184.00EUR

ESC KAVAN PRO-160HV Opto 160 Amp
[KAV3231055]


ESC KAVAN PRO-160HV Opto 160 Amp
Programmable brushless ESC for big high-voltage (HV) aircraft models. Continuous current 160A (peak 200A), 6–14 LiPo cells power, OPTO (galvanically isolated control and power electronics). Weight: 221g; dimensions: 110x50x33mm. Programmable microprocessor ESC for brushless, sensorless AC motors ("brushless, sensorless") for hobby and sport aircraft models with LiPo/Li-ion/LiFe battery power supply. It uses advanced optimized control technology to significantly improve throttle response and power stage control efficiency. The ESC design takes into account the high long-term load capacity and durability required in giant models when powered by a high cell count battery. The power section of the ESC is galvanically isolated from the control electronics to provide high immunity to interference at high operating currents and high supply voltages. The ESC is not equipped with a BEC for the receiver and servos. A special KAVAN PRO LED programming card, which is supplied separately, is used to easily set up the ESC.
DESCRIPTION AND FUNCTIONS OF THE ESC
The ESC features a high-performance 32-bit ARM M4 microprocessor with a clock frequency of up to 72 MHz; it is compatible with most brushless motors.
Suitable for the vast majority of aircraft brushless motors powered by 6-14S LiPo/Li-ion/LiFe batteries.
Special power stabilizer for microprocessor for high interference immunity and reduced risk of loss of control.
Optimized control technology significantly improves throttle response and power stage control efficiency and reeduces ESC temperature.
Galvanically isolated power part by optoelectronic component.
Normal/Soft/Very Soft start-up modes are suitable for normal propeller aircraft and models with EDF.
Easy programming and setup using the transmitter or the KAVAN PRO LED programming card.
A special programming cable for connecting the ESC to the LED programming card allows the user to program the ESC anytime and anywhere (see the KAVAN PRO LED programming card manual for details).
Normal/Proportional/Reversal brake modes (especially reversal mode) can effectively shorten the range after landing.
A number of protection functions: start-up protection, thermal protection of the ESC, thermal protection of the capacitors, overload protection, overcurrent protection, abnormal supply voltage protection and control signal loss protection effectively extend the life of the ESC.
Calibrate the throttle range to perfectly match the control signal from your RC kit.

PROGRAMMABLE FUNCTIONS
Brake Type Brake off, normal brake (with braking intensity adjustable in 7 levels), proportional brake (controlled by the throttle control: 0-20% of throttle control deflection corresponds to 100-0% brake, 20-100% of control deflection corresponds to 0-100% throttle), reversing (allows to switch on the reversing of the motor running by another channel with a switch).
Brake Force: The braking intensity is adjustable from Level 1 to Level 7 for "Normal Brake" mode.
Cutoff type: Soft Cutoff: the contESCroller will gradually reduce power to 50% of full power within 3 seconds after voltage protection is activated. Hard Cutoff.
Number of LiPo cells: We recommend setting manually for 100% reliable voltage protection function. The ESC will automatically calculate the number of cells of the connected battery according to the "3.7 V per cell" rule if you select automatic detection.
Cutoff Voltage: The threshold level of the voltage protection is adjustable from 2.8 to 3.8 V/cell; the protection can also be switched off completely.
Start-up Mode: Normal start-up (instant start-up), Soft start-up (with slow start for motors with large propellers, gearbox or smaller EDF), Very soft start-up (with very slow start for motors with large propellers, gearbox or EDF from 90 mm).
Timming: Adjustable from 0-30°.
Motor direction: CW/CCW
DEO Freewheeling: This feature can be turned on or off; it can provide better linearity or smoother throttle response.

PROTECTIVE FUNCTIONS OF THE ESC
Start-up protection The ESC measures the motor speed during start-up. If the speed stops increasing or the increase is not stable, the ESC evaluates this as an incorrect start-up. If the throttle is at less than 15% at this point, the ESC will automatically attempt to restart the motor; if the throttle is at more than 15%, you must pull the throttle control all the way down to restart the motor.
Thermal protection of the ESC: The motor will "stall" if the ESC temperature exceeds 110°C, indicating that thermal protection has been activated. If the throttle control is pulled back below 60% at that point, the "stutter" will disappear and the ESC will deliver power appropriate to the throttle position. If you move the throttle above 60%, the "stutter" will reappear. The temperature of the ESC must not exceed 70°C when switching on, otherwise the engine cannot be started.
Signal loss protection The ESC will immediately shut down the motor if the signal is absent for 0.25 s to prevent even more damage and risks from a rapidly rotating rotor or propeller. Once a normal signal is received, the ESC resumes normal operation.
Overload protection The ESC switches off the motor or restarts automatically when its load suddenly increases to a very high value.
Overcurrent protection: The ESC immediately switches off the motor if the peak current draw exceeds the maximum permitted value; it then resumes normal operation. If the current draw still exceeds the maximum permitted value, the motor is switched off completely.
NOTE:The throttle cable of the ESC is the two-wire lead (white + black wire), the programming cable is the 3-wire lead (white + red + black wire). Connect ONLY the throttle cable to your receiver.
Tip: When the first time the regulator is switched on, first calibrate the throttle range according to the instructions. Only then can the ESC be used and other parameters set using the transmitter or the KAVAN PRO LED programming card.
Use: Airplane,helicopter
Type: brushless ; Current rate [A]: 160 ; Max. peak current [A]: 200 ; LiXX cells: 6 - 14 ; Lenght [mm]: 110 ; Width [mm]: 50 ; Height [mm]: 33 ; Weight [g]: 221 ; Regulation type: one-way ; Brzda: Yes ; Sensor input: No ; Programmable: Yes Used for Aeroplane,Helicopter Type AC Constant current [A] 160
Max. peak current [A] 200
LiXX cells 6 - 14
Length [mm] 110
Width [mm] 50
Height [mm] 33
Weight [g] 221
Control one-way
Brake Yes
Sensor imputs No
Programmable Yes


Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x Electric spoiler 440 mm (2 pcs)
1 x Canopy Sweet / Siesta
1 x Electric spoiler 300 mm (2 pcs)
1 x 250 mm / 16 mm Airbrakes
1 x Electric spoiler 250 mm (2 pcs)
1 x Windsock Ozone L -1200 mm
1 x Aramid 50 daN 50 m
2 x Para-RC Mix
1 x Paramotor BackPack XXS (without accessories)
1 x Rescue 1,8m2 / BackPack
1 x Parachute P4
1 x Paramotor BackPack XXS 2
1 x Wing OXY 5,0 m2
1 x MAX pilot ARTF
2 x Para-RC "RC-Evo-Cross" Rescue
1 x Para-RC Trike "RC-Bullix"
1 x Chili Race F3K (aramid nose)
1 x Chili Race F3K 2 wing servo mounted(carbon biax)
1 x X-RAY Micro QR (Rudder)
1 x Softshell Hispano Aviación
1 x Brass hexagonal rod Ø 3 mm x 1000 mm
1 x Towing hook
1 x Optical RPM Sensor
1 x Straightened rod Ø 14.0 mm x 1000 mm
1 x Brass rod Ø 1.0 mm x 1000 mm
1 x SE Ring 250 mm (2 pcs)
1 x Spray YELLOW Inca Lexan 150ml
1 x Tape GFK 25 mm
1 x Conector FUTABA Servo male BLUE silicon (10 pcs)
1 x 18 mm reinforced hinge
1 x Banna gold connector 2,5 mm (M/F)
1 x 5 mm M2 variable horn
1 x Conector XT-30 (macho)
1 x 2 mm male connector (2 pcs) with safety connector
1 x Zurich Sport Sunglasse Dark Sensity MAGENTA Glasses
2 x Pin hinge 39x20 mm (10 uds)
2 x M3/5 Diam metal short ball link V3 (2 pcs)
2 x 58 mm PVC transparent battery termo-retract 68 mm (1 m)
1 x Medium pin type hinge (12 uds)
1 x Horn 13,5x16 mm (2 pcs)
1 x 15 mm reinforced hinge
2 x Socket head ball link M3 (2 uds)
2 x Conector JR Servo female (10 pcs)
2 x Monokote BLUE metalizado (1.8x0.65m)
1 x ABS tube 16.0x14.0x1000 mm
1 x 20 mm carbon horn
1 x Brass control horn M4 short for wire (10pcs)
1 x ABS tube 3.0x2.0x330 mm
1 x ABS tube 5.0x3.0x1000 mm
2 x Oracover Black 10 m
1 x Aluminium tube (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x Conector JR/Uni Servo female BLUE silicon (10 pcs)
1 x Conector FUTABA Servo female BLUE silicon (10 pcs)
1 x ABS tube 2.0x1.0x1000 mm
2 x Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
2 x Support ECU Xicoy X-45
2 x Glases Moritz
1 x ABS tube 12.0x10.0x1000 mm
1 x Civilian pilot "Gramps" size 9cm (Slimline)
2 x Dean "T" - Futaba Adapter
1 x 1/4 Pilot "Heidi"
1 x Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x Extension S-Bus 1-2 silicon 120 cm FUTABA
2 x Aluminium coupler M3/2 with ball bearing (1 pcs)
1 x Extension silicon 10 cm (Futaba)
1 x Extension 90 cm (Futaba)
1 x Suncover 100cc Red
1 x Squared carbon wing joinner 5x5x220 mm
2 x Sun Cover PC 21 XXL (JMB Jets)
1 x Militarian pilot "Kamikaze" size 9cm (Slimline)
1 x Extension silicon 100 cm (Graupner)
1 x Carbon fiber rod 7.0 mmx1000 mm
1 x Carbon fiber rod 12 mm x 1000 mm
1 x 2 LiPo XH>EH adapter
1 x Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x Piloto RC Civil 1/5- 1/6 Scale 12"
1 x F450/550 Quadcopter, landing gear
1 x Ciano KAVAN Thick 20g
1 x Ball Link M2 with Ball and Hardware, 10 pcs
1 x Waterproof adhesive tape, width 19mm, length 25m
1 x Chili F3K 2 wing servo mounted
1 x 
1 x X-RAY Micro QR
1 x 110x55 mm SLH KOVO wheel
1 x 1/12 Pilot "Cougar"
1 x Joint with bearing M3 22x5,5
1 x Socket head ball link M3 (2 uds)
1 x Long ball link M2 (6 uds)
1 x Blue metalic ball link M2/2 azul (2 pcs)
1 x Nylon hinge 20x15x0,3 (10 pcs)
1 x Steel tube (L 1000 mm Ø12 mm, Ø11,7 mm)
1 x Fiberglass tube 6/4x1000mm
1 x Pin type hinge Al 3,0x50 mm (2 pcs)
1 x Steel tube (L 1000 mm Ø8 mm, Ø7,7 mm)
1 x 2 piece mounting frame Battery 3200 / 4000
1 x 1,2x1000 mm 2:1 red termoretract tube
1 x 2,4x1000 mm 2:1 red termoretract tube
1 x Micro flex hinge (12 uds)
1 x Conector JR Servo male (50 pcs)
1 x 4,8x1000 mm 2:1 black termoretract tube
1 x Threaded coupler M2 (10 uds)
1 x Extension 6 lipos XH > EH
1 x Ball link Aluminio M3 (2 pcs)
1 x SPS 70V 140/280 A
1 x Ball link Aluminio M3 x 3 x 5 x 18mm (6 uds)
1 x Z type of cable coupler Ø 1 (2 uds)
1 x Extension 5 lipos JST/C - JST
1 x Kwik link AL M3 con Clip (2 pcs)
1 x Kwik link aluminio IZD. M3 L: 30mm (6 uds) pin Ø 2 mm
1 x Carbon fiber rod 16 mm x 1000 mm
1 x 105 mm PVC transparent battery termo-retract 68 mm (1 m)
2 x 135 mm PVC transparent battery termo-retract 68 mm (1 m)
1 x PVC transparent battery termo-retract 51 mm (1 m)
1 x 3,2x1000 mm 2:1 red termoretract tube
2 x 6,4x1000 mm 2:1 green termoretract tube
1 x Ball link M2,5 (10 pcs)
1 x Support Antena 2.4 Ghz (2 pcs)
1 x Ball link M3 (10 pcs)
1 x M2 5Diam short black ball link V2 (2 pcs)
1 x Tapa estado carga XT-60 (6 pcs)
1 x 6 mm hexagonal ball link M3 (10 pcs)
1 x M2,5 Diam metal ball link V3 (2 pcs)
1 x Aro pasacable Ø20 mm (4 pcs)
1 x Ball link M2 (10 pcs)
1 x Support pump Xicoy X45
1 x Ball link M3 (10 pcs, flat ball)
1 x Zurich Sport Sunglasse Dark Sensity BROWN Glasses
1 x Aro pasacable Ø25 mm (4 pcs)
1 x Glases Innovation Plus
1 x Support Pitot JETI
1 x Support conector MPX (6 pcs)
1 x M3 INDUSTRIAL ball link (2 uds)
1 x M2,5 5Diam short black ball link V2 (2 pcs)
1 x M3 Maxi ball link (2 uds)
1 x Support XT60 conector (2 pcs)
1 x Recessed MPX connector support (6 pcs)
1 x Soporte filtro FESTO (4 pcs)
1 x Ball link M1.6 (6 uds)
1 x M2,5 5Diam metal ball link V3 (2 pcs)
1 x Joint with bearing M2 22x5,5
1 x Glases Stratus
1 x Tube support Ø 6mm (10 pcs)
1 x Angle support XT60 conector
1 x Support Flush MPX Conector (6 pcs)
1 x Glases Flitemaster
1 x Support FUEL DOT V3
1 x 6 mm ball link M3 (10 pcs)
1 x Ball link M3 (6 uds)
1 x Short ball link M2 (6 uds)
1 x M2,5 Diam metal short ball link V3 (2 pcs)
1 x Sun Cover BULL Mo1 2.6 (Hispano Aviacion)
1 x Long ball link M3 (6 uds)
1 x Pasacables rectangular 40x15 mm (4 pcs)
1 x M2/M1/6 3Diam short black ball link V1 (2 pcs)
1 x M2,5 5Diam black ball link V2 (2 pcs)
1 x Nylon hinge for flaps 33x9 (2 pcs)
1 x Steel tube (L 1000 mm Ø7 mm, Ø6,7 mm)
1 x BlueCom™ Adapter (iOS)
1 x Robart Door Hinge (Pk2)
1 x Indoor hinge with servo arm integraded
1 x Hard brass tubing (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x Cable servo PREMIUM MAXI 1 m (blanco/rojo/azul) PVC
1 x 19 mm 2:1 black termoretract tube
1 x LightBox SR
1 x Gates hinge 30x16 mm (2 pcs)
1 x Small pinned hinge (12 uds)
1 x Nylon hinge 15x0,3 (10 pcs)
1 x Charger 220/110v
1 x 3,2x1000 mm 2:1 black termoretract tube
1 x Oracover CHROME 2m
1 x 12.7 mm 2:1 black termoretract tube
1 x 37 mm PVC transparent battery termo-retract (1 m)
2 x 10m servo "Premium" wire (white/red/blue)
1 x 6,4x1000 mm 2:1 blue termoretract tube
1 x Cable set Premium™ MAXI "one4two"
1 x 165 mm PVC transparent battery termo-retract 165 mm (10 m)
1 x Nylon hinge for flaps/gates 27x10,5 (2 pcs)
1 x Steel tube (L 1000 mm Ø6 mm, Ø5,7 mm)
1 x 30 cm DEANS female connector
1 x Oracover Brown 2 m
1 x Pin type hinge Al 3,0x50 mm demount (2 pcs)
1 x Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
1 x Gates hinge
1 x 12V Car Adapter
1 x Miniature brass strap hinge, 1 m
1 x 1,2x1000 mm 2:1 black termoretract tube
1 x Small flex hinge (12 uds)
1 x Charging Extension 50cm for 2 Battery
1 x ORACOVER Fluor red (2 m)
1 x Cable servo PREMIUM MAXI 50m (blanco/rojo/azul) PVC
1 x Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x 1 m servo "Premium" wire (white/red/blue)
1 x Oracover Black 2 m
1 x Long pinned hinge (12 uds)
1 x Oracover Azul 2 m
1 x 12,7x1000 mm 2:1 green termoretract tube
1 x Monokote PLATINO metalizado (1.8x0.65m)
1 x 4,8x1000 mm 2:1 blue termoretract tube
1 x Hard brass tubing (L 1000 mm, Ø6.0 mm, Ø5.2 mm)
1 x Nylon hinge 20x20x0,3 (10 pcs)
1 x Gates hinge black 30x16 mm (2 pcs)
1 x Crimping tool
1 x Conector JR Servo female (50 pcs)
1 x Pin type hinge Al 4,5x70 mm (2 pcs)
1 x Extension MPX-MPX 20 cm
1 x 2,4x1000 mm 2:1 black termoretract tube
1 x Long pinned hinge (6 uds)
1 x Hard brass tubing (L 1000 mm, Ø4.0 mm, Ø3.1 mm)
1 x MYLAR film A350 (1000x500 mm)
2 x 200m servo "Premium" wire (white/red/blue)
1 x Extension for LC-Display 50cm
1 x Fast'n EZ-CA-Hinge (12 uds)
1 x Steel tube (L 1000 mm Ø3 mm, Ø2,7 mm)
1 x 100m servo "Premium" wire (white/red/blue)
1 x Cable servo PREMIUM MAXI 10m (blanco/rojo/azul) PVC
1 x BlueCom™ Adapter (Android / WP)
1 x Thinwall Stainless Steel Tubing 28x0.6x1000 mm
1 x 2,4x1000 mm 2:1 green termoretract tube
1 x Hard brass tubing (L 1000 mm, Ø5.0 mm, Ø4.1 mm)
1 x Oracover CARBON Metalic 1 m
1 x Xplorer2 anemometro
1 x ALBATROS L-39 G2 "Camo Tiger" Turbine ready
1 x Switching module high voltage SXH
1 x Clevis plastico I=45 mm / hole 3mm / pin 1 (2 pcs)
1 x JETImodel DPS 40
1 x Threaded coupler ALU M2,5 Ø 4 (2 uds)
1 x PSC 6
1 x Couple M4 for wire (10 pcs)
1 x USB interface ALTIS
1 x SPS Remote switch actuator
1 x PowerBox SparkSwitch RS
1 x Crimping sleeves for 1.1 mm cable (10 pcs)
1 x Prolonguer for Balancer Thunder Power 6S
1 x UBEC 6A KAVAN
1 x Brass ball links BS M3 V1 (10 pcs)
1 x Threaded coupler M2,5 Ø 3 mm (10 pcs)
1 x Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x Threaded coupler ALU M3 Ø 5 (2 uds)
1 x Aluminium blue ball links M3 V1 (10 pcs)
1 x Extension 5 lipos JST/C
1 x Kwik link AL M3 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x Pins M connect Multipin connectors AWG 20-24
1 x MAX BEC 2
1 x SBEC 40
1 x Extension 2/3 lipos JST - JST/C
1 x MAX BEC 2D plus EX
1 x Carbon fiber rod 2.0 mmx1000 mm
1 x Kwik link AL M3 L:30 mm (2 pcs) + Pin Ø 2,0 mm
1 x Carbon fiber rod 5.0 mmx1000 mm
1 x Pulley brass 14/2 (2 pcs)
1 x Small kwik link (10 pcs)
1 x Pulley brass 10/2 (2 pcs)
1 x Carbon wing joinner 13,4 mm Ø 0,48 mm
1 x Pegamento Pu R 50g polyuretano
1 x UHU Por 50ml/40g
1 x Allen wheel collar M4x4
1 x Black silicone 1,0 qmm wire (50 m)
1 x Cable grommet Ø 5 mm (4 uds)
1 x Strip ABS 2.0x5.0x1000 mm
1 x Initior Receiver FRX2 Wireless
1 x Electric rocket starters (6 pcs)
1 x Superlight deluxe wheel 40 mm (2 pcs)
1 x Superlight deluxe wheel 56 mm (2 pcs)
1 x Ply-Span 450x600/13g Black
1 x Cable tie mounts 4.3 (4 uds)
1 x Protective Cover for wires Ø 3 mm 1000 mm
1 x 90 mm rods + T patellas set for direction control
1 x 5 line servos wire black (1 m)
1 x Green smoke canister 65 g
1 x Round Rod 6,0x1000 mm
1 x Red smoke canister 100 g
1 x Smoke set "S"
1 x Initior Transmitter FTX2 Wireless
1 x Servo GO-1023MG 7.0 kg.cm 0.09s/60º
1 x Superlight deluxe wheel 45 mm (2 pcs)
1 x A/C quality beech plywood 600x300x0.8 mm
1 x M3 Maxi ball link (2 uds)
1 x Birch plywood plate 600x300x1.5 mm
1 x Superlight wheel 100 mm with valve (2 pcs)
1 x Round Rod 1.0x3.5 cm
1 x Birch plywood plate 600x300x1.2 mm
1 x ESC KAVAN R-80SB SBEC 80A
1 x Swashplate metal LAMA
1 x 
1 x Microbalon filler for CA glues. Packaging bottle 20g
1 x M3 Maxi ball link (2 uds)
1 x Servo GO-09 9g
10,403.62EUR
Manufacturers
Manufacturer Info
Kavan
Other products
Languages
Español English
Currencies