Top » Catalog » Hardware » Power supply system/Data Recordi » PowerBoxSystems » POWER4450

439.01EUR

PowerBox Competition SR2
[POWER4450]

Features

22 channels
High-performance battery backer with high continuous load capacity
2.4” TFT screen, legible in sunlight
Bi-lingual menu system
Consistent duplication of all power electronics
Redundant electronic switch
Servo matching for all 22 outputs
Auto matching function
Two independent door sequencers with Setup Assistant
The latest integrated iGyro technology, using the iGyroSAT as gyro sensor
Twelve independent gyro outputs for: 4x aileron, 4x elevator, 4x rudder
Individual gain control for all twelve gyro outputs
Special regulatory algorithm for fixed-wing models
System detects all transmitter mixers
Four selectable output voltages: 6.0 V, 7.4 V, 7.8 V or unregulated
Graphic menu diagrams ensure ultra-simple programming
Fast basic setup procedure using the sophisticated Assistant
Optional GPS III for speed-dependent gyro compensation
Telemetry data for PowerBox P²BUS, Futaba S.BUS2, Jeti Ex-BUS, Spektrum SRXL2, Multiplex M-Link and Graupner HoTT
Transmission of battery, receiver and GPS* data
Virtually all features can be controlled from PowerBox and Jeti transmitters
Selectable servo frame rate: 10ms, 12ms, 14ms, 16ms, 18ms
Servo feedback current suppression
Latest 32-bit micro-processor for precise, high-speed signal processing
High-performance machined heat-sink for optimised heat diffusion
Machined, anodised aluminium switch and screen case
Compact dimensions

Technical Data
Operating voltage 4.0V - 9.0V
Power supply 2S LiPo, 2S LiIon, 2S LiFePo, 5S NiCd/NiMH
Current drain Power-on state 260mA
Current drain Standby 30µA
Maximum load current 2x40A (<30s)
Drop-out voltage 0.3V
Output voltage 6.0V, 7.4V, 7.8V, unregulated
Signal input serial
Supported RC systems PowerBox, Futaba, Jeti, Spektrum, M-Link and Hott
Receiver redundancy SRS
Channels 26
Servo sockets 22
Programmable servo outputs 22
Servo signal resolution 0,25µs
Signal frame rate 10ms, 12ms, 14ms, 16ms, 18ms
Gyro sensor type external iGyro SAT
Number of sensor axes 12
Screen TFT 320x240 pixels
Integral door sequencer yes
Supported telemetry systems P²BUS, S.BUS2, EX-Tele, SRXL2, M-Link, Hott

Dimensions 107 x 69 x 19 mm
Weight 115g
Weight Sensor Switch 15g
Weight of LCD screen 34g
Temperature range -30°C to +105°C

under request

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
    Bavarian Demon
    Dymond
    Eagle Tree
    Emcotec
    Futaba
    Jeti
    PowerBoxSystems
    ROI IMPORT
    SebART
    Setlo
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

21x14 BIELA propeller (3-blades) Pusher
89.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

1 x	Carbon fibre tape 200 g/m² (unidirectional) 50 mm
1 x	BALSA trip 8.0x8.0x1000 mm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x	Mahogany wood slat 3.0x3.0x1000 mm
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x	Hot Glue Stick BLACK
1 x	Vacuum Connection VA 1 (for hose Ø 6 mm)
1 x	Starter Sullivan-STAR 603 DINATRON
1 x	Vacuum pump 12 CFM
1 x	Hot Glue Stick RED
1 x	Ferrita 14x8x5.5 mm
1 x	100m servo "Premium" wire (white/red/blue)
1 x	Carbon fabric 160 g/m² (plain weave) 100 cm x 3 m
1 x	Straightened threaded rod M3 - 1m
1 x	Carbon Non-Woven, 160 g/m² 127 cm 5m
2 x	L cockpit anchor "tipe F3A" (2 pcs)
1 x	Silicone red 0,25 mm² wire (25 m)
1 x	Connectors banna oro 8,0 mm (M/F)
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	APM2.6 Power module with 5.3V DC BEC
1 x	White smoke bombs AX-60 (5 pcs)
1 x	3 mm Leader (L 100 mm)
1 x	Remote electric ignition system
1 x	LOWER TOW HOOK
1 x	ABS tube 6.0x5.0x1000 mm
1 x	Cable silicona female batt. receptor 30 cm (Futaba)
1 x	3 mm Prop Adapter M6
1 x	Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x	"L" servo arm 65x49 mm (2 pcs)
1 x	Carbon fiber rod 8.0 mmx1000 mm
1 x	BALSA triangular 6x6x1000 mm
1 x	Hardener Aero EPH 161 (250 g)
1 x	Pine wood slat 10x10x1000 mm
1 x	Liston HAYA 10 x 10 x 1000 mm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x	Trailing edge BALSA 35x8x1000 mm
1 x	CA Glue fast 20g
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (10 pcs)
1 x	Screwdriver for Hexagon 1,5mm
1 x	2,5x60 mm allen screwdriver
1 x	Starter 12v (Max 180 and 30ccm)
1 x	Screwdriver for Torx® TX8
2 x	Z Bender - S Type Tool
1 x	Copier 5x20 cm pcs
1 x	Copier 2x20 cm pcs
1 x	PROXXON - SILICON CARBIDE BELTS FOR BSL 220/E
1 x	3,0x60 mm allen screwdriver
1 x	Silicone 0,50 qmm servos wire Graupner(5 m)
1 x	Connectors banna oro 4 mm (M/F)
1 x	Couple M4 for wire (10 pcs)
1 x	Streamline Stainless Steel Tubing 12.3x7.7x1000 mm
1 x	Cierre cabina aluminio Ø4, I=10 mm
1 x	1/10 Pilot "Jimmy"
1 x	Brass hexagonal rod Ø 3.5 mm x 1000 mm
1 x	Steering arm 16 mm Ø 3 mm
1 x	ABS angle 6,0x6,0x1000 mm
1 x	Cockpit plastic closing
1 x	Streamline Stainless Steel Tubing 17.8x12.4x1000 mm
1 x	Spring lock washer 4.1 mm (20 pcs)
1 x	Quicklock washer 4 mm (10 pcs)
1 x	Green smoke canister 140 g
1 x	White smoke bombs AX-9 (10 pcs)
1 x	Yellow smoke canister 140 g
1 x	3 mm Prop Adapter M6
1 x	Carbon fiber rod 10 mm x 1000 mm
1 x	Propeller 10x4,7 SlowFlyer
1 x	PCARD Wireless System
1 x	Propeller 8x4,3 SlowFlyer
1 x	Extension silicon 50 cm (Futaba)
1 x	Carbon tube (L 1000 mm, Ø18 mm, Ø16 mm)
1 x	Ventral support for AX-18/AX-60
1 x	3,2 mm Prop Adapter M8
1 x	Extension silicon 10 cm (Futaba)
1 x	Smoke set "Glider"
1 x	Protective Cover for wires Ø 20 mm 1000 mm
1 x	BALSA leading edge 8x10x1000 mm
1 x	Propeller POWER-PROP 13x9
1 x	Linden wood slat 3.0x3.0x1000 mm
1 x	Carbon roving DowAksa / 24k / 1600 tex
1 x	Hardener Aero EPH 161 (500 g)
1 x	Pine wood slat 3.0x7.0x1000 mm
1 x	BALSA trip 3.0x5.0x1000 mm
1 x	Beech dowels 3.0 x 1000 mm
1 x	Wing-connector: Glass / Carbon tube (26.5/25 x 25/23) x 1000 mm
1 x	BALSA triangular 15x15x1000 mm
1 x	BALSA trip 5.0x5.0x1000 mm
2 x
1 x	Walnut wood slat 1.5x1.5x1000 mm
1 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x	Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 100M
1 x	Beech dowels 2.0 x 1000 mm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
1 x	BALSA triangular 10x10x1000 mm
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 10 m
1 x	Pine wood slat 2.0x2.0x1000 mm
1 x	TeXtreme® Carbon tape 38 g/m² (IM, unidirectional) 20 mm x 100m
1 x	Crimping tool
1 x	Starter Sullivan-STAR 601
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 80 GRIT (5 pcs)
1 x	Digital precision scale up to 2000 g
1 x	Starter EM Gear Power 80
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 180 GRIT (5 pcs)
1 x	Starter 12v (Max 90 and 15ccm)
1 x	Crimping tool
1 x	2,0x50 mm allen screwdriver
1 x	Starter EM Gear Power 250
1 x	Digital scale up to 40 kg
1 x	Cut tube
1 x	Disposable Injector Bags (30x16cm) 100 pcs
1 x	Extractor piñones 2.3/3.2 mm
1 x	Hot Glue Stick GREEN
1 x	Screwdriver for Hexagon 1,27mm
1 x	Z Bender - S Type Tool
1 x
1 x	Ball Link Plier
1 x	Ball Link Plier
1 x	Screwdriver for Torx® TX6
1 x	Dust collector for mould cleaning
1 x	1,5x50 mm allen screwdriver
1 x	Straightened rod Ø 5.5 mm x 1000 mm
1 x	USB Mini Camera endoscope
1 x	Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x	Xplorer4 anemometro
1 x	Aluminium red ball links M3 V1 (10 pcs)
1 x	2 LiPo XH>EH adapter
1 x	DUPLEX USBa USB-Adapter for Jeti Duplex Items
1 x	Ball link V1 Ø7 M4/3 (6 uds)
1 x	White silicone 0,25 qmm wire (150 m)
1 x	Demoulding wedge red (40 x 20 mm) 5 pcs
1 x	Profile ABS Square 2 x 1000 mm
1 x	Aluminium cap bolt washer M3 black (8 pcs)
1 x	PVC 0,35 qmm servos wire Graupner (100 m)
1 x	Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x	Spring lock washer 3.1 mm (20 pcs)
1 x	Banna gold connector 2,5 mm (M/F)
1 x	Straightened rod Ø 5.0 mm x 1000 mm
1 x	AC-10 pre-rotacion with motor
1 x	Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x	Straightened rod Ø 1.0 mm x 1000 mm
1 x	Soporte grifo FESTO vertical (1 pcs)
1 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Soporte filtro FESTO (4 pcs)
1 x	Vacuum sealing tape, 2.5 x 12 mm (up to 140 °C) 15 m
1 x	White silicone 0,25 qmm wire (100 m)
1 x	Gold antispark 4 mm plug
1 x	Cabin latch Fox MDM1 4m (pair)
1 x	Antenna Cloverleaf 5.8 GHz Tx - Rx
1 x	ARAMID honeycomb 1300x2600x2 mm
1 x	Stainless steel cable Ø 0.62 mm (10 m)
1 x	Screw-lock connector Ø 2 mm (2 uds)
1 x	Support FUEL DOT V3
1 x	L-Connector 4.0 mm x 1000 mm
1 x	ABS angle 4,0x4,0x1000 mm
1 x	10m servo "Premium" wire (white/red/blue)
1 x	Sun Cover PC 21 XXL (JMB Jets)
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 3m
1 x	Tube support Ø 6mm (10 pcs)
1 x	Straightened rod Ø 6.0 mm x 1000 mm
1 x	Support ECU Xicoy X-45
1 x	Aluminium cap bolt washer M3 green (8 pcs)
1 x	Xplorer3 anemometro
1 x	Oils Pumps Empty (1 liter)
1 x	Glass fabric tape 225 g/m² (Silane, plain) 30 mm X 100m
1 x	Civilian pilot "G-Man" size 9cm (Slimline)
1 x	Ball link Aluminio M3 x 3 x 5 x 18mm (6 uds)
1 x	Straightened rod Ø 14.0 mm x 1000 mm
1 x	Pilot "Anthony" (Slimline)
1 x	U Profile ABS 2,0x4,0x1000 mm
1 x	L-Connector 1.5 mm x 1000 mm
1 x	ABS angle 2,0x2,0x1000 mm
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	PVC 0,25 qmm servos wire Graupner (5 m)
1 x	Wing connector 8pin with pin strip, plug & socket
1 x	Z type of cable coupler Ø 1 (2 uds)
1 x	XH male balance (2S) connector (2 pcs)
1 x	Locking cable tie 4.6x203 (uds)
1 x	Xplorer2 anemometro
1 x	Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
1 x	Support XT60 conector (2 pcs)

6,368.44EUR