13.90EUR

Epoxy SLOW-CURE™ 30 min (130g)
[BSI205]


If CAs are the cure-all for just about all bonding problems, you may be wondering, "Why do I need epoxy?" One primary reason is price. Epoxy costs are about one fourth that of CA. When large objects are being bonded, economics can be a deciding factor on choice of adhesive. The specific characteristics of epoxies also give them advantages in some applications. All our epoxies are mixed with a 50-50 ratio. Any scrap material or paper scratch pad can be used as a mixing surface. We have found, however, that the plastic tops to coffee cans work best due to their outer border and their flexibility, which allows the unused cured epoxy to be released and thrown away.
Squeeze out equal length beads of the desired amount of epoxy, then mix together thoroughly with a popsicle stick or scrap piece of material. In cold weather, epoxy takes longer to cure (too cold and usually they never fully cure) and becomes more difficult to get out of the bottle, especially if it’s less than 1/2 full. The epoxies can be heated in a microwave oven for about 10 seconds so that they flow easier. The heating process, with the caps off, also releases any moisture that can be absorbed by epoxies. Their shelf life, therefore, is virtually unlimited.
Acetone works as the best solvent for cleaning epoxy from brushes and unwanted surfaces before it cures. If epoxy gets on surfaces that acetone will attack, use isopropyl alcohol. We do not recommend any additives for thinning epoxies due to their effect on curing and overall strength. If thin epoxy is required, either use heat or switch to EX-SLOW™ or FINISH-CURE™. Epoxies bond best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion.
A small amount of CA can be used in strategic locations to hold parts in place while the epoxies cure. The minute designations for epoxies refer to the working time, i.e., the time one has before the epoxies begin to set up after being mixed in a large mass. When spread into thinner layers, the working time in increased significantly (except QUIK-CURE™). Working time decreases approximately 25% at temperatures above 90 degrees F. Don’t panic if your skin comes in contact with either epoxy or CA.
While contact should be avoided, uncured epoxy can be washed from your skin with soap and water. Allergic reactions are rare. Cured epoxy and CA can be peeled off the skin and usually are gone after a full day of normal activity. UN-CURE™ will debond any body parts that get stuck together if a peeling action (never pulling) doesn’t part them.

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.


many units
many units

Reviews

Customers who bought this product also purchased
UHU Por 50ml/40g
UHU Por 50ml/40g

many units
many units

Balsa panel 4.0x100x1000 mm
Balsa panel 4.0x100x1000 mm

many units
many units

BALSA trip 3.0x3.0x1000 mm
BALSA trip 3.0x3.0x1000 mm

many units
many units

Fast'n EZ-CA-Hinge, lite (12 uds)
Fast'n EZ-CA-Hinge, lite (12 uds)

many units
many units

BALSA trip 4.0x4.0x1000 mm
BALSA trip 4.0x4.0x1000 mm

many units
many units

Round flex hinge (12 uds)
Round flex hinge (12 uds)

many units
many units

Categories
* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->
  
  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
    Cianocrylate->
    Epoxy->
      EMC-Vega
      KAVAN
      Loctite
      Resoltech
      Epoxy BSI
      Epoxy R-G
    Resin/Gelcoat
    Glass Bubbles
    Contact adhesive
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Aluminium wide washer M3 red (4 pcs)
2 x Aluminium rod Ø 4.0 mm x 3000 mm
1 x Straightened rod Ø 4.5 mm x 1000 mm
1 x Aluminium cap bolt washer M3 black (8 pcs)
1 x Lock washer 4.3 mm (20 pcs)
1 x Straightened rod Ø 8.0 mm x 1000 mm
2 x Circlik for shaft 1.9 mm (10 pcs)
2 x Straightened rod Ø 3.0 mm x 1000 mm
1 x Brass rod Ø 0.5 mm x 1000 mm
2 x Spring lock washer 2.6 mm (20 pcs)
1 x Flat washer 3.2 mm (20 pcs)
1 x Aluminium wide washer M3 blue (4 pcs)
1 x Brass rod Ø 1.5 mm x 1000 mm
1 x Straightened rod Ø 7.0 mm x 1000 mm
1 x Quicklock washer 1.5 mm (10 pcs)
2 x Straightened rod Ø 5.0 mm x 1000 mm
1 x Quicklock washer 1 mm (10 pcs)
1 x Straightened rod Ø 4.0 mm x 1000 mm
2 x Aluminium cap bolt washer M4 green (8 pcs)
1 x Circlik for shaft 1.2 mm (10 pcs)
2 x Straightened rod Ø 1.0 mm x 1000 mm
1 x Brass hexagonal rod Ø 3.5 mm x 1000 mm
2 x Flat washer 2.2 mm (20 pcs)
1 x Spring lock washer 3.1 mm (20 pcs)
2 x M3 black washers (4 pcs)
1 x Quicklock washer 3 mm (10 pcs)
1 x Aluminium cap bolt washer M4 blue (8 pcs)
1 x Quicklock washer 2.5 mm (10 pcs)
1 x Aluminium cap bolt washer M3 green (8 pcs)
1 x Straightened rod Ø 0.5 mm x 1000 mm
1 x Circlik for shaft 2.3 mm (10 pcs)
1 x Flat washer 1.7 mm (20 pcs)
1 x Brass hexagonal rod Ø 3 mm x 1000 mm
2 x Straightened rod Ø 1.5 mm x 1500 mm
1 x Aluminium cap bolt washer M3 red (8 pcs)
1 x Aluminium wide washer M4 Black (4 pcs)
1 x Aluminium cap bolt washer M3 blue (8 pcs)
2 x Aluminium cap bolt washer M4 red (8 pcs)
2 x Lock washer 2.2 mm (20 pcs)
1 x Straightened rod Ø 2.0 mm x 1000 mm
1 x Lock washer 3.2 mm (20 pcs)
2 x Quicklock washer 4 mm (10 pcs)
1 x Brass rod Ø 1.0 mm x 1000 mm
3 x Straightened threaded rod M2-1m
1 x Flat washer 2.7 mm (20 uds)pcs)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 100M
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
1 x Glass fabric tape 225 g/m² (Silane, plain) 40 mm
1 x Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x ARAMID honeycomb 1300x2600x2 mm
2 x Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 50M
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 3m
1 x Vacuum sealing tape, 2.5 x 12 mm (up to 140 °C) 22 roll
1 x Threaded coupler ALU M2 Ø 3 (2 uds)
1 x LH long aluminium horn L31xH30 (2pcs)
1 x Horn 13,5x16 mm (2 pcs)
1 x Cable control set
1 x Horn 6/27 with M3 Bearing
1 x Horn 5/15 with M2 Bearing
2 x Brass control horn M3 short for wire (2 pcs)
1 x Threaded coupler ALU M2,5 Ø 4 (2 uds)
2 x Brass control horn M2 short for wire (2 pcs)
3 x 6 mm red aluminium threaded horn with patella
2 x RH long aluminium horn (2pcs)
1 x Threaded coupler ALU Left M2,5 Ø 4 (2 uds)
1 x 6 mm aluminium horn with patella
1 x Threaded coupler ALU M2 Ø 4 (2 uds)
1 x Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x Horn with ball 40x30
2 x Horn 6/20 with M3 Bearing
1 x SlowFlyer control horn (3 pcs)
1 x Threaded coupler ALU M3 Ø 6 (2 uds)
2 x Threaded coupler ALU M3 Ø 5 (2 uds)
1 x 6 mm blue aluminium threaded horn with patella
2 x Brass control horn M4 short for wire (4 pcs)
1 x 20 mm carbon horn
2 x Horn 6/35 with M3 Bearing
1 x Horn 5/10 with M2 Bearing
1 x Horn for flap control (1 pcs)
2 x LH long black aluminium horn L31xH30 (2pcs)
1 x Threaded coupler ALU Left M3 Ø 4 (2 uds)
1 x 1/6 Pilot "Tony"
1 x Pin type hinge Al 6x98 mm (2 pcs)
1 x Silicone adhesive ELASTOSIL® E4, tube/ 90 ml
1 x 3,2x1000 mm 2:1 black termoretract tube
1 x Conector FUTABA Servo female BLUE silicon (10 pcs)
1 x Hexagonal Nut M2.5 (10 pcs)
2 x Straightened rod Ø 2.5 mm x 1000 mm
1 x Straightened rod Ø 6.0 mm x 1000 mm
1 x Aluminun wheel collar 5 mm Ø (4 uds)
2 x Katana Mini carbon wheel pants (2 pcs)
1 x PVC grid straight 290x185x0.32 mm
1 x Panel Honeycom carbon 350x150x3.5mm
1 x Sandwich carbon + poplar 2mm + carbon 290x160 mm
1 x T-shape holder metal LAMA
1 x Extractor piñones 2.3/3.2 mm
1 x Spring lock washer 4.1 mm (20 pcs)
1 x Sandwich carbon + poplar 3mm + carbon 480x290 mm
1 x Straightened rod Ø 0.8 mm x 1000 mm
1 x Flat washer 4.3 mm (20 pcs)
2 x Spring lock washer 2.1 mm (20 pcs)
1 x Release film 100 cm x 50 m
1 x Medidor ángulos y/o incidencias
1 x Straightened rod Ø 5.5 mm x 1000 mm
1 x Aluminium wide washer M4 Red (4 pcs)
1 x Brass rod Ø 0.8 mm x 1000 mm
1 x Medium extra-strong control horn with bearing 2,8x24
1 x Small aluminium horn blue (2pcs)
1 x Sistema LDS - Ø12 mm servos Ø 6/25 spline 60º (Futaba) pitch 7 m
1 x Long horn 50x26
1 x Flap hinge 33x9 mm (6 pcs)
1 x 67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x Nylon hinge for flaps 33x9 (2 pcs)
1 x Nylon hinge 20x15x0,3 (10 pcs)
1 x 48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x Gates hinge
1 x Medium pin type hinge (12 uds)
1 x Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
1 x 67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x 43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x Long pinned hinge (12 uds)
1 x Nylon hinge 15x0,3 (10 pcs)
1 x 15 mm reinforced hinge
1 x Nylon hinge for flaps/gates 27x10,5 (2 pcs)
1 x Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 5 mm
1 x Short adjustable control horn 3x24
2 x Rudder forward 90x28 "type Kato"
2 x Micro control horn T2 Ø 1
1 x Sistema LDS - Ø12 mm servos Ø 5/24 spline 95º (MKS) pitch 5 mm
1 x Sistema LDS - Ø12 mm servos Ø 5/24 spline 95º (MKS) pitch 6 mm
2 x Long extra-strong control horn with bearing 2,8x34
1 x Threaded coupler ALU Left M2,5 Ø 3 (2 uds)
2 x Horn mando small (2 pcs)
1 x Horn micro type4 Ø 0,5 (2 pcs)
1 x Long adjustable control horn 3x34
1 x Spinner Alumin. fixed propeller 40 mm / 5,0 mm
1 x Tapping Screw M2.9x9.5 (10 pcs)
1 x Pan Head Screw M2x6 PH
1 x Tapping Screw M2.2x9.5 (10 pcs)
1 x Hexagonal Nut M2 (10 pcs)
1 x Hexagonal Nut M3 (10 pcs)
1 x Spinner NUT 1/4x28
1 x Suncover 100cc Red
1 x Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
1 x Sun Cover PC 21 XXL (JMB Jets)
1 x Motor Advance 30-10 F3A
1 x OS 37 SZ-H, Crankshaft
1 x Wheel collar 3 mm Ø (4 uds)
1 x Aluminun wheel collar 2 mm Ø (4 uds)
1 x Wheel collar 4 mm Ø (4 uds)
1 x Brass control horn M2 large for wire (2pcs)
1 x Carbon Non-Woven, 160 g/m² 127 cm 1 m
1 x Carbon roving DowAksa / 24k / 1600 tex
1 x Motor KAVAN PRO 2225-1600
1 x Combo FOXY C3530-570 + FOXY 80 amp
1 x Motor OS 3820-1200 electric
1 x FOXY G2 C3530-700
1 x Motor OS FS 95 AX
1 x Bujia OS G5 gasolina
1 x OS 37 SZ-H, Connecting rod
2 x Brass control horn M2 long for wire (10pcs)
2 x Adjustable brass horn threaded M3
1 x Extra-long adjustable aluminium control horn 2,8x34
1 x Brass control horn M4 short for wire (10pcs)
1 x Propeller KAVAN 32x12 2-Bl
1 x 9x7 tree blades propeller
1 x Propeller POWER-PROP 13x8
1 x 11x7 tree blades propeller
1 x Propeller POWER-PROP 14x8
1 x Propeller MASTER 7x6
1 x Propeller MASTER 6x3
1 x Threaded coupler ALU M3 Ø 4 (2 uds)
1 x Sistema LDS - Ø12 mm servos Ø 6/25 spline 60º (Futaba) pitch
1 x Carbon Non-Woven, 245 g/m² 125 cm x 20 m
1 x Glass fabric 390 g/m² (silane, twill) 100 cm x 20m
1 x Fiberglass 163 g/m² 1m x 50 m (Aero, finish FK 144, plain)
1 x Carbon Fiber TeXtreme® 80 g/m² (plain) 100 cm, roll/ 10 m
1 x Glass fabric tape 225 g/m² (Silane, plain) 40 mm X 100m
1 x Vacuum bag, 1200 mm x 50 m
1 x Anodized aluminium servo M4x5/8 screw (4 red pcs)
1 x Anodized alum. M3x0,5x20 mm Flat Head screw (4 blue pcs)
1 x Aluminium wide washer M4 Gold (4 pcs)
1 x Nylon hinge 20x20x0,3 (10 pcs)
1 x 48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
1 x Small flex hinge (12 uds)
1 x Unmounted aluminium pin 6x98 mm (2 pcs)
1 x Propeller MASTER 7x3
1 x 8x6 tree blades propeller
1 x Propeller MASTER AIRSCREW 9x6
1 x Propeller G-Sonic 20x8
1 x Propeller POWER-PROP 14x10
1 x Propeller POWER-PROP 15x8
1 x Propeller MASTER 7x4
1 x 12x8 tree blades propeller
1 x Propeller MASTER 5,5x4,5
1 x Helice CLASSIC-Prop 20x10
1 x Propeller FOXY 34x12 2-Bl
1 x Helice FOXY 22x10 2-Bl
1 x Propeller MASTER AIRSCREW 9x6
1 x Propeller POWER-PROP 11x9
1 x Propeller MASTER 6x3,5
1 x Propeller POWER-PROP 16x8
1 x Propeller POWER-PROP 15x10
1 x 6x4 tree blades propeller
1 x Propeller MASTER 5,5x4
1 x 5 mm M2 variable inclined horn
1 x Duralumium F3A horn 30x10x23,5 mm (2 pcs)
7,499.15EUR
Manufacturers
Manufacturer Info
BSI
Other products
Languages
Español English
Currencies