120.00EUR

Combo KAVAN PRO 3542-1150 + KAVAN PRO-80 SB
[KAV30.1638C]

Combo set of BLS motor with 80A ESC for model aircraft: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 rpm per V, power supply Lixx 3-4s, shaft 5 mm.

Outrunner brushless electric motor for model aeroplanes: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 RPM/V, input voltage 3-4S Lixx. 5.0mm shaft. Alternative designation based on the stator dimension: 2820-1150. KAVAN PRO series motors are high performance 14-pole brushless outrunners. State-of-the-art design, hardened steel shafts, high quality ball bearings, High grade material used for stators and rotors ensure long lifetime and unbeatable performance and high efficiency. KAVAN PRO series motors are low revolution/high torque electric motors capable of swinging large diameter propellers without need for a gearbox.
KAVAN PRO 3542-1150 is a motor for model aeroplanes up to 2200 g all-up weight powered by 3-4S LiPo flight battery pack. It is great for faster 2000-2500 mm electric powered gliders, 1400-1500 mm high wing trainers, scale and aerobatic models.
Motor installation: KAVAN 3542-1150 has been designed both for the front and radial mount installation. Front mount: Use four M3 screws; these may not go deeper than 3-4 mm into the front case. Radial mount: Use four M3 screws to secure the mounting cross to the firewall. The firewall should be made of 4.0-5.0 mm plywood. The radial mount set is supplied with the motor.
The motor set contents: KAVAN PRO 3542-1150 motor w. cables (3.5 mm gold-plated connectors), radial mount set accessories. The full instruction manual can be downloaded here: KAVAN PRO Brushless Motors Instruction Manual
Note: Alternative designation based on the stator dimensions: 2820-1150.
Powering LiXX cells 3 - 4
RPM/V [ot./min/V] 1150
Max. power (180 s) [W] 1000
Internal resistance [mOhm] 16
Open-circuit current (při 10 V) [A] 2.7
Max. peak current (180 s) [A] 70
Diameter [mm] 35.2
Length [mm] 41
Length celková [mm] 63.5
Shaft diameter [mm] 5
Weight [g] 141
Poles count 14
Timing [°] 20 - 25
ESC [A] 70 - 80
Weight of glider (up-to) [g] 2200
Weight of trainer (up-to) [g] 2100
Weight of acrobat (up-to) [g] 1800
Weight of 3D (up-to) [g] 1200
Doporučená vrtule 3S: 11x8"-12x6"
4S: 9x6"-10x5.5”

under request

Reviews

Quick Find

Shopping Cart

1 x	BALSA triangular 10x10x1000 mm
2 x	Balsa panel 1.5x100x1000 mm
1 x	Beech dowels 4.0 x 1000 mm
1 x	Beech dowels 2.0 x 1000 mm
2 x	BALSA triangular 15x15x1000 mm
2 x	A/C quality beech plywood 600x300x0.6 mm
2 x	BALSA trip 4.0x4.0x1000 mm
1 x	Balsa panel 2.5x100x1000 mm
2 x	Balsa panel 4.0x100x1000 mm
2 x	Balsa panel 5.0x100x1000 mm
2 x	Balsa panel 6.0x100x1000 mm
2 x	BALSA trip 3.0x3.0x1000 mm
2 x	BALSA trip 5.0x5.0x1000 mm
2 x	Balsa panel 10x100x1000 mm
2 x	BALSA trip 2.0x2.0x1000 mm
1 x	Birch plywood plate 600x300x4.0 mm
1 x	Beech dowels 3.0 x 1000 mm
3 x	Balsa panel 3.0x100x1000 mm
3 x	Balsa panel 1.0x100x1000 mm
2 x	Straightened rod Ø 6.0 mm x 1000 mm
2 x	Straightened threaded rod M3 - 1m
2 x	Straightened rod Ø 4.5 mm x 1000 mm
1 x	Straightened rod Ø 2.0 mm x 1000 mm
1 x	Brass rod Ø 1.0 mm x 1000 mm
1 x	Brass hexagonal rod Ø 3 mm x 1000 mm
2 x	Straightened rod Ø 5.5 mm x 1000 mm
1 x	Brass rod Ø 1.5 mm x 1000 mm
1 x	Brass hexagonal rod Ø 5 mm x 1000 mm
1 x	Straightened threaded rod M2-1m
2 x	Straightened rod Ø 2.5 mm x 1000 mm
1 x	Straightened rod Ø 0.5 mm x 1000 mm
1 x	Straightened rod Ø 0.8 mm x 1000 mm
1 x	Straightened rod Ø 1.2 mm x 1500 mm
1 x	Straightened rod Ø 1.0 mm x 1000 mm
2 x	Brass rod Ø 0.5 mm x 1000 mm
1 x	A/C quality beech plywood 600x300x5.0 mm
2 x	BALSA triangular 6x6x1000 mm
1 x	Birch plywood plate 600x300x3.0 mm
1 x	quality beech plywood BIRCH 600x300x2.0 mm
1 x	Balsa panel 8.0x100x1000 mm
2 x	A/C quality beech plywood 1520x750x4.0 mm
2 x	A/C quality beech plywood 1520x750x3.0 mm
2 x	A/C quality beech plywood 600x300x6.0 mm
3 x	800TVL CMOS camera for FPV
1 x	Birch plywood plate 600x300x2.0 mm
1 x	Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 3m
1 x	Carbon fibre tape 200 g/m² (unidirectional) 50 mm
1 x	Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x	Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x	Demoulding wedge red (40 x 20 mm) 5 pcs
1 x	Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 50M
1 x	Carbon roving DowAksa / 24k / 1600 tex
1 x	Carbon fabric 160 g/m² (twill weave) 127 cm, roll/ 10 m
1 x	Carbon Non-Woven, 160 g/m² 127 cm 5m
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x	Carbon Non-Woven, 160 g/m² 100 cm 10 m
1 x	Carbon Non-Woven, 160 g/m² 127 cm 1 m
1 x	Glass fabric tape 225 g/m² (Silane, plain) 30 mm X 100m
1 x	Carbon Non-Woven, 160 g/m² 100 cm 5m
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	Spring lock washer 2.6 mm (20 pcs)
1 x	Flat washer 4.3 mm (20 pcs)
1 x	Fast'n EZ-CA-Hinge (12 uds)
1 x	Circlik for shaft 1.2 mm (10 pcs)
1 x	Circlik for shaft 1.5 mm (10 pcs)
1 x	Spring lock washer 4.1 mm (20 pcs)
1 x	Aluminium cap bolt washer M4 blue (8 pcs)
1 x	Aluminium wide washer M3 gold (4 pcs)
1 x	Spring lock washer 2.1 mm (20 pcs)
1 x	Aluminium cap bolt washer M4 green (8 pcs)
1 x	Aluminium wide washer M4 Red (4 pcs)
1 x	Aluminium cap bolt washer M4 red (8 pcs)
1 x	Aluminium wide washer M4 Black (4 pcs)
2 x	Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x	Quicklock washer 1.5 mm (10 pcs)
1 x	Lock washer 4.3 mm (20 pcs)
1 x	Sandwich carbon + poplar 3mm + carbon 480x290 mm
1 x	Propeller POWER-PROP 14x9
1 x	Propeller POWER-PROP 14x9 Izda
1 x	Extension silicon 30 cm male (Graupner)
1 x	Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x	Futaba male 40 cm extension
1 x	Extension silicon 100 cm (Futaba)
1 x	Extension silicon 100 cm (Graupner)
1 x	Extension 7.5 cm
1 x	Cabel "Y" 15 cm
1 x	Prolongador S-Bus JR/JR 10cm
1 x	Pine wood slat 2.0x10.0x1000 mm
1 x	BALSA leading edge 8x10x1000 mm
1 x	Futaba Female 40 cm extension
1 x	Extension lead 15 cm Multiplex
2 x	BALSA trip 6.0x6.0x1000 mm
1 x	Circlick securite
2 x	Walnut wood slat 3.0x3.0x1000 mm
1 x	Extension silicon 35 cm male (Futaba)
1 x	Cable silicona macho batt. receptor 30 cm (Futaba)
1 x	Extension silicon 10 cm (Graupner)
1 x	0,14 mm PVC servo wire extension, ZH micro conector.
2 x	OBECHI sheet 2.0x3.0x1000 mm
2 x	Linden wood slat 2.0x2.0x1000 mm
1 x	Premium servo extension 75cm
2 x	BALSA trip 8.0x8.0x1000 mm
1 x	Pine wood slat 6.0x6.0x1000 mm
1 x	Prolongador S-Bus JR/JR 20cm
1 x	Liston HAYA 8 x 8 x 1000 mm
2 x	Pine wood slat 3.0x10.0x1000 mm
1 x	Premium servo extension 25cm
1 x	Extension 15 cm (Futaba)
3 x	Pine wood slat 3.0x7.0x1000 mm
1 x	BALSA trip 3.0x5.0x1000 mm
1 x	Premium servo extension 50cm
1 x	Cable S.BUS 3 salidas 100 mm
1 x	Extension silicon 30 cm female (Graupner)
2 x	Pine wood slat 3.0x5.0x1000 mm
1 x	Pine wood slat 5.0x5.0x1000 mm
1 x	Cabel "Y" 30 cm (Futaba)
1 x	Carbon fiber flat 1000x3.0x1.0 mm
1 x	Glases Nimbus
1 x	Spray EC Red 400ml
1 x	Vacuum Connection VA 1 (for hose Ø 6 mm)
1 x	Militarian pilot "Fly Boy" size 9cm (Slimline)
1 x	Z Bender - S Type Tool
1 x	Short ball link M3 (6 uds)
1 x	Aluminium coupler M2,5/2 with ball bearing (1 pcs)
1 x	SE Ring 240 mm (2 pcs)
1 x	A/C quality beech plywood 600x300x0.8 mm
1 x	Crystal Universal RX 35.090 Ch 69
1 x	Crystal TX 35.150 Ch 75
1 x	Cargador para AA/AAA Ni-MH & Ni-Cd
1 x	Crystal RX 35.120 Ch 72
1 x	Straightened rod Ø 7.0 mm x 1000 mm
1 x	Straightened rod Ø 1.5 mm x 1000 mm
2 x	BALSA trip 10x10x1000 mm
1 x	A/C economy plywood 600x300x6+.0 mm
1 x	A/C quality beech plywood 600x300x0.8 mm
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x	A/C quality beech plywood 600x300x8.0 mm
1 x	Pine wood slat 1.5x3.0x1000 mm
1 x	Fiberglass plate 620x540x0,3 mm
2 x	BALSA trip 2.0x10.0x1000 mm
1 x	Breatex™ Non-woven absorber 300 g/m² Roll 41 m
1 x	200 mm extensión servo HITEC/JR
1 x	Glass fabric 425 g/m² aero,10x1m
1 x	Peel ply 100 g/m² (plain weave) 50 cm x 2m
1 x	Carbon plate 550x350x3.0 mm ECOTECH
1 x	Sheet Depron Aero 1250x800x3 mm
1 x	Connectors MPX 8 pins (green) 1 pair (male-female)
1 x	MR30 connector male
1 x	Sandwich Carbon fibre Rohacell (800 x 280 x 3 mm)
1 x	Breatex™ Non-woven absorber 150 g/m² Roll 5 m
1 x	Glass fibre sleeve Ø 20 mm X 20m
1 x	Liston HAYA 10 x 10 x 1000 mm
1 x	Breatex™ Non-woven absorber 150 g/m² Roll 20m
1 x	SD HC 8 GB
1 x	Small flex hinge (12 uds)
1 x	150 Newtons FEMA absorber
1 x	Unmounted aluminium pin 6x98 mm (2 pcs)
1 x	100 Newtons FEMA absorber
1 x	Small pinned hinge (6 uds)
1 x	200 Newtons FEMA absorber
1 x	Motor SAITO FG-61 TS
1 x	Mahogany wood slat 3.0x3.0x1000 mm
1 x	BALSA triangular 8x8x1000 mm
1 x	45 mm aluminium spinner (Kavan)
1 x	Dummy motor GPW Wasp Scale 1/4
1 x	Axle for AXI 28269/xx motors

5,084.33EUR