120.00EUR

Combo KAVAN PRO 3542-1150 + KAVAN PRO-80 SB
[KAV30.1638C]

Combo set of BLS motor with 80A ESC for model aircraft: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 rpm per V, power supply Lixx 3-4s, shaft 5 mm.

Outrunner brushless electric motor for model aeroplanes: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 RPM/V, input voltage 3-4S Lixx. 5.0mm shaft. Alternative designation based on the stator dimension: 2820-1150. KAVAN PRO series motors are high performance 14-pole brushless outrunners. State-of-the-art design, hardened steel shafts, high quality ball bearings, High grade material used for stators and rotors ensure long lifetime and unbeatable performance and high efficiency. KAVAN PRO series motors are low revolution/high torque electric motors capable of swinging large diameter propellers without need for a gearbox.
KAVAN PRO 3542-1150 is a motor for model aeroplanes up to 2200 g all-up weight powered by 3-4S LiPo flight battery pack. It is great for faster 2000-2500 mm electric powered gliders, 1400-1500 mm high wing trainers, scale and aerobatic models.
Motor installation: KAVAN 3542-1150 has been designed both for the front and radial mount installation. Front mount: Use four M3 screws; these may not go deeper than 3-4 mm into the front case. Radial mount: Use four M3 screws to secure the mounting cross to the firewall. The firewall should be made of 4.0-5.0 mm plywood. The radial mount set is supplied with the motor.
The motor set contents: KAVAN PRO 3542-1150 motor w. cables (3.5 mm gold-plated connectors), radial mount set accessories. The full instruction manual can be downloaded here: KAVAN PRO Brushless Motors Instruction Manual
Note: Alternative designation based on the stator dimensions: 2820-1150.
Powering LiXX cells 3 - 4
RPM/V [ot./min/V] 1150
Max. power (180 s) [W] 1000
Internal resistance [mOhm] 16
Open-circuit current (při 10 V) [A] 2.7
Max. peak current (180 s) [A] 70
Diameter [mm] 35.2
Length [mm] 41
Length celková [mm] 63.5
Shaft diameter [mm] 5
Weight [g] 141
Poles count 14
Timing [°] 20 - 25
ESC [A] 70 - 80
Weight of glider (up-to) [g] 2200
Weight of trainer (up-to) [g] 2100
Weight of acrobat (up-to) [g] 1800
Weight of 3D (up-to) [g] 1200
Doporučená vrtule 3S: 11x8"-12x6"
4S: 9x6"-10x5.5”

under request

Reviews

Quick Find

Shopping Cart

2 x	Blue smoke canister 140 g
1 x	PCARD Wireless System
1 x	AX-60 starters (5 pcs)
1 x	Initior Receiver FRX2 Wireless
1 x	Smoke set "Glider"
1 x	B4-0 rocket charges (6 pcs)
1 x	"S" set for planes
1 x	3l Smoke oil
1 x	White smoke canister 140 g
1 x	"S" set for boats
2 x	Red smoke canister 140 g
1 x	White smoke bombs AX-60 (5 pcs)
2 x	Blue smoke canister 100 g
1 x	Initior Transmitter FTX2 Wireless
1 x	Electric rocket starters (6 pcs)
1 x	Green smoke canister 65 g
1 x	Ventral support for AX-18/AX-60
1 x	Remote electric ignition system
2 x	White smoke canister 100 g
1 x	Mixers smoke bombs AX-60 (5 pcs)
1 x	Green smoke canister 140 g
2 x	Green smoke canister 100 g
1 x	Smoke set "M"
1 x	AX-60 starters (5 pcs)
1 x	White smoke bombs AX-3 (10 pcs)
1 x	Plastic caps for AIR BURTS (30 pcs)
1 x	Parachute expulsion foam
1 x	Black smoke bombs AX-60 (5 pcs)
1 x	Smoke set "S"
1 x	Pine wood slat 5.0x5.0x1000 mm
1 x	Liston HAYA 10 x 10 x 1000 mm
1 x	Hard aluminium thin-walled tube with fibreglass case ø30x1mm, 1m
3 x	BALSA triangular 15x15x1000 mm
1 x	Mahogany wood slat 1.5x1.5x1000 mm
1 x	Trailing edge BALSA 35x8x1000 mm
2 x	Pine wood slat 10x10x1000 mm
1 x	BALSA trip 3.0x5.0x1000 mm
1 x	Pine wood slat 1.5x3.0x1000 mm
2 x	Walnut wood slat 3.0x3.0x1000 mm
1 x	BALSA triangular 6x6x1000 mm
1 x	Walnut wood slat 1.5x1.5x1000 mm
1 x	BALSA trip 8.0x8.0x1000 mm
2 x	Pine wood slat 3.0x7.0x1000 mm
1 x	Aluminum Bayonet / strongal D12 mm / 0.5 m
1 x	Aluminum Bayonet / strongal D25 mm / 1 m
2 x	BALSA trip 10x10x1000 mm
1 x	Pine wood slat 2.0x2.0x1000 mm
1 x	BALSA trip 2.0x10.0x1000 mm
1 x	Linden wood slat 3.0x3.0x1000 mm
1 x	BALSA trip 6.0x6.0x1000 mm
1 x	Beech dowels 2.0 x 1000 mm
2 x	BALSA leading edge 8x10x1000 mm
1 x	Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm
1 x	Walnut wood slat 2.0x2.0x1000 mm
3 x	OBECHI sheet 2.0x3.0x1000 mm
1 x	Mahogany wood slat 2.0x2.0x1000 mm
1 x	Aluminium cap bolt washer M3 red (8 pcs)
1 x	Quicklock washer 2.5 mm (10 pcs)
1 x	M3-M4 rubber washer (8 pcs)
1 x	SE Ring 400 mm (2 pcs)
1 x	Motor DLE 200cc Premium Muffler
1 x	Oracover Orange 2 m
1 x	Extension S-Bus 1-2 silicon 120 cm FUTABA
1 x	Futaba Female 40 cm extension
1 x	Straightened rod Ø 1.5 mm x 1500 mm
1 x	Optical RPM Sensor
1 x	Yellow smoke canister 100 g
2 x	Pine wood slat 6.0x6.0x1000 mm
1 x	BALSA triangular 10x10x1000 mm
2 x	Pine wood slat 3.0x10.0x1000 mm
1 x	Linden wood slat 2.0x2.0x1000 mm
1 x	Beech dowels 10 mm x 1000 mm
1 x	A/C quality beech plywood 600x300x0.6 mm
1 x	Birch plywood plate 600x300x2.0 mm
1 x	Beech dowels 4.0 x 1000 mm
1 x	A/C quality beech plywood 1520x750x3.0 mm
2 x	Birch plywood plate 600x300x4.0 mm
1 x	Birch plywood plate 600x300x1.2 mm
1 x	Retract undercarriage for gliders 3-7 Kg 3.8-4.3 (without wheel)
1 x	Wheel cover holder Ø 5 mm (2 uds)
1 x	A/C quality beech plywood 1520x750x4.0 mm
1 x	Lite Plywood panel 600x300x3.0 mm
1 x	Air pressure gauge
1 x	A/C quality beech plywood 600x300x0.8 mm
1 x	Y-Hose connector 3-3-3 mm
1 x	Retract undercarriage for gliders 12-25 Kg 2-2.8 (without wheel)
1 x	Tailwheel for 20/60 size
1 x	Quick hose connector 3-3 mm
1 x	Y-Hose connector 4-4-4mm
1 x	Birch plywood plate 600x300x2.5 mm
1 x	Birch plywood plate 600x300x3.0 mm
1 x	A/C quality beech plywood 600x300x6.0 mm
1 x	Tail wheel for 8-12 kg models
1 x	Wheel collar 2 mm Ø (4 uds)
1 x	Axle wheel with accesories
1 x	Angled clevis with threaded rod M3
1 x	A/C quality beech plywood 600x300x0.8 mm
1 x	Tap FESTO 6-6 mm
1 x	Lite Plywood panel 600x300x2.0 mm
1 x	Birch plywood plate 600x300x1.5 mm
1 x	Check valve quick hose connector 4-4 mm
1 x	A/C quality beech plywood 600x300x5.0 mm
1 x	Balsa panel 10x100x1000 mm
1 x	M3 Maxi ball link (2 uds)
1 x	Brake for 140 mm wheels
1 x	DPS Switch JR/JR
1 x	POWER PEAK D7 EQ-BID 12V/230V-Duo Charger
1 x	3.2 mm Prop Adapter M6
1 x	14 mm Portholes for screws (10 pcs)
1 x	250 mm / 16 mm Airbrakes
1 x	Power Pack SE Series JETCENTRAL
1 x	Propeller POWER-PROP 7x7
1 x	Crystal RX 35.120 Ch 72
1 x	Motor mount EDGE 540 48"
1 x	Cooler motor type 300
1 x	Crystal TX 35.100 Ch 70
1 x	Albatros ,spare fuselage (Top Model)
1 x	ARTIST 1.560 mm

7,796.13EUR