Top » Catalog » PowerBox Systems » POWER4620

379.00EUR

PowerBox Cockpit SRS (incl. SensorSwitch)
[POWER4620]

Features:
- SRS – Serial Receiver System provides the ability to use receivers with a serial interface, such as those made by Spektrum DSM2 and DSMX, Multiplex M-LINK, Futaba S-BUS and Jeti R_SAT.
- For Spektrum and Jeti satellites, Futaba S-BUS Multiplex M-LINKand HoTT receivers
- All channels from the receiver are transferred using a three-core lead
- Complete receiver redundancy, double the security
- Complete battery redundancy: two batteries, two electronic switches, redundant output voltage with dual regulation
- Spektrum with four satellites, Futaba with two S-Bus receivers, Multiplex with two M-Link receivers, HoTT, Jeti with two satellites
- High-resolution graphic OLED screen with 128 x 64 pixels
- Ultra-simple menu-based programming using the SensorSwitch
- Eleven channels + one channel for door sequencer
- Downlink channel transmission for Spektrum and MPX
- Unrestricted channel assignment for all output sockets, (channel output mapping)
- Synchronised servo outputs for totally simultaneous servo movements
- Four-stage user-variable servo frame rate (9ms, 12 ms, 15 ms, 18 ms, 21 ms)
- Integral freely programmable door sequencer
- The unit saves receiver data, such as "lost frames" and "failsafes", for all connected receivers - whether Spektrum, Futaba, Multiplex, Jeti. Data can be read out after the flight on the OLED screen
- Four match-channels for two servos each; both servos individually variable
- 16-bit processor for high-speed, high-resolution signal processing
- Signal amplification for a total of 12 channels and 21 servos
- Direct transmission of battery voltages and capacities to the transmitter (downlink channels)
- On-screen voltage display for each battery separately, with bar indicator
- Residual capacity display for both batteries separately
- User-variable servo voltage: choice of 5.9 V or 7.4 V
- Minimum value memory shows any voltage collapses
- Large-area heat-sink for high regulator capacity
- Regulator monitor and regulator error indicator
- Supports three battery types: LiPo, LiIon, NiMH / NiCd, LiFePo
- Suppression of any servo feedback currents which might occur

Specification:
- Operating voltage: 4,0 Volts to 9,0 Volts
- Power source:
    2 x two-cell LiPO batteries 7,4 Volts
    2 x five-cell NiCd or. NiMH batteries
    2 x two-cell LiFePo batteries (A123)
- Current drain:
    switched on - approx. 130 mA
    switched off - approx. 15 µA
- Dropout voltage: approx. 0.25 V
- Max. receiver and servo current: 2 x 3 A (stabilised) according to cooling , Peak 2 x 20 A
- Servo signal resolution: 0,5 µs
- Signal repeat rate: 9 ms, 12 ms, 15 ms, 18 ms, 21 ms (frame rate)
- Screen: OLED 128 x 64 pixels, graphic
- For: Spektrum, Futaba, Multiplex, Jeti, HoTT.
- Servo sockets: 21 Sockets, 12 channel
- Temperature range: - 30 °C to + 75 °C
- Dimensions: 110 x 72 x 24 mm
- Weight: 115 g
- SensorSwitch: 15 g
- EMV approval: EN 55014-1:2006
- CE approval: 2004/108/EG
- WEEE Reg. No.: DE 639 766 11

temporarily out of stock

Reviews

Quick Find

Shopping Cart

2 x	Extractor piñones 2.3/3.2 mm
2 x	Nylon hinge 20x20x0,3 (10 pcs)
1 x	Flap hinge 33x9 mm (6 pcs)
1 x	76 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	Long pinned hinge (6 uds)
1 x	Gates hinge
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	Long pinned hinge (12 uds)
1 x	Pin type hinge Al 4,5x70 mm (2 pcs)
1 x	67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x	Fast'n EZ-CA-Hinge, lite (12 uds)
2 x	Nylon hinge 20x15x0,3 (10 pcs)
1 x	Miniature brass strap hinge, 1 m
1 x	Gates hinge aluminium (1 pcs)
1 x	18 mm reinforced hinge
1 x	Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x	Large flex hinge (12 uds)
1 x	Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x	Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
1 x	Small pinned hinge (12 uds)
1 x	Fast'n EZ-CA-Hinge (12 uds)
1 x	67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	Gates hinge black 30x16 mm (2 pcs)
1 x	Nylon hinge for flaps/gates 27x10,5 (2 pcs)
1 x	48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
1 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	15 mm reinforced hinge
1 x	Nylon hinge for flaps 33x9 (2 pcs)
1 x	Ferrita con funda
1 x	Ferrita 27x14x7 mm
3 x	2000A 12V Lithium Jump Starter with 150PSI Air inflator
1 x	Ply-Span 450x600/13g White
1 x	M2,5 5Diam metal ball link V3 (2 pcs)
1 x	Ply-Span 450x600/13g Blue
1 x	Ball Link Plier
1 x	Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x	Parachute BACKUP X100
1 x	Servo KST HS08A Wing Servo - 5.2Kg.cm 0.11s 11.0g 8mm
1 x	Servo KST BLS815 HV V2.0 Servo 20mm 70g 20Kg
1 x	Brazo servo aluminio KST 25T-5V2,3515,325,125,135,145X10,X12,A13
2 x	HITEC 17 mm servo arm with ball link HITEC
2 x	Futaba 14/20 mm servo pull-pull double arm with ball link
2 x	Servo MKS HV6120H
2 x	DYNAMOMETER S-1580
1 x	Brazo servo aluminio 1.25/1.5" Futaba/MKS/Savox
2 x	Servo DITEX TD2612S
1 x	Servo FUTABA BLS 272SV
1 x	Servo FUTABA S 3071 HV S-Bus
1 x	Servo FUTABA BLS173 SV
2 x	SERVO S9177SV HV S-Bus2 Programable
1 x	Servo FUTABA S 9670 SV
1 x	Z-shaped servo mount
1 x	Futaba S3010 Servo - Standard BB 0.16s/6.5kg
2 x	Servo FUTABA HPS-A700 Digital S-Bus
1 x	ALU servo arm 3 mm shaft
2 x	Servo NARO Max Std
2 x	DPSI Micro - RCS
2 x	Spring clamp for tube Ø50 mm
1 x	Pitts Muffler kit for CAP 21
1 x	Junta humo metalica G61 (DLE55RA/DLE61/DLE120)
2 x	Junta humo metalica G35 DLE35
2 x	Junta humo metalica G30 (DLE30/DLE60)
1 x	Anchor of tow Met. 60 mm
2 x	LO 100 Scale 1:2 - Modellbau Bruckmann
1 x	Liferaft 47 mm
1 x	Fox MDM 1 4000 mm Std.
1 x	La Capitania di Venetia accesories
1 x	ASW 20 5000 mm with winglets (Airwold)
1 x	75 mm
2 x	Futaba 30 mm servo arm with M3 ball link
2 x	Ball link M3 (10 pcs, flat ball)
2 x	Futaba 46 mm servo arm with ball link
1 x	6 mm ball link M3 (10 pcs)
2 x	Futaba 20 mm servo arm
1 x	Fully Threaded Steel Rod M2,5 (2 uds)
1 x	Ball Link M2 with Ball and Hardware, 10 pcs
1 x	Ball link duraluminium M3 V1 (10 pcs)
1 x	4 mm M3 red control terminal (4 pcs)
1 x	Angled clevis with threaded rod M3
1 x	Cable coupler M2 (10 uds)
1 x	Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
1 x	Brass ball links BS M3 V1 (10 pcs)
1 x
1 x	170x54 mm SLH KOVO wheel with bearing and metal hub
1 x	DPSI V-Match
1 x	1/12 Pilot "Langley"
1 x	DPSI Micro SingleBat 5.9V/7.2V magnetic switch
1 x	115x29 mm (4.50") Type jets aluminium core wheel
1 x	110x55 mm C SLH KOVO wheel
1 x	Quadcopter Q50 Kit Carbon Fiber
1 x	20x200 mm battery rings
1 x	Servo-V-Limiter 5.2V
1 x	200 mm extensión servo HITEC/JR
1 x	Motor Eachine Racer 250 Brushless Motor - BG2204 2300kv - CCW th
1 x	Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
2 x	External LED's (2 pcs)
1 x	Extension MPX-MPX 20 cm
1 x	VIPER 1.7 Tailpipe + Fuel Tank 1500ml
1 x	VIPER JET G2 Esq. 5 Green/White/Blue
1 x	VIPER JET G2 Esq. 2 Red/White/Silver
1 x	VIPER 1.7 Electric break wheels + structure
1 x	Silicone 0,35 qmm servos wire Graupner(100 m)
2 x	Servo DITEX EL0510M
1 x	Adapter lead MPX/EC3
1 x	Extension for SensorSwitch 30cm
1 x	Conector JR Servo male (10 pcs)
1 x	Extension for LC-Display 50cm
1 x	30 cm DEANS female connector
1 x	Cable servo PREMIUM MAXI 10m (blanco/rojo/azul) PVC
1 x	10m servo "Premium" wire (white/red/blue)
1 x	5 line servos wire black (1 m)
1 x	30 cm MULTIPLEX female connector
1 x	Cable servo PREMIUM MAXI 100m (blanco/rojo/azul) PVC
1 x	Dean "T" - Futaba Adapter
1 x	100m servo "Premium" wire (white/red/blue)
1 x	200m servo "Premium" wire (white/red/blue)
1 x	PowerBox Smokepump JETs 2x outside
1 x	Servo FUTABA SBL 471 SV
1 x	Stick coupler Ms 15 mm
2 x	ASW 15 5000 mm (Airwold)
2 x	Fox MDM 1 4000 mm DeLuxe,Panel instrument Fox MDM 4m
1 x	Servo BLS-M55B 61.2kg
1 x	Servo FUTABA S 3072 HV S-Bus
1 x	Servo FUTABA BLS 276SV
1 x	Futaba BLS255/272/471SV - Gear Set
2 x	Futaba 38 mm servo arm
1 x	Savox Highvoltage Brushless Servo SB-2272MG (Tail rotor)
1 x	Aluminium coupler M3/2 with ball bearing (1 pcs)
1 x	Aluminium red ball links M3 V1 (10 pcs)
1 x	SAVOX SH 0255 MG servo
1 x	Savox Brushless Servo SC-1251 MG
1 x	Crimping sleeves for 1.1 mm cable (10 pcs)
1 x	Clevis plastico I=45 mm / hole 3mm / pin 1 (2 pcs)
1 x	Walnut wood slat 2.0x2.0x1000 mm
2 x	Ball link Aluminio M3 (6 uds) 27x11.9x5.9 mm
1 x	Clevis plastico I=26 mm / hole 2mm / pin 1 (2 pcs)
1 x	Ka-8b ELECTRIC 6000 mm ARF 1:2.5 (Phoenix Models)
1 x	Fox MDM 1 4000 mm DeLuxe,Fundas deLuxe
1 x	GP 15 JETA
1 x	LO 100 ARC 3.3m
1 x	ASH 31 Mi Scale:1/3 - 7m, elevator
1 x	Elevator VENTUS 2cx 4.5m
1 x	Propeller AERO-NAUT M4 50 mm (4 Blades Right
1 x	Propeller 3BL 50 mm M4 Plastic
1 x	Marco de medición doble 35 mm (2 pcs)
1 x	5 mm M2 variable horn
1 x	6 mm hexagonal ball link M3 (10 pcs)
1 x	Hitec 46 mm servo arm with ball link
1 x	Horn 6/35 with M3 Bearing
1 x	6 mm M3 variable horn
1 x	Futaba 30 mm servo rounded arm
1 x	Hitec 30 mm servo rounded arm
1 x	Indoor hinge with servo arm integraded
1 x	HITEC 20 mm servo arm with ball link
1 x	XTorque CFK Servohebel 38
2 x	Turnbuckle M1,6x20/30 (2pcs)
1 x	wire tensioner (black)
2 x	Turnbuckle M2,5x27/43 (2pcs)
2 x	Threaded coupler ALU M3 Ø 6 (2 uds)
2 x	Z type of cable coupler Ø 1.8 (2 uds)
2 x	wire tensioner (silver)
2 x	Rubber bushing with bracket "B" type (2 pcs)
2 x	Turnbuckle M3 33x49 (2pcs)
1 x	Stainless steel 3 m Pull-Pull complet set (max 20 kg)
2 x	wire tensioner (blue)
1 x	DPSI RV Mini 6 Magic with Gas-Cap switch
1 x	Starter 12v (Max 90 and 15ccm)
1 x	Servo SAVOX SV-0236 MG HV
1 x	Savox Brushless Servo SC-1267 SG
1 x	Pine wood slat 6.0x6.0x1000 mm
1 x	Locking cable tie 3.2x142 (uds)
1 x	Carbon Non-Woven, 160 g/m² 127 cm 5m
1 x	Fox 4000 mm with flaps (Airwold)
1 x	Fournier RF-4D
1 x	Fox MDM-1 ARF 3.5m Orange
1 x	Kobuz 5000 mm (Airwold)
1 x	Fox MDM 1 4000 mm DeLuxe,cabina
1 x	LIBELLE Standard 3.8m D-box H-201
1 x	BLANIK 50 V2 Silver/Orange (SebArt)
1 x	Fox MDM 1 4000 mm DeLuxe
1 x	DG-303 ACRO 3750 mm, winglets
1 x	Fox MDM 1 4000 mm DeLuxe,wing joiner
1 x	DISCUS 2A De Luxe 3.750 mm (Topmodel)
1 x	BLANIK 50 V2 Silver/Blue (SebArt)
1 x	Propeller 4BL 60 mm M4 plastic Right
1 x	Plastic fan 17x48 mm (2 pcs)
1 x	Outboard Aqua-Race 60
1 x	Pilote barandilla 3D/11 mm (10 pcs)
1 x	Bateria LRP 2200-7.2v 6 cell NiMH
1 x	Mounting single stop Ms 10 mm
1 x	Ojos de buey 13x9x6 mm (20 pcs)
1 x	Picas 12 mm (20 pcs)
1 x	Propeller 3BL 30 mm M4 plastic Right
1 x	MG cannon 1.8 cm (5 pcs)
1 x	Pile railing 2D/48 mm (10 pcs)
1 x	Plastic fan 12x35 mm (3 pcs)
1 x	Pile railing 2D/30 mm (10 pcs)
1 x	Molinete / Cabestrante amarre Scale 1:32
1 x	Pilote barandilla 16 mm (10 pcs)
1 x	Metal hook for loading arm, 9mm high, 10 pcs
1 x	Motor Johnson 650 with L base and reducer 1,94:1
1 x	Noray 48 mm (5 pcs)
1 x	Pile railing 2D/16 mm (10 pcs)
1 x	Mounting base Ms 12 mm
1 x	Propeller AERO-NAUT M4 60 mm (3 Blades pr) (Right hydropropeller
1 x	Mahagoni 1.0x100x1000 mm
1 x	Propeller AERO-NAUT M4 45 mm (3 Blades pr) (Left hydropropeller
1 x	Propeller AERO-NAUT M4 50 mm (3 Blades pr) (Right hydropropeller
1 x	Adapter rotula M3
1 x	Futaba 38 mm servo arm with ball link
1 x	17 mm servo arm with ball link DES Graupner
1 x	Futaba 76/92 mm servo pull-pull double arm with ball link
1 x	Hitec 25 mm servo arm with ball link
1 x	Horn 6/27 with M3 Bearing
1 x	Horn 5/20 with M2 Bearing
1 x	Indoor landing gear set
1 x	Vertical mounting servo holder
1 x	Futaba 50/60 mm servo pull-pull double arm with ball link
1 x	Horizontal servo holder
1 x	Futaba 25 mm servo arm with M3 ball link
1 x	Servo safety connector (10 pcs)
1 x	Horizontal mounting servo holder
1 x	Futaba 24/30 mm servo pull-pull double arm with ball link
1 x	Hitec 25 mm servo arm with M3 ball link
1 x	XTorque CFK Servohebel 38 HITEC 25T
1 x	Futaba 52 mm servo arm
1 x	Futaba 17 mm servo arm with ball link HITEC
1 x	Futaba 76/92 mm servo pull-pull double arm with ball link HUB Al
1 x	Horn 6/20 with M3 Bearing
1 x	Hitec 38 mm servo arm
1 x	Horns indoor
1 x	Vertical servo holder
1 x	Cable coupler M2x66 (2 uds)
1 x	FUTABA 20 mm servo arm with ball link
1 x	54 mm Futaba servo arm tandem with ball link
1 x	Indoor motor holder
1 x	Brazo Servo XTorque 52 mm HITEC 25T-6
1 x	Horn 5/10 with M2 Bearing
1 x	Ball link M2 (10 pcs)
1 x	Ball link M2,5 (10 pcs)
2 x	Threaded coupler ALU M2,5 Ø 3 (2 uds)
2 x	Small kwik link (10 pcs)
2 x	Z type of cable coupler Ø 2 (2 uds)
1 x	Round Rod 1.0x3.5 cm
2 x	Threaded coupler Micro M2 Ø 0,8 (10 pcs)
1 x	Turnbuckle M2x29/43 (2pcs)
2 x	Z type of cable coupler Ø 1 (2 uds)
2 x	Stainless steel 4 m Pull-Pull complet set (max 20 kg)
2 x	Turnbuckle M1,6x17/27 (2pcs)
2 x	Turnbuckle M2x22/35 (2pcs)
1 x	Turnbuckle M2,5x32/48 (2pcs)
2 x	Rubber bushing with bracket "A" type (2 pcs)
2 x	Wire easy tensioner (red)
1 x	Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x	White large kwik link (10 pcs)
1 x	wire tensioner (red)
1 x	Threaded coupler ALU M3 Ø 4 (2 uds)
1 x	Wire easy tensioner (silver)
2 x	Threaded coupler M2 (10 uds)
1 x	Set clevis for pull-pull (TY13233 & TY13234)
1 x	Threaded coupler ALU M2,5 Ø 6 (2 uds)
1 x	Threaded coupler M2,5 Ø 2 mm (10 pcs)
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	Threaded coupler M2 (10 pcs)
1 x	Threaded coupler Micro M2 Ø 0,8 mm (10 pcs)
1 x	Threaded coupler M2,5 Ø 3 mm (10 pcs)
1 x	DPSI Micro-DualBat 5.9V / 7.2V MPX-JR
1 x	Fod Guard 94x32 mm
1 x	Hot Glue Stick RED
1 x	Xplorer3 anemometro
1 x	Fod Guard 94x34 mm
1 x	PowerBox MERCURY SR2
1 x	PowerBox Cockpit SRS (incl. SensorSwitch)
1 x	PowerBox Sensor V3 MPX/Jr
1 x	Connectors banna oro 4 mm (M/F)
1 x	Propeller CFK 17x18
1 x	PowerBUS Splitter
1 x	Premium servo extension 75cm
1 x	Hovercraft sailcloth
1 x	Power Box GPS Sensor III
1 x	MicroMatch PowerBox
1 x	Propeller RF CFK 13x7
1 x	Propeller CFK 23x12
1 x	Propeller RF CFK 10x17
1 x	Servo MKS 6100 DS
1 x
1 x	Pulley brass 8/2 (2 pcs)
1 x	PowerBox Spare part magnetic sensor
1 x	PowerBox Signal Amplifier
1 x	PowerBox iGyro SRS + GPS Modul
1 x	PowerBox DigiSwitch V2 MPX/JR
1 x	PowerBox PIONEER incl. microSwitch
1 x	PowerBox MagSensor black connector SRS/Champion
1 x	POWERBOX Magic Jeti Switch

51,350.71EUR