120.00EUR

Combo KAVAN PRO 3542-1150 + KAVAN PRO-80 SB
[KAV30.1638C]

Combo set of BLS motor with 80A ESC for model aircraft: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 rpm per V, power supply Lixx 3-4s, shaft 5 mm.

Outrunner brushless electric motor for model aeroplanes: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 RPM/V, input voltage 3-4S Lixx. 5.0mm shaft. Alternative designation based on the stator dimension: 2820-1150. KAVAN PRO series motors are high performance 14-pole brushless outrunners. State-of-the-art design, hardened steel shafts, high quality ball bearings, High grade material used for stators and rotors ensure long lifetime and unbeatable performance and high efficiency. KAVAN PRO series motors are low revolution/high torque electric motors capable of swinging large diameter propellers without need for a gearbox.
KAVAN PRO 3542-1150 is a motor for model aeroplanes up to 2200 g all-up weight powered by 3-4S LiPo flight battery pack. It is great for faster 2000-2500 mm electric powered gliders, 1400-1500 mm high wing trainers, scale and aerobatic models.
Motor installation: KAVAN 3542-1150 has been designed both for the front and radial mount installation. Front mount: Use four M3 screws; these may not go deeper than 3-4 mm into the front case. Radial mount: Use four M3 screws to secure the mounting cross to the firewall. The firewall should be made of 4.0-5.0 mm plywood. The radial mount set is supplied with the motor.
The motor set contents: KAVAN PRO 3542-1150 motor w. cables (3.5 mm gold-plated connectors), radial mount set accessories. The full instruction manual can be downloaded here: KAVAN PRO Brushless Motors Instruction Manual
Note: Alternative designation based on the stator dimensions: 2820-1150.
Powering LiXX cells 3 - 4
RPM/V [ot./min/V] 1150
Max. power (180 s) [W] 1000
Internal resistance [mOhm] 16
Open-circuit current (při 10 V) [A] 2.7
Max. peak current (180 s) [A] 70
Diameter [mm] 35.2
Length [mm] 41
Length celková [mm] 63.5
Shaft diameter [mm] 5
Weight [g] 141
Poles count 14
Timing [°] 20 - 25
ESC [A] 70 - 80
Weight of glider (up-to) [g] 2200
Weight of trainer (up-to) [g] 2100
Weight of acrobat (up-to) [g] 1800
Weight of 3D (up-to) [g] 1200
Doporučená vrtule 3S: 11x8"-12x6"
4S: 9x6"-10x5.5”

under request

Reviews

Quick Find

Shopping Cart

1 x	Gates hinge black 30x16 mm (2 pcs)
1 x	Nylon hinge 20x20x0,3 (10 pcs)
1 x	Gates hinge aluminium (1 pcs)
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Nylon hinge 20x15x0,3 (10 pcs)
1 x	67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	Pin type hinge Al 6x98 mm (2 pcs)
1 x	Gates hinge 30x16 mm (2 pcs)
1 x	Pin type hinge Al 3,0x50 mm demount (2 pcs)
1 x	Flap hinge (6 pcs)
1 x	Long pinned hinge (6 uds)
1 x	Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
2 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	Large flex hinge (12 uds)
1 x	Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x	76 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x	Gates hinge
1 x	Fast'n EZ-CA-Hinge, lite (12 uds)
1 x	Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x	Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x	Pin hinge 26x11 mm (10 uds)
1 x	Medium pin type hinge (12 uds)
1 x	15 mm reinforced hinge
1 x	Nylon hinge for flaps 33x9 (2 pcs)
1 x	25 mm reinforced hinge
1 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Nylon hinge 15x0,3 (10 pcs)
1 x	EXTRA NG 74" yello/blue/red (Skywing RC)
1 x	SE Ring 480 mm (2 pcs)
1 x	Brass control horn M4 short for wire (10pcs)
1 x
2 x	LH long aluminium horn L31xH30 (2pcs)
1 x	Servo GO-1035MG 16 kg.cm 0.08s/60º
2 x	6 mm blue aluminium threaded horn with patella
2 x	Turbina KINGTECH K320 G5
2 x	Ring 320 mm length (5 pcs)
1 x	SE Ring 350 mm (2 pcs)
1 x	Horn for flap control (1 pcs)
2 x	Tape GFK 25 mm
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	SE Ring 240 mm (2 pcs)
2 x	Marker ties (20 pcs)
2 x	Tape GFK 50 mm
1 x	Horn 5/20 with M2 Bearing
1 x	RH long aluminium horn (2pcs)
1 x	Horn 13,5x16 mm (2 pcs)
1 x	Threaded coupler ALU M2,5 Ø 6 (2 uds)
2 x	20x1000 mm Ring Strap Back To Back
2 x	Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x	Adaptadores carga 6s JST-XH
1 x	Electric Landing Gear "Black Edition" ULTIMATUM 3.0 (Elektron Re
1 x	Threaded coupler ALU M3 Ø 4 (2 uds)
1 x	Horn 6/20 with M3 Bearing
1 x	Horn 5/10 with M2 Bearing
2 x	Small aluminium horn blue (2pcs)
1 x	Small aluminium horn gold (2pcs)
1 x	Horn with ball 40x30
1 x	20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	Brass control horn M4 short for wire (4 pcs)
1 x	SE Ring 400 mm (2 pcs)
1 x	14x60 mm Mini rings Tie Wraps (4 pcs)
1 x	Brass control horn M2 short for wire (2 pcs)
1 x	Extension MPX-MPX 20 cm
2 x	10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	SE Ring 360 mm (2 pcs)
1 x	SlowFlyer control horn (3 pcs)
1 x	Foil for sticking flaps and ailerons
1 x	Tape GFK 38 mm
1 x	Threaded coupler ALU M2 Ø 4 (2 uds)
1 x	6 mm aluminium horn with patella
3 x	Horn with ball 55x40
1 x	Threaded coupler ALU Left M2,5 Ø 4 (2 uds)
1 x	RUDDOG Protection and Heat Shield Tape (2mx50mm)
1 x	Ball Link Plier
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x	Digital scale up to 40 kg
1 x	2,0x50 mm allen screwdriver
1 x	3,0x60 mm allen screwdriver
1 x	Starter 12v (Max 180 and 30ccm)
1 x	Vacuum pump 12 CFM
1 x	Cut tube
1 x	Dust collector for mould cleaning
1 x	Crimping tool
1 x	2,5x60 mm allen screwdriver
1 x
1 x	1,5x50 mm allen screwdriver
1 x	Vacuum pump P1-N
1 x	Crimping tool
1 x
1 x	PROXXON - SILICON CARBIDE BELTS FOR BSL 220/E
1 x	Starter EM Gear Power 250
1 x	One touch canopy lock
1 x	Canopy Lock V1 M3 Red (2 pcs)
1 x	Covered closure or fairings
1 x	Cap closure 33/23.5mm (2 uds)
1 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Stainless steel cable Ø 0.5 mm (20 m)
1 x	Steering arm 16 mm Ø 3 mm (2 uds)
1 x	Crimping sleeves for cable 0.70 mm (10 pcs)
1 x	ABS angle 6,0x6,0x1000 mm
1 x	Towing hook
1 x	L-Connector 4.0 mm x 1000 mm
1 x	Steel tube (L 1000 mm Ø3 mm, Ø2,7 mm)
1 x	Flap hinge 33x9 mm (6 pcs)
1 x	AX-60 starters (5 pcs)
1 x	Flat washer 4.3 mm (20 pcs)
1 x	Walnut wood slat 2.0x2.0x1000 mm
1 x	EC5-Set male, simple quality, 2 x female pin, 1 x blue housing
1 x	Mobile Terminal
1 x	Nylon hinge for flaps/gates 27x10,5 (2 pcs)
2 x	Short extra-strong control horn with bearing 2,8x15
1 x	Sistema LDS - Ø12 mm servos Ø 6/25 spline 60º (Futaba) pitch 5 m
1 x	USB Adaptor OPTronics
1 x	Cierre cabina aluminio Ø4, I=10 mm
1 x	5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Rudder forward 70x28 "type Kato"
1 x	Battery RX JETI LiIon RB 3100 7.2v
1 x	Long horn 50x26
1 x	Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 6 mm
1 x	PowerPack 2.5X2 PRO
1 x	Propeller POWER-PROP 14x9 Izda
1 x	Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 4 mm
1 x	Sistema LDS - Ø12 mm servos Ø 6/25 spline 60º (Futaba) pitch 7 m
1 x	LH long black aluminium horn L31xH30 (2pcs)
1 x	Horn 16,5x20 mm (2 pcs)
1 x	Duralumium F3A horn 30x10x23,5 mm (2 pcs)
1 x	Horn mando small (2 pcs)
1 x	Cable with accesories
1 x	Threaded coupler ALU Left M2,5 Ø 3 (2 uds)
1 x	Short adjustable control horn 3x24
1 x	GP 15 JETA
1 x	Propeller drill jig DA-35/50/60/70
1 x	Fox MDM 1 4000 mm DeLuxe,wing joiner
1 x	Handle for PERMAGRIT lime
1 x	Fresa corte diamante Ø 2.35mm (flame)
1 x	LUNAK 4,00 m
1 x	Sandpaper file 13 mm
1 x	PROXXON - SAW BLADE DIAMOND OZI/E
1 x	Goma arrancador Ø36 mm x 30 mm

19,658.62EUR