47.90EUR

Servo GO-1023MG 7.0 kg.cm 0.09s/60º
[KAV201023MG]


Very strong and thin (10mm) programmable digital micro servo 23g with metal gears and wide range of supply voltage (4,8-8,4V), 2xBB, ideal for ailerons and flaps of gliders. 4.5kg.cm torque, 0.14s/60° speed at 4.8V, 5.2kg.cm torque, 0.12s/60° speed at 6.0V, 6.5kg.cm torque, 0.10s/60° speed at 7.4V. Aluminum servo case for perfect cooling under high load

Very powerful programmable digital micro servo with steel gears and with output shaft mounted on two ball bearings for use in RC models of all types. Thanks to its flat servo case with height of 10 mm, it is particularly suitable for controlling ailerons and flaps in RC glider models with thin wing profiles. The servo is housed in an aluminium case for perfect cooling even under high loads.With the help of the USB programmer/interface for GO servos and the PC operator program you can program a wide range of servo parameters (servo end-points, servo reverse and neutral position, overload protection, soft start, fail-safe, etc.).
Programmable functions
Servo angle: Used to set the maximum travel of the servo. Default setting is approx. 120° at normal control pulse width range (900~2100 µs); approx. 180° at maximum allowed control pulse width range (500~2500 µs).
Servo Neutral: Used to set the neutral (center) position of the servo.
Damping Factor: Sets the servo's stopping behavior characteristic.
PWM Power: Sets the output power of the servo. As higher the value is, the faster the servo is and the more thrust it has - of course, the current draw will be proportionally higher. Range: 39.2~100%
Sensitivity: Adjusts the sensitivity (insensitivity bandwidth) of the servo. The higher the value - the narrower the insensitivity bandwidth - the servo will only move if the change in control signal width is greater than the insensitivity bandwidth. Setting the sensitivity value too high can cause the servo to oscillate in some applications. Range: Ultra High (Extra High - sensitivity bandwidth approx. 1 µs) - High (High - approx. 2 µs) - Medium (Medium - approx. 3 µs) - Low (Low - approx. 4 µs)
Soft start: Enables/disables the soft start function. This function prevents the servo from abruptly moving into the operating position after power is turned on, thus reducing the risk of damage to the servo gears.
Inversion: Reverses the sense of servo movement.
FUTABA SR mode: Used only with FUTABA RC system working in SR mode. Do not turn this option on if you are using a different FUTABA RC system setting or any other brand of RC system.
SANWA SSR mode: Used only with SANWA RC system working in SSR mode. Do not turn this option on if you are using a different SANWA RC system setting or any other brand of RC system.
Fail-safe: If the control signal from the receiver is completely lost or if the servo cannot detect the signal properly (e.g. due to interference), the servo may enter one of three fail-safe modes:
(a) Free: Fail-safe is disabled.
(b) Maintain Position: the servo maintains the position corresponding to the last correctly received signal.
(c) Transition to neutral: The servo returns to the neutral (1500 µs pulse width) position.
Overload protection: enables or disables servo overload protection in three levels - once the overload has lasted for a preset time (in seconds), the servo output power is limited to the corresponding preset value (in % of max power).
Reset: Restores the connected servo to its factory default settings.
Extended supply voltage 4.8-7.4 V (nominal).Output shaft with 25 teeth.
Servo dimensions Micro
Servo type Digital
Thrust at 4.8V [kg/cm] 4.5
Thrust at 6.0V [kg/cm] 5.2
Thrust at 7.4V [kg/cm] 6.5
Thrust at 8.4V [kg/cm] 7
Speed at 4.8V [s/60st.] 0.14
Speed at 6.0V [s/60st.] 0.12
Speed at 7.4V [s/60st.] 0.1
Speed at 8.4V [s/60st.] 0.09
Servo gears Metal
Ball bearings 2×
High-voltage Yes
Power supply [V] 4.8 - 8.4
Length [mm] 30
Width [mm] 10
Height [mm] 30.5
Weight [g] 23
Intended for Aeroplanes


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x Hovercraft sailcloth
1 x Servo NARO Max Std
1 x BOX-Setup Actro-marine
1 x Landing gear Rocket 400
2 x P 17×5.8 Prop-2PCS/PAIR
1 x Kwik link AL M3 con Clip (2 pcs)
1 x Ball Link ALU M3 - RH (1 pcs)
1 x GLOW 2C + accesories
1 x Complete kit CAT 966G II WEDICO-construction-models
1 x 
1 x Aluminium coupler M3/2 with ball bearing (1 pcs)
1 x Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x Aluminium coupler M2,5/2 with ball bearing (1 pcs)
1 x Ball link Aluminio M3 (2 pcs)
1 x BETA 1400 ARF Red
1 x Conector MT-60 (pair)
1 x Universal Charging Lead - 500mm - 4mm to Glow Plug Igniter
1 x Glow Plug Clip 1.3 Ah
1 x Ciano KAVAN Medium 20g
2 x Propeller RABOESCH M4 70 mm (5 Blades) (Left)
1 x Waterproof adhesive tape, width 19mm, length 25m
1 x Glow starter with charger 230v
1 x 10 mm aluminium spinner (Kavan)
1 x Battery LiPo GRE18 600 mAh 7.4v
1 x Pin hinge 26x11 mm (10 uds)
1 x Opto Gas Engine Kill Switch
1 x RCEXL Electronic ignition twin CM-6
1 x Landing gear strap small (4 uds)
1 x Landing gear axle Ø 4 mm (2 uds)
1 x Body for landing gear Ø 4 mm
1 x Festo Adaptor Tygon Large/4mm
1 x T-Hose connector 3-3-3 mm
1 x Faucet FESTO
1 x Wheel cover holder Ø 5 mm (2 uds)
1 x Landing gear retract neumatic (Jet Legend)
1 x Landing gear strap medium (4 uds)
1 x Y-Hose connector 4-4-4mm
1 x Z-shaped servo mount
1 x Body for landing gear Ø 3 mm
1 x Wheel cover holder Ø 6 mm (2 uds)
1 x Metal ring front FEMA
1 x Tap FESTO 4-4 mm
1 x LA500 tail empennage
1 x 2000A 12V Lithium Jump Starter with 150PSI Air inflator
1 x Dust collector for mould cleaning
1 x Oils Pumps Empty (1 liter)
1 x Xplorer4 anemometro
1 x Propeller CFK 18,5x12
1 x Ball link Aluminio M3 x 3 x 5 x 18mm (6 uds)
1 x Propeller CFK 17x18
1 x Propeller CFK 12.75x13
1 x Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x Propeller CFK 12.5x6.5
1 x Head core bushing
1 x Raer wall
1 x Helices DJI Mavic Air STEALTH "Black" (4x Ud)
1 x Steering lever
1 x Propeller set 400 (2R+2L)
1 x Propeller CFK 18x16
1 x 48 mm cylidric hinge Ø 2,5 mm (5 pcs)
3 x Round Rod 1.0x3.5 cm
2 x Pulley brass 6/1,5 (2 pcs)
2 x Fully Threaded Steel Rod M2,5 (2 uds)
1 x Metal ball clevis M3 (10 uds)
1 x Dummy motor GPW Wasp Scale 1/4
1 x Lipo KAVAN 2200 mAh 11.1v 30/60C
1 x Extension 15 cm (Futaba)
1 x Servo GO-1035MG 16 kg.cm 0.08s/60º
1 x Turnbuckle M1,6x20/30 (2pcs)
1 x Cable coupler M2x66 (2 uds)
1 x Porta Kwik link M4 4 mm (2 pcs)
1 x Porta Kwik link M4 3 mm (2 pcs)
1 x BRASS CONTROL HORN M3x16 mm 2pcs
1 x 4 mm M3 red control terminal (4 pcs)
1 x wire tensioner (blue)
1 x Turnbuckle M3 33x49 (2pcs)
1 x Cable coupler M2 (10 uds)
1 x Turnbuckle M1,6x17/27 (2pcs)
1 x wire tensioner (black)
1 x Pull-Pull complet set with CF rudder double servo arm
1 x Cable coupler M3 (10 uds)
1 x Wire easy tensioner (silver)
1 x Pulley brass 8/2 (2 pcs)
1 x Cable coupler M2,5 (2 pcs)
1 x Cable coupler M3 (10 uds)
1 x Lipo KAVAN 2200 mAh 11.1v 40/80C
1 x Recess mount-rem. glow plug set
1 x Rubber Insert soft, 1 Pcs.
1 x Cable coupler M2 (10 uds)
1 x Swashplate metal LAMA
1 x SIG Coverall 1.2x4.5 m
1 x Stainless steel 4 m Pull-Pull complet set (max 20 kg)
1 x wire tensioner (red)
1 x Set clevis for pull-pull (TY13233 & TY13234)
1 x Turnbuckle M2,5x27/43 (2pcs)
1 x Turnbuckle M2x22/35 (2pcs)
1 x wire tensioner (silver)
1 x Threaded coupler M2,5 (10 pcs)
1 x Pulley brass 4/1,5 (2 pcs)
1 x Pulley brass 14/2 (2 pcs)
1 x Pulley brass 2,5/1 (2 pcs)
1 x Turnbuckle M2x29/43 (2pcs)
1 x Lipo KAVAN 5000 mAh 11.1v 40/80C
1 x Spinner 60 mm White (Kavan)
1 x Spinner 40 mm Black (Kavan)
1 x Gasket electric Fuel Pump
1 x Window mounting channel 5m
1 x GRE-18 RTR Crawler 1:18 Blue
1 x Maxi Fuel Filter
1 x Debonder CA 20g
1 x 25 mm Sandpaper file
1 x T-shape holder metal LAMA
1 x Superlight standard wheel 100 mm (2 pcs)
1 x Superlight deluxe wheel 75 mm (2 pcs)
1 x Servo GO-12S70MG 20.5kg.cm 0.06s/60º
7,242.18EUR
Manufacturers
Manufacturer Info
Kavan
Other products
Languages
Español English
Currencies