184.00EUR

ESC KAVAN PRO-160HV Opto 160 Amp
[KAV3231055]

Programmable brushless ESC for big high-voltage (HV) aircraft models. Continuous current 160A (peak 200A), 6–14 LiPo cells power, OPTO (galvanically isolated control and power electronics). Weight: 221g; dimensions: 110x50x33mm. Programmable microprocessor ESC for brushless, sensorless AC motors ("brushless, sensorless") for hobby and sport aircraft models with LiPo/Li-ion/LiFe battery power supply. It uses advanced optimized control technology to significantly improve throttle response and power stage control efficiency. The ESC design takes into account the high long-term load capacity and durability required in giant models when powered by a high cell count battery. The power section of the ESC is galvanically isolated from the control electronics to provide high immunity to interference at high operating currents and high supply voltages. The ESC is not equipped with a BEC for the receiver and servos. A special KAVAN PRO LED programming card, which is supplied separately, is used to easily set up the ESC.
DESCRIPTION AND FUNCTIONS OF THE ESC
The ESC features a high-performance 32-bit ARM M4 microprocessor with a clock frequency of up to 72 MHz; it is compatible with most brushless motors.
Suitable for the vast majority of aircraft brushless motors powered by 6-14S LiPo/Li-ion/LiFe batteries.
Special power stabilizer for microprocessor for high interference immunity and reduced risk of loss of control.
Optimized control technology significantly improves throttle response and power stage control efficiency and reeduces ESC temperature.
Galvanically isolated power part by optoelectronic component.
Normal/Soft/Very Soft start-up modes are suitable for normal propeller aircraft and models with EDF.
Easy programming and setup using the transmitter or the KAVAN PRO LED programming card.
A special programming cable for connecting the ESC to the LED programming card allows the user to program the ESC anytime and anywhere (see the KAVAN PRO LED programming card manual for details).
Normal/Proportional/Reversal brake modes (especially reversal mode) can effectively shorten the range after landing.
A number of protection functions: start-up protection, thermal protection of the ESC, thermal protection of the capacitors, overload protection, overcurrent protection, abnormal supply voltage protection and control signal loss protection effectively extend the life of the ESC.
Calibrate the throttle range to perfectly match the control signal from your RC kit.

PROGRAMMABLE FUNCTIONS
Brake Type Brake off, normal brake (with braking intensity adjustable in 7 levels), proportional brake (controlled by the throttle control: 0-20% of throttle control deflection corresponds to 100-0% brake, 20-100% of control deflection corresponds to 0-100% throttle), reversing (allows to switch on the reversing of the motor running by another channel with a switch).
Brake Force: The braking intensity is adjustable from Level 1 to Level 7 for "Normal Brake" mode.
Cutoff type: Soft Cutoff: the contESCroller will gradually reduce power to 50% of full power within 3 seconds after voltage protection is activated. Hard Cutoff.
Number of LiPo cells: We recommend setting manually for 100% reliable voltage protection function. The ESC will automatically calculate the number of cells of the connected battery according to the "3.7 V per cell" rule if you select automatic detection.
Cutoff Voltage: The threshold level of the voltage protection is adjustable from 2.8 to 3.8 V/cell; the protection can also be switched off completely.
Start-up Mode: Normal start-up (instant start-up), Soft start-up (with slow start for motors with large propellers, gearbox or smaller EDF), Very soft start-up (with very slow start for motors with large propellers, gearbox or EDF from 90 mm).
Timming: Adjustable from 0-30°.
Motor direction: CW/CCW
DEO Freewheeling: This feature can be turned on or off; it can provide better linearity or smoother throttle response.

PROTECTIVE FUNCTIONS OF THE ESC
Start-up protection The ESC measures the motor speed during start-up. If the speed stops increasing or the increase is not stable, the ESC evaluates this as an incorrect start-up. If the throttle is at less than 15% at this point, the ESC will automatically attempt to restart the motor; if the throttle is at more than 15%, you must pull the throttle control all the way down to restart the motor.
Thermal protection of the ESC: The motor will "stall" if the ESC temperature exceeds 110°C, indicating that thermal protection has been activated. If the throttle control is pulled back below 60% at that point, the "stutter" will disappear and the ESC will deliver power appropriate to the throttle position. If you move the throttle above 60%, the "stutter" will reappear. The temperature of the ESC must not exceed 70°C when switching on, otherwise the engine cannot be started.
Signal loss protection The ESC will immediately shut down the motor if the signal is absent for 0.25 s to prevent even more damage and risks from a rapidly rotating rotor or propeller. Once a normal signal is received, the ESC resumes normal operation.
Overload protection The ESC switches off the motor or restarts automatically when its load suddenly increases to a very high value.
Overcurrent protection: The ESC immediately switches off the motor if the peak current draw exceeds the maximum permitted value; it then resumes normal operation. If the current draw still exceeds the maximum permitted value, the motor is switched off completely.
NOTE:The throttle cable of the ESC is the two-wire lead (white + black wire), the programming cable is the 3-wire lead (white + red + black wire). Connect ONLY the throttle cable to your receiver.
Tip: When the first time the regulator is switched on, first calibrate the throttle range according to the instructions. Only then can the ESC be used and other parameters set using the transmitter or the KAVAN PRO LED programming card.
Use: Airplane,helicopter
Type: brushless ; Current rate [A]: 160 ; Max. peak current [A]: 200 ; LiXX cells: 6 - 14 ; Lenght [mm]: 110 ; Width [mm]: 50 ; Height [mm]: 33 ; Weight [g]: 221 ; Regulation type: one-way ; Brzda: Yes ; Sensor input: No ; Programmable: Yes Used for Aeroplane,Helicopter Type AC Constant current [A] 160
Max. peak current [A] 200
LiXX cells 6 - 14
Length [mm] 110
Width [mm] 50
Height [mm] 33
Weight [g] 221
Control one-way
Brake Yes
Sensor imputs No
Programmable Yes

under request

Reviews

Quick Find

Shopping Cart

2 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
2 x	Carbon fibre sandwich sheet 350x150x3 mm
2 x	Aluminium sheet 500x250x0,5mm
2 x	Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 3m
2 x	Buy Perforated film 145 cm / 50 m
1 x	Breatex™ Non-woven absorber 150 g/m² Roll 100m
1 x	Breatex™ Non-woven absorber 150 g/m² Roll 50m
3 x	800TVL CMOS camera for FPV
2 x	ABS 500 x 400 x 2,0 mm (white)
1 x	Buy Perforated film 100 cm / 50 m
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 10 m
3 x	Breatex™ Non-woven absorber 300 g/m² Roll 41 m
2 x	ARAMID honeycomb 1300x2600x2 mm
3 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x	Buy Perforated film 100 cm / 10 m
2 x	ABS 500 x 400 x 1 mm (white)
1 x	Carbon fibre sleeve 12k 170 mm x 5m
3 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
2 x	USB Mini Camera endoscope
2 x	Carbon fabric 160 g/m² (plain weave) 100 cm x 2 m
2 x	ABS 500 x 400 x 1,5 mm (white)
1 x	SE Ring HACKER 300 mm (2 pcs)
1 x
2 x	Tape GFK 50 mm
1 x	Ring 320 mm length (5 pcs)
1 x	14x60 mm Mini rings Tie Wraps (4 pcs)
1 x	Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x	SE Ring 480 mm (2 pcs)
1 x	26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x	Cinta Goldfix 1m
1 x	SE Ring 350 mm (2 pcs)
1 x	Spikes Band (5 m)
1 x	SE Ring 450 mm (2 pcs)
1 x	Foil for sticking flaps and ailerons
1 x	5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
2 x	SE Ring 360 mm (2 pcs)
1 x	SE Ring 400 mm (2 pcs)
2 x	SE Ring 240 mm (2 pcs)
1 x	20x1000 mm Ring Strap Back To Back
2 x	Tape GFK 38 mm
1 x	RUDDOG Protection and Heat Shield Tape (2mx50mm)
1 x	20x200 mm battery rings
1 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	Carbon fabric 68 g/m² (style 493 aero, plain weave) 100 cm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
1 x	Carbon fibre tape 200 g/m² (unidirectional) 50 mm
2 x	Breatex™ Non-woven absorber 150 g/m² Roll 5 m
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 20 m
1 x	Carbon fabric 160 g/m² (twill weave) 127 cm, roll/ 10 m
1 x	Breatex™ Non-woven absorber 150 g/m² Roll 20m
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
2 x	Carbon Non-crimp ST 100 g/m² 50 cm x 10 m
2 x	Stickers-digit for marking
1 x	Small Crow DLE-170M
1 x	Silent-blocks DLE 170M
1 x	Motor DLE 430 cc - Paramotors
1 x	Motor DLE 170 M- Paramotors
1 x	Big Crow DLE-170M
1 x	Motor DLE 200cc Std
1 x	Motor DLE 200cc Premium Muffler
1 x	Double conector with JR adapter and 200 mm extension
1 x	Red smoke bombs AX-60 (5 pcs)
1 x	"S" set for boats
1 x	Smoke set "M"
1 x	Protective Cover for wires Ø 3 mm 1000 mm
1 x	Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x	Silicone adhesive ELASTOSIL® E4, tube/ 90 ml
1 x
1 x	Demoulding wedge red (40 x 20 mm) 5 pcs
1 x	Extension silicon 25 cm (Graupner)
1 x	Cabin latch Fox MDM1 4m (pair)
1 x	Glases Innovation Plus
1 x	Glases Moritz
1 x	2,3 mm Prop Adapter M5
1 x	2 mm Prop Adapter M5
1 x	5 mm Prop Adapter M6
1 x	6 mm Prop Adapter M8
1 x	Carbon plate 550x350x3.0 mm ECOTECH
1 x	Carbon plate 350x150x1.5 mm
2 x	Fiberglass plate 350x150x1.5 mm
1 x	Chopped glass fibre strands 3 mm
1 x	Carbon Non-crimp ST 200 g/m² 50 cm x 10 m
1 x	Thermoforming sheet 0.3mm (0.039in) DIN A4
1 x	Carbon plate 550x350x1.0 mm ECOTECH
4 x	Styrene plate 320x120x0.5 mm
1 x	Carbon roving DowAksa / 24k / 1600 tex
3 x	Sandwich carbon + poplar 2mm + carbon 480x290 mm
2 x	PVC plate 320 x 194 x 0.23 mm (brown)
1 x	Chopped glass fibre strands 3 mm
1 x	Suncover 100cc Red
1 x	Carbon plate 350x150x4.0 mm
1 x	Carbon plate 550x350x2.5 mm ECOTECH
1 x	Carbon Non-Woven, 160 g/m² 100 cm 10 m
1 x	Carbon plate 350x150x3.0 mm
1 x	Fiberglass plate 1200x1000x0,2 mm
1 x	Glass fibre sleeve Ø 20 mm X 20m
3 x	Fiberglass plate 620x540x2,0 mm
2 x	Foam plastic plates (310x210x5 mm)
1 x	Fiberglass plate 350x150x2.0 mm
1 x	Fibra vidrio 25g 110 cm/ 10m (Interglass 02034, finish FE800 pl
1 x	Sandwich carbon + poplar 3mm + carbon 290x160 mm
1 x	Fibra de vidrio 100 g/m² (50 m x 100 cm)
1 x	Suction funnel for carburetor WALBRO 20-80cc (red)
1 x	Ventus 1:4 set of instruments
1 x	Reed valve for DA 50-R
1 x	SE Ring 200 mm (2 pcs)
1 x	Tape GFK 25 mm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	CC 02
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	Prolonguer for Balancer Thunder Power 6S
1 x	Male/Female prolonguer for Balancer Thunder Power 6S
1 x	4 LiPo XH>EH adapter
2 x	CellPRO 4S Adaptader (GP/KO up to 4S)
1 x	Female connector for 6 pines AWG
1 x	PSC 5
1 x	Extension 2/3 lipos JST/C
1 x	TP/TopFuel - JST-EH 4/5S Adapter
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	Fiberglass plate 620x540x3,2 mm
2 x	Sandwich carbon + poplar 3mm + carbon 480x290 mm
1 x	Thermoforming sheet 0.1mm (0.004in) DIN A5 (5 pcs)
1 x	Sandwich Carbon fibre Rohacell (800 x 280 x 3 mm)
1 x	Fiberglass plate 350x150x2.5 mm
2 x	Fiberglass plate 350x150x4.0 mm
2 x	Release film 100 cm x 50 m
1 x	Teflon rollers 80 mm x 15 mm Diam.
1 x	Fiberglass plate 350x150x3.0 mm
1 x	FUNRAY RR
1 x	IKURA 4.0 m
1 x	Albatros red/white (Top Model)
1 x	IKURA GPS 4.28 m
1 x	ASG 32 560 mm
1 x	Extension 5 lipos JST - JST/C
1 x	30 cm BEC cable (female)
1 x	Crystal RX 35.120 Ch 72
1 x	Transmitter Crystal 35 Mc/s Ch 77
1 x	3.2 mm Prop Adapter M6
1 x	Film release agent PVA 25 ml
1 x	Foam plastic plates (310x210x2 mm)
1 x	Balsa panel 8.0x100x1000 mm
1 x	Combustible Glow "KAVAN" air/heli 10% nitro
1 x	Glass fabric 25 g (2 m²)
1 x	KAVAN CA Activator 150ml
1 x	Glass fabric 25 g/m² (1 m²)
2 x	Sheet Depron Aero 1250x800x3 mm
1 x	2 mm Prop Adapter M6
1 x	Fast'n EZ-CA-Hinge (12 uds)
1 x	Fuel bottle 500 ccm
2 x	BULL MØ1 2.600mm "ALPINE"
1 x	Carbon Non-Woven, 240 g/m² 100 cm x 2m
1 x	Carbon plate 550x350x1.5 mm ECOTECH
1 x	Glass fabric 80 g/m² (plain) 100 cm, roll/ 20 m
1 x	Frontal Adapter for AXI53xx
1 x	10 mm aluminium spinner (Kavan)
1 x	Thermoforming sheet 0.5mm (0.02in) DIN A4
1 x	Fiberglass plate 620x540x1,0 mm
1 x	Vacuum sealing tape, 2.5 x 12 mm (up to 140 °C) 22 roll
1 x	Tank GFK Opus/JEt 300 ml
1 x	Fiberglass plate 620x540x0,3 mm
1 x	ULTIMATUM 2.0 m orange/blue
1 x	ULTIMATUM 2.0 PRO "McLAren"
1 x	ULTIMATUM 2.0 PRO "Full Carbon Red"
1 x	PET film Mylar® A 350, 50 cm, roll/ 2 m
1 x	Glass fabric 49 g/m² (1,27 x 10 m)
1 x	Peel ply 95 g/m² (plain weave) 100 mm x 100 m
1 x	Sun Cover PC 21 XXL (JMB Jets)
1 x	Carbon plate 350x150x5.0 mm
1 x	BULL MØ1 2.600mm "RED BULL"
1 x	Fiberglass 25 g/m² 5000x1270 mm
1 x	Y-Hose connector 3-3-3 mm
1 x	Racor 2/3 mm
1 x	Propeller 9x7 SlowFlyer
1 x	Walbro carburetor for MVVS 26/30/35/40 cc
1 x	Waterproof adhesive tape, width 19mm, length 25m
1 x	Extension Arm for Carburetor (red)
1 x	FIALA Propeller 19x12 Electric
1 x	Black copper lacquer wire Ø0,2 mm (5 m)
1 x	MAX BEC 2
1 x	3-blades 27x12 carbon prop Super Silence
1 x	Switching module high voltage SXH
1 x	DPSI Micro-DualBat 5.9V / 7.2V MPX-JR
1 x	Crystal Universal RX 35.020 Ch 62
1 x	Crystal Universal RX 35.130 Ch 73
1 x	40 mm servo arm with bearing (2 pcs)
1 x	Micro Crystal RX 35.120 Ch 72
1 x	Canopy F9F Panther (Aero-naut)
1 x	Cancamo con aro 16/6.5 mm (10 pcs)
1 x	PH5 adapter for 5mm M8 axi for AXI2820 y 2826
1 x	T-Hose connector 3-3-3 mm
1 x	Propeller hub spacer 8/5.5
1 x	T-Hose connector 3-3-3 mm
1 x	Quick hose connector 6-6 mm
1 x	Tap FESTO 4-4 mm
1 x	Racor 4/3 mm
1 x	Propeller 3x2
1 x	Propeller FIALA 15x8 3-Blade
1 x	Propeller MENZ-S 20x12
1 x	3 copper lacquer wire Ø0,2 mm (1 m)
1 x	PWC6 PowerWingConnector for 6 servos with fuselage socket
1 x	PowerBox SparkSwitch RS
1 x	28x12 prop Super Silence
1 x	Interruptor SAFET-SWITCH 12HV Twinbatt
1 x	DPS Switch JR/JR
1 x	3-blades 20x12 carbon prop Super Silence
1 x	wing/fuselage connector for 16 pines AWG 20-24
1 x	8 mm Adapter for AXI53xx
1 x	Propeller 12x6 Falcon electric
1 x	Crystal Universal RX 35.030 Ch 63
1 x	Crystal Universal RX 35.020 Ch 62
1 x	Crystal Universal RX 35.140 Ch 74
1 x	USB Charger 12V DC for car
1 x	CAM-Carbon Light Prop 13x6" (Prop left)
1 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	Cianocrilato MD GEL 454 tube 20g
1 x	Birch plywood plate 600x300x2.5 mm
1 x	M3 Maxi ball link (2 uds)
1 x	Extension 15 cm (Futaba)
1 x	Carburator joints for SAITO FA80/80GK/72/72GK
1 x	Carbon tube (L 1000 mm, Ø14 mm, Ø12 mm)
1 x	Cap closure 33/23.5mm (2 uds)
1 x	Carbon fiber rod 1.5 mm x 1000 mm
1 x	CAM-Carbon Light Prop 14x6" (Prop left)
1 x	Carbon tube (L 1000 mm, Ø18 mm, Ø16 mm)
1 x	Carbon fiber flat 1000x3.0x1.0 mm
1 x	CAM-Carbon Light Prop 12x6"
1 x	CAM-Carbon Light Prop 12x5" (Prop right)
1 x	Servo M2x9/16 screw (4 pcs)
1 x	SAVAGE Max Red 1080 mm
1 x	DUPLEX backpack for Jeti DS handheld transmitter
1 x	Glass fabric 163 g/m² 130cmx5m (Interglas 92105, aero, finish
1 x	Superlight wheel 125 mm with valve (2 pcs)
1 x	ESC KAVAN PRO-160HV Opto 160 Amp
1 x	A/C quality beech plywood 600x300x6.0 mm

55,836.70EUR