419.00EUR

ZENOAH ZG 62 SL
[TC6500]

ZENOAH ZG 62 SL

In 1990 Komatsu reworked the cylinder specially for model aircraft purposes this S cylinder had the transfer passages altered as well as the combustion chamber. This resulted in an increase of 200 rpm in the 6,500 range. Fit a tuned pipe and the rpm is considerably increased, giving a power of 6,6 hp at 8,400 rpm.

The crankshaft is a hefty piece of forged steel, induction hardened, with a diameter of 15 mm and supported in two large ballraces, the conrod is a forged unit also induction hardened with caged roller bearings both ends, the gudgeon pin is hollow. There are two thin pegged rings. The ignition unit consists of two separate coils, both fixed to the side of the motor causing no interference with the cooling air. The standard Walbro pump carburettor is fitted with a choke.

The very wide and cleanly formed cooling fins allow the use of large propellers causing the motor to turn at relatively low speeds. For aerobatic aircraft like our CAP 21 the 22x10" or the 22x12" Menz S propeller has proved to be very good. Our big Tiger flies best with the 24x10". If you wish to, or must, reduce the noise still further, then you can pull the intake air out of the fuselage by fitting a 90 degree bend between the carburettor and motor. The intake noise is louder than the noise from the standard silencer. This bend by lengthening the intake tract allows the fitting of a 24x12" or 26x10" Menz S propeller, of course you are not going to get the maximum power from the motor by this method, but you have more than enough power to fly our big Tiger with the 62?s throttle set at just a rather fast tickover.

The lowest possible noise level in flight with lots of power is obtained with our Hydro-Mount-System, coupled with the Stainless steel silencer, sucking the intake air out of the fuselage and fitting a Super Silence 21x12" Carbon 3-blade propeller at 6,300 rpm. For higest performance use the Super Silence 24x10" Carbon 2-blade prop. It produces 130 N static thrust at 6500 rpm.

The ZG 62 SL is delivered complete with silencer, fitted with 40 mm prop hub, but without motormount.

Specifications:
Capacity: 62 cc
Bore: 47,5 mm
Stroke: 35 mm
Power: 4,3 hp
with tuned pipe: 6,6 hp
Weight: 2040 g without silencer and engine mount

under request

Reviews

Quick Find

Shopping Cart

1 x	Truck-trailer for gliders 720 x 285 mm
1 x	Propeller balancer
1 x	Surface Indicator Gauge Small
1 x	Angle measurer
1 x	Field folding model stand SebArt
1 x	Medidor ángulos y/o incidencias
1 x	Truck-trailer for gliders 720 x 239 mm
1 x	Angle of incidence meter
1 x	Propeller balancer
2 x	Strip 2,5x1,25x330 mm
1 x	ABS Strip 1.5x3.0x1000 mm
2 x	ABS Strip 1.0x4.0x1000 mm
2 x	Round Rod 4,0x1000 mm
2 x	ABS Strip 1.0x3.0x1000 mm
2 x	Strip ABS 2.0x3.0x1000 mm
1 x	Strip 1,5x1,5x330 mm
1 x	Servo NARO Max Std
1 x	Carbon fiber rod 12 mm x 1000 mm
1 x	Carbon fiber rod 1.5 mm x 1000 mm
1 x	Carbon fiber rod 7.0 mmx1000 mm
1 x	Carbon fiber rod 4.0 mmx1000 mm
1 x	Carbon fiber rod 10 mm x 1000 mm
2 x	Carbon fiber rod 0.5 mmx1000 mm
1 x	Carbon fiber rod 1.0 mm x 1000 mm
1 x	Carbon fiber rod 0.5 mmx1000 mm
1 x	Carbon fiber rod 2.0 mmx1000 mm
1 x	Carbon fiber rod 1.5 mm x 1000 mm
1 x	Carbon fiber rod 8.0 mmx1000 mm
1 x	Carbon fiber rod 6.0 mmx1000 mm
2 x	Squared carbon wing joinner 5x5x220 mm
1 x	Carbon fiber flat 1000x3.0x1.0 mm
2 x	Carbon fiber rod 20 mmx1000 mm
1 x	Carburetor for ZG45SL and ZG62/S/SL
1 x	Motor Mount for TITAN ZG45 and ZG62, length 36 mm
1 x	Motor Mount for TITAN ZG45 and ZG62, length 54 mm
2 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x	Piston ring for DA-50R and DA-100
1 x	Tufnol Choke Lever Arm d=4,7mm
1 x	BOSCH spark plug cap for ZG 26SC/SCM, 231SLH, G230RC
1 x	Carburador DA-35, DA-50R-DA-100L , VM-60/70
1 x	Crimping sleeves for cable 0.70 mm (10 pcs)
1 x	‎Reed valve for DA-60/70
1 x	Stainless steel cable Ø 0.62 mm (10 m)
1 x	Pick up DA50/100/150
1 x	20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Spring clamp for tube Ø50 mm
1 x	Piston ring for ZG 26SC/EI, ZG 26SCM ZG 26SLH and Zenoah G260RC/
1 x	DA 85 / DA 100 / DA 100 L carburetor
1 x	3,9 mm ZG20-ZG38 servo arm
1 x	13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Civilian pilot "Curt" size 9cm (Slimline)
1 x	BALSA trip 2.0x2.0x1000 mm
1 x	Ball link M2 (10 pcs)
1 x	M2 5Diam black ball link V2 (2 pcs)
1 x	Carbon tube (L 1000 mm, Ø16 mm, Ø12 mm)
1 x	Fixed launching hook
1 x	Long pinned hinge (12 uds)
1 x	Battery LiPo GENS 5300 mAh 2S 7.4V 30C (Gens Ace)
1 x	Battery Lipo GENS 4000 mAh 7.4v TX
1 x	Battery LiPo GENS 2600 mAh 2S 7.4v Transmitter Pack (Gens Ace)
1 x	Battery LiPo GENS 450 mAh 2S 7.4V 25C (Gens Ace)
1 x	Battery LiPo GENS 5300 mAh 4S 14.8V 30C (Gens Ace)
1 x	Battery LiPo GENS 5000 mAh 3S 11.1v 45C (Gens Ace)
1 x	Battery LiPo GENS 2200 mAh 4S 14.8v 25C (Gens Ace)
1 x	Battery LiPo GEN2700 mAh 3S 11.1v Transmitter Pack (Gens Ace)
1 x	Battery LiPo GENS 4000 mAh 6S 22.2v 25C (Gens Ace)
1 x	Spring Clip Ø25 mm
1 x	Round Rod 1,25x1000 mm
1 x	Strip ABS 2.0x5.0x1000 mm
2 x	120x60 mm SLH KOVO wheel
1 x	Carbon fiber rod 0.8 mmx1000 mm
1 x	Carbon fiber rod 2.5 mmx1000 mm
2 x	Hovercraft sailcloth
1 x	Carbon fiber rod 14 mmx1000 mm
1 x	Carbon fiber rod 5.0 mmx1000 mm
1 x	Carbon fiber rod 3.0 mm x 1000 mm
1 x	Stainless Steel Tuned Pipe for engines from 45 to 80 cc
1 x	Gasket for motor DA 50
1 x	Spring Clip 25 mm teflon tube
1 x	Tygon tube 7.94 x 4.7 mm 15 m
1 x	Gasket, insulator ZG 20
1 x	Crimping sleeves for 1.1 mm cable (10 pcs)
1 x	Fixing Ring with Base 60 mm
1 x	Prop hub for DA-100, DA-100L
1 x	Gasket carburettor/insulator for ZG 38/S/SC
1 x	Gasket, cylinder base for motor DA 50
1 x	Dia. 25x5 mm tefon tube for escape
1 x	ZG231cc SHL
1 x	ZENOAH G270RC
1 x	Screw for mounting plate of DA100/120
1 x	EDGE 540-A 74" (1880 mm)
1 x	EXTRA NG 85" 2159mm yellow/blue
1 x	SLICK 360-A 104" (2640 mm)
1 x	LASER 260 60" V2 ARF Yellow (SkyWing)
1 x	EDGE 540-A 91" (2310 mm)
1 x	LiIon Battery 3000 mAh 3.3v 15A (2 pcs)
1 x	Battery RX JETI LiIon RB 5200 7.2v
1 x	Strip ABS 2.0x10.0x1000 mm
1 x	Round Rod 1,5x1000 mm
1 x	Adapters for 7.5 - 35cc aircraft and naval engines
1 x	Round Rod 1,0x1000 mm
1 x	Round Rod 3,0x1000 mm
1 x	Set freno para ruedas Dia. 127 mm
1 x	Servo arm with 4 mm hole to FEMA 9810A
1 x	Battery RX JETI LiIon RB 2600 7.2v
1 x	Aluminun wheel collar 3 mm Ø (4 uds)
1 x	Aluminun wheel collar 2 mm Ø (4 uds)
1 x	Crystal Universal TX 35.140 Ch 74
1 x	Wheel FEMA 90 mm / 6 mm
1 x	Cierva C30 Elevator
1 x	Cierva C30 simulated motor
1 x	ZENOAH ZG 26SLH Helicopter Engine
1 x	3-blades 29x12 carbon prop Super Silence
1 x	Intake tube with flange and 2 M5x60

7,605.35EUR