Top » Catalog » Kavan » KAV201023MG

47.90EUR

Servo GO-1023MG 7.0 kg.cm 0.09s/60º
[KAV201023MG]

Very strong and thin (10mm) programmable digital micro servo 23g with metal gears and wide range of supply voltage (4,8-8,4V), 2xBB, ideal for ailerons and flaps of gliders. 4.5kg.cm torque, 0.14s/60° speed at 4.8V, 5.2kg.cm torque, 0.12s/60° speed at 6.0V, 6.5kg.cm torque, 0.10s/60° speed at 7.4V. Aluminum servo case for perfect cooling under high load

Very powerful programmable digital micro servo with steel gears and with output shaft mounted on two ball bearings for use in RC models of all types. Thanks to its flat servo case with height of 10 mm, it is particularly suitable for controlling ailerons and flaps in RC glider models with thin wing profiles. The servo is housed in an aluminium case for perfect cooling even under high loads.With the help of the USB programmer/interface for GO servos and the PC operator program you can program a wide range of servo parameters (servo end-points, servo reverse and neutral position, overload protection, soft start, fail-safe, etc.).
Programmable functions
Servo angle: Used to set the maximum travel of the servo. Default setting is approx. 120° at normal control pulse width range (900~2100 µs); approx. 180° at maximum allowed control pulse width range (500~2500 µs).
Servo Neutral: Used to set the neutral (center) position of the servo.
Damping Factor: Sets the servo's stopping behavior characteristic.
PWM Power: Sets the output power of the servo. As higher the value is, the faster the servo is and the more thrust it has - of course, the current draw will be proportionally higher. Range: 39.2~100%
Sensitivity: Adjusts the sensitivity (insensitivity bandwidth) of the servo. The higher the value - the narrower the insensitivity bandwidth - the servo will only move if the change in control signal width is greater than the insensitivity bandwidth. Setting the sensitivity value too high can cause the servo to oscillate in some applications. Range: Ultra High (Extra High - sensitivity bandwidth approx. 1 µs) - High (High - approx. 2 µs) - Medium (Medium - approx. 3 µs) - Low (Low - approx. 4 µs)
Soft start: Enables/disables the soft start function. This function prevents the servo from abruptly moving into the operating position after power is turned on, thus reducing the risk of damage to the servo gears.
Inversion: Reverses the sense of servo movement.
FUTABA SR mode: Used only with FUTABA RC system working in SR mode. Do not turn this option on if you are using a different FUTABA RC system setting or any other brand of RC system.
SANWA SSR mode: Used only with SANWA RC system working in SSR mode. Do not turn this option on if you are using a different SANWA RC system setting or any other brand of RC system.
Fail-safe: If the control signal from the receiver is completely lost or if the servo cannot detect the signal properly (e.g. due to interference), the servo may enter one of three fail-safe modes:
(a) Free: Fail-safe is disabled.
(b) Maintain Position: the servo maintains the position corresponding to the last correctly received signal.
(c) Transition to neutral: The servo returns to the neutral (1500 µs pulse width) position.
Overload protection: enables or disables servo overload protection in three levels - once the overload has lasted for a preset time (in seconds), the servo output power is limited to the corresponding preset value (in % of max power).
Reset: Restores the connected servo to its factory default settings.
Extended supply voltage 4.8-7.4 V (nominal).Output shaft with 25 teeth.
Servo dimensions Micro
Servo type Digital
Thrust at 4.8V [kg/cm] 4.5
Thrust at 6.0V [kg/cm] 5.2
Thrust at 7.4V [kg/cm] 6.5
Thrust at 8.4V [kg/cm] 7
Speed at 4.8V [s/60st.] 0.14
Speed at 6.0V [s/60st.] 0.12
Speed at 7.4V [s/60st.] 0.1
Speed at 8.4V [s/60st.] 0.09
Servo gears Metal
Ball bearings 2×
High-voltage Yes
Power supply [V] 4.8 - 8.4
Length [mm] 30
Width [mm] 10
Height [mm] 30.5
Weight [g] 23
Intended for Aeroplanes

few units

Reviews

Quick Find

Shopping Cart

1 x	AL Axle Shaft 4.0x16 mm (2 uds)
1 x	Landing gear axle Ø 4 mm (2 uds)
1 x	Landing gear axle Ø 6 mm (2 uds)
1 x	Landing gear axle 4x21 4 mm (2 uds)
1 x	Oracover ROYAL RED 2m
1 x	Oracover CHROME 2m
2 x	Oracover Brown 2 m
2 x	Papel japones 12 grs/m2 760x510 mm JAPICO
2 x	Ply-Span 450x600/13g White
1 x	Oracover Azul Cielo 2 m
1 x	Oratex Natural White 2m
1 x	Oracover Yellow CUB 10 m
1 x	Ply-Span 450x600/13g Blue
2 x	Ply-Span 450x600/13g Yellow
1 x	Oracover Yellow CADMIO 10 m
1 x	Oracover Azul 2 m
2 x	Ply-Span 450x600/13g Red
1 x	ORACOVER transparent Yellow (10 m)
2 x	Ply-Span 450x600/13g Orange
1 x	Oratex Natural White 20m
1 x	Oracover Black 2 m
1 x	Oratex Silver 2m
1 x	Oratex Red Fokker 10 m
1 x	Oracover Yellow CUB 2 m
1 x	Monokote BLUE metalizado (1.8x0.65m)
1 x	ORACOVER Fluor red (2 m)
1 x	Oracover CARBON Metalic 1 m
1 x	MYLAR film A350 (1000x500 mm)
1 x	Oracover Orange 2 m
1 x	Monokote BLANCO jet (1.8x0.65m)
1 x	Screw-lock pushrod conn snap Ø 1.5 mm (2 uds)
1 x	Crimping sleeves for cable 1.3 mm (10 pcs)
2 x	Steering arm 12 mm Ø 3 mm (2 uds)
1 x	Cap closure 33/23.5mm (2 uds)
1 x	Covered closure or fairings
2 x	SUS wire 3m (nylon coated)
2 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
2 x	Micro screw-lock pushrod conn snap Ø 1 mm (2 uds)
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	Steering arm 16 mm Ø 4 mm
1 x	Stainless steel cable Ø 0.5 mm (10 m)
1 x	Vertical cockpit anchor "tipe F3A" (2 pcs)
2 x	Canopy Latch
1 x	Stainless steel cable Ø 0.5 mm (20 m)
2 x	Crimping sleeves for cable 0.85 mm (10 pcs)
1 x	Stainless steel cable Ø 0.5 mm (2 m)
2 x	Screw-lock connector M2 (2 uds)
2 x	Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x	White silicone 0,25 qmm wire (150 m)
1 x	PVC 0,25 qmm 4 line servos wire JR/Graupner (5 m)
1 x	Ball link Aluminio M3 x 3 x 5 x 18mm (6 uds)
1 x	Threaded coupler ALU M2,5 Ø 6 (2 uds)
2 x	Cable servo PREMIUM MAXI 10m (blanco/rojo/azul) PVC
1 x	Crimping sleeves for 1.1 mm cable (10 pcs)
2 x	100m servo "Premium" wire (white/red/blue)
1 x	Cable servo PREMIUM MAXI 50m (blanco/rojo/azul) PVC
1 x	Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x	Threaded coupler M2,5 Ø 2 mm (10 pcs)
2 x	Silicone 0,50 qmm servos wire Futaba (100 m)
1 x	Clevis plastico I=26 mm / hole 2mm / pin 1 (2 pcs)
1 x	Silicone 0,35 qmm servos cable Futaba (5 m)
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	Black silicone 0,25 mm² wire (25 m)
1 x	Ball link Aluminio M3 (6 uds) 27x11.9x5.9 mm
1 x	Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x	Cable servo PREMIUM MAXI 200m (blanco/rojo/azul) PVC
1 x	Couple M4 for wire (10 pcs)
3 x	PVC 0,08 qmm Graupner servos wire (5 m)
1 x	Ball link duraluminium M3 V1 (10 pcs)
1 x	Z type of cable coupler Ø 2 (2 uds)
1 x	Silicone 0,35 qmm servos wire Graupner(100 m)
2 x	5 line servos wire black (1 m)
1 x	Threaded coupler ALU M3 Ø 6 (2 uds)
1 x	Silicone 0,50 qmm servos wire Graupner(5 m)
1 x	Solvent Plasti Dip 1000 ml
2 x	Painting GHT Lexan Black 150 ml
1 x	1000 ml sealer (DOPE)
2 x	Universal Colour Paste white 50 g
1 x	Premium servo extension 50cm
1 x	Extension S-Bus 1-2 silicon 120 cm FUTABA
1 x	Shirt Hispano Aviación
1 x	Extension silicon 30 cm male (Graupner)
1 x	Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x	Cable S.BUS 3 salidas 300 mm
1 x	Cable silicona female batt. receptor 30 cm (Futaba)
2 x	Cable silicona macho batt. receptor 30 cm (Futaba)
1 x	Vest clothes Hispano Aviación
1 x	Futaba Female 40 cm extension
1 x	Extension silicon 30 cm male (Futaba)
3 x	Premium servo extension 75cm
2 x	Extension 30 cm (Futaba)
2 x	Premium servo extension 100cm
2 x	Circlick securite
1 x	Extension PVC 150 cm (Graupner)
1 x	servo adapter lead, JST-SH socket - JR male Pin, for GR-12SH+HoT
1 x	Extension silicon 100 cm (Futaba)
1 x	Futaba Female 40 cm extension
1 x	Tape GFK 50 mm
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 180 GRIT (5 pcs)
1 x	Vacuum Connection VA 1 (for hose Ø 6 mm)
1 x	Starter 12v (Max 90 and 15ccm)
1 x	Strip ABS 2.0x8.0x1000 mm
2 x	PVC yellow-orange transparent battery termo-retract 57 mm (1 m)
1 x	PVC blue transparent battery termo-retract 68 mm (10 m)
2 x	6,4x1000 mm 2:1 black termoretract tube
2 x	PVC transparent battery termo-retract 195 mm (1 m)
1 x	12,7x1000 mm 2:1 green termoretract tube
1 x	PVC yellow transparent battery termo-retract 68 mm (1 m)
1 x	Wheel collar 5 mm Ø (4 uds)
1 x	Locking cable tie 3.2x142 (uds)
1 x	Stainless steel cable Ø 1.3 mm (10 m)
1 x	Press fitting for 0,5 diam. steel cable (10 pcs)
1 x	Pushrod greyline 3/2 with coupler M2 L: 1000 mm
1 x	Triple rod con. 3mm Pushrod (2 pcs)
1 x	Steering arm 12 mm Ø 4 mm
2 x	Snap long M2 (10 uds)
1 x	Locking cable tie 4.6x203 (uds)
1 x	Fully Threaded Steel Rod M3
1 x	Snap for floding prop for 2 mm axi
1 x	Steering arm 16 mm Ø 4 mm (2 uds)
1 x	Steering arm 16 mm Ø 3 mm (2 uds)
1 x	Pushrod octagone 4/3
2 x	Lead with adhesive (2 pcs)
1 x	Wheel collar 3 mm Ø (4 uds)
2 x	Steering arm 16 mm Ø 3 mm
2 x	Stainless steel cable Ø 0.62 mm (10 m)
1 x	Crimping sleeves for cable 0.70 mm (10 pcs)
1 x	38x4,5 mm wires output (2 pcs)
1 x	Spinner plastic black fixed propeller 30 mm
1 x	Extension silicon 30 cm female (Graupner)
1 x	Extension silicon 100 cm (Graupner)
2 x	Cable silicona macho batt. receptor 30 cm (Graupner)
1 x	Split pin 1x8 mm (10 uds)
2 x	Steering arm 12 mm Ø 4 mm (2 uds)
1 x	Falcon Carbon Spinner 82mm for electric motor
2 x	Spinner Alumin. fixed propeller 45 mm / 3,2 mm
1 x	Silicone black 1,5 qmm wire ( 1 m)
2 x	Cabel PVC 2 x 0.25 mm2 (5 m) red-black
1 x	Silicone red 6,0 qmm wire ( 1 m)
1 x	Spinner NUT M5
1 x	Spinner Alumin. fixed propeller 45 mm / 5,0 mm
1 x	Plasti Dip Liquid Tape 429 ml black
1 x	F3A carbon 95 mm spinner
1 x	Silicone black 6,0 qmm wire ( 1 m)
1 x	PVC 0,08 qmm Futaba servos wire (5 m)
1 x	Silicon red 1,0 qmm cable ( 25 m)
1 x
1 x	JR silicone servo wire 0,35 qmm / 5m
1 x	Spinner NUT 1/4x28
1 x	Silicone red 4,0 qmm wire ( 1 m)
1 x	51 mm INO spinner (carbon imitation)
1 x	Spinner NUT M5
1 x	Silicone black 1,0 qmm wire ( 25 m)
1 x	PARTALL® Hi-Temp Wax, 340 g
1 x	Spinner Alumin. fixed propeller 45 mm / 6,0 mm
1 x	Silicone red 1,0 qmm wire (100 m)
1 x	Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
1 x	Spinner INO 63 mm Chrome (Imitacion metal)
1 x	Silicone black 0,75 qmm cable ( 1 m)
1 x	Hovercraft sailcloth
1 x	102 mm INO spinner (carbon imitation)
1 x	Spinner Alumin. fixed propeller 45 mm / 4,0 mm
1 x	F3A carbon 75 mm spinner for Hacker C-50
1 x	Carbon fiber rod 7.0 mmx1000 mm
2 x	Extension silicon 10 cm (Graupner)
1 x	0,14 mm PVC servo wire extension, ZH micro conector.
1 x	Cabel "Y" 30 cm (graupner)
2 x	Extension lead 15 cm Multiplex
2 x	Extension 100 cm (Futaba)
2 x	Premium servo extension 25cm
2 x	USB Interface Adapter
2 x	PVC transparent battery termo-retract 85 mm (1 m)
1 x	2,4x1000 mm 2:1 black termoretract tube
2 x
1 x	Cable coupler M2 (10 uds)
1 x	Blade holder metal LAMA
1 x	Battery LiPo GRE18 600 mAh 7.4v
2 x	Ball Link M2 with Ball and Hardware, 10 pcs
1 x	3,2x1000 mm 2:1 red termoretract tube
2 x	1,2x1000 mm 2:1 red termoretract tube
1 x	4,8x1000 mm 2:1 red termoretract tube
1 x	Ply-Span 450x600/13g Black
1 x	1,6x1000 mm 2:1 red termoretract tube
1 x	37 mm PVC transparent battery termo-retract (1 m)
1 x	1,6x1000 mm 2:1 black termoretract tube
1 x	6,4x1000 mm 2:1 blue termoretract tube
1 x	2,4x1000 mm 2:1 red termoretract tube
1 x	1,2x1000 mm 2:1 black termoretract tube
1 x	165 mm PVC transparent battery termo-retract 165 mm (1 m)
1 x	105 mm PVC transparent battery termo-retract 68 mm (1 m)
1 x	PVC termo-retract battery 45 mm black transparent (1 m)
1 x	58 mm PVC transparent battery termo-retract 68 mm (1 m)
1 x	2,4x1000 mm 2:1 green termoretract tube
1 x	68 mm PVC transparent battery termo-retract 68 mm (1 m)
1 x	PVC transparent battery termo-retract 51 mm (1 m)
1 x	4,8x1000 mm 2:1 blue termoretract tube
2 x	Actuador lineal HLS12-100210-7.4v
1 x	Cabel charger transmitter GRAUPNER
1 x	50 mm aluminium spinner (Kavan)
1 x	Birch plywood plate 600x300x1.2 mm
1 x	Ciano KAVAN Thick 20g
1 x	60 mm aluminium spinner (Kavan)
1 x	Debonder CA 20g
2 x	Conector MR-60 (pareja)
2 x	Combo KAVAN PRO 3542-1150 + KAVAN PRO-80 SB
1 x	Adaptadores carga 6s JST-XH
1 x	150 mm inflatable superlight deluxe wheel (2 pcs)
1 x	Brazo servo KAVAN doble aluminio 25T - 2.5" M3
1 x	Ball Bearing Oil 25 ml
1 x	Ciano KAVAN Super Thin 20g
1 x	Combo KAVAN PRO 3536-1000 + RAY 40 SB
1 x	BETA 1400 ARF Red
1 x	Tip wing protector 28x10x12 (2 pcs)
1 x	Landing gear frontal support 29x26x13,5
1 x	Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
1 x	Split M1,2x10 (10 pcs)
1 x	Wing bolts M3 Steel screw blue (2 pcs)
1 x	Wing bolts M3 Steel screw Red (2 pcs)
1 x	Cable grommet Ø 4 mm (4 uds)
1 x	Cockpit plastic closing
1 x	Tip wing protector 30x10 (2 pcs)
1 x	Allen wheel collar M3x3
1 x	Split pin 1.6x16 mm (10 uds)
1 x	28x5 mm wires output (2 pcs)
1 x	Allen wheel collar M4x6
1 x	Cable set PREMIUM, fuselage/wing
1 x	Spinner propeller pleg. 40 mm / 3,0 mm
1 x	Aluminium Hub for folding Props 55 mm M8 Shaft 6 mm
2 x	6 mm Quick clamp_S (10 pcs)
1 x	Cabel "Y" 30 cm (Futaba)
1 x	20 g tin paste
1 x	Hobbylite Filler, Balsa colour
1 x	Spinner Alumin. fixed propeller 50 mm / 4,0 mm
1 x	4,8x1000 mm 2:1 black termoretract tube
1 x	Universal Colour Paste deep black 50 g
1 x	Spray EC Red 400ml
1 x	Spray adhesive INFUTAC (Clear) 500 ml
1 x	82 mm 12 mm axi 30 g F3A CF drilled spinner
1 x	Spinner INO 89 mm Chrome (Imitacion metal)
1 x	Spinner plastic white fixed propeller 51 mm
1 x	Spray adhesive AEROFIX 2
1 x	Silicone black 0,5 qmm wire ( 25 m)
1 x	PVC 0,14 qmm servo wire Futaba (5 m)
1 x	Spinner propeller pleg. 40 mm / 3,2 mm
1 x	Cable servo PREMIUM 1 m (blanco/rojo/negro) AWG21 + AWG26 TPE
1 x	Silicone 0,35 qmm servos wire Futaba (100 m)
1 x	Cable Cargador FUTABA
1 x	40 mm servo arm with bearing (2 pcs)
1 x	LightBox SR
1 x	TMM 2512-3S heli
1 x	Silicone black 0,75 qmm wire ( 25 m)
1 x	Servo GO-13 MG 13g 2.8 Kg 0.12s/60º
1 x	Recess mount-rem. glow plug set
1 x	Program Card KAVAN ES
1 x	Servo GO-1013 MG 3.8kg
1 x	Servo GO-09 9g
1 x	SAVAGE Max Red 1080 mm
1 x	Servo GO-10S41MG 10.5 kg.cm 0.075s/60º
1 x	Prolongador S-Bus JR/JR 20cm
1 x	Futaba male 40 cm extension
1 x	Extension silicon 35 cm male (Futaba)
1 x	Ciano KAVAN Medium 20g
1 x	Servo GO-1088MGW 74 kg.cm 0.125s/60º
1 x	Servo Arm 25T M3 KAVAN 6.5 / 19.6 mm
1 x	Combustible Glow "KAVAN" air/heli 10% nitro
1 x	Pin hinge 34x16 mm (10 uds)
1 x	SIG Coverall 1.2x0.9 m
1 x	Smart Soldering Iron 110W/230V AC
1 x	Combo KAVAN C3536-1250 + KAVANA R50SB +
1 x	55 mm aluminium spinner (Kavan)
1 x	25 mm Sandpaper file
1 x	Cable coupler M3 (10 uds)
1 x	Charger SKY RC e680
1 x	Birch plywood plate 600x300x1.5 mm
1 x
1 x	Ciano KAVAN Thin 20g
1 x	Servo GO-1035MG 16 kg.cm 0.08s/60º
1 x	Conector MT-60 (pair)
1 x	Servo GO-12S69MG 26kg.cm 0.10s/60º
1 x	Program card KAVAN PRO

7,749.27EUR