcs)
1 x	Wing bolts M3 Steel screw blue (2 pcs)
1 x	15 mm floating pad (30 pcs)
1 x	Fuel Fittings-Gold
1 x	Transmitter Balancer Futaba T-10CG
1 x	Rubber bushing with bracket "B" type (2 pcs)
1 x	Refueling Cap V3 Black
1 x	Floating M4 washer pad (36 pcs)
1 x	T- Fittings blue color (2pcs)
1 x	SE-M Filter
1 x	Switch Cap M (black)
1 x	Servo GO-1023MG 7.0 kg.cm 0.09s/60º
1 x	Microbalon filler for CA glues. Packaging bottle 20g
1 x	wire tensioner (black)
1 x	Secraft Fuel system v2, red color
1 x	Wheel 38 mm V2
1 x	Threaded coupler M2 (10 pcs)

27,769.19EUR