40.00EUR

NF-3m Heli Kit
[NF-3m Heli Kit]


The NF-3m Heli Kit is unit with cables and LEDs ready to install into an indoor helicopter. Length of cables correspond to models like EasyCopter, Blade or Lama. There are 6 lights (LEDs 3mm) installed : two position lights (Red and Green), two flashing lights (Red and White) and two landing lights (White).

NF-3m Heli Kit has cable into a receiver. This is ready to work with helicopters having a free channel to control the lights by a pilot. Operational voltage is expected by BEC, typical voltage is 5,0 V. Works from 4,5 V to 5,5 V.

The circuit is to be connected with a Graupner or Hitec connector directly to the receiver, being supplied with a voltage of 5V and with BEC circuit tolerance. The circuit has no other protection against reversed polarity than a connector lock. Diodes are supplied with this voltage. The output conntacts have a joint positive pole. Each output can be connected with one diode.
The F1 and F2 circuits (see manual) flash with one second period. Using three jumpers ( 1, 2, 4 ), one of the eight preset flashing combinations can be achieved i.e. one, two or three separated flashings. You can set the order number of the combination from 0 to 7 by means of the jumpers as follows: all jumpers, when disconnected, sum up to 0. The sum of number of the connected jumpers represents the number of the selected combination.

The unit NF-3m can also be connected as an uncontrolled unit when disconnecting the orange signal contact on the connector on the receiver. This can be either cut off or you can gently try to lift the lock on the connector and pull the contact out of the connector. Then isolate against touching by chance. If necessary, you can always push the contact back again. When connecting the unit as an uncontrolled one (without the orange contact) the position and the flashing lights are permanently switched on and the jumper "2p/3p" switches the landing lights.

The total average current consumption by all lights on is between 12 mA from a BEC. During 10 minutes of fly the light circuits burn only a little bit more than 1 % of capacity of a 700 mAh accumulator. Position and number of the installed LEDs depends on your own decision. However, you should keep in mind that, according to conventions, position lights are correspond with the green diode on the right and the red one on the left, in the flying direction. Usually the flashing light on the body is red and on the tail is white.

The NF-3m, besides control circuit, includes 1x3 mm 10 mAh green LED, 2x3 mm 10 mAh red LEDs and 3x3 mm 10 mAh white LEDs


temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
Servo slow down unit (0,7-14,7 sec )
Servo slow down unit (0,7-14,7 sec )

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x Threaded coupler ALU M3 Ø 4 (2 uds)
2 x Brass control horn M4 short for wire (4 pcs)
2 x Threaded coupler ALU Left M3 Ø 4 (2 uds)
1 x Threaded coupler ALU M2,5 Ø 6 (2 uds)
2 x Horn 5/20 with M2 Bearing
1 x Threaded coupler ALU M2 Ø 4 (2 uds)
1 x Horn 5/10 with M2 Bearing
2 x Horn with ball 55x40
2 x Horn 20x28,5 mm (2 pcs)
3 x Threaded coupler ALU M3 Ø 5 (2 uds)
2 x SlowFlyer control horn (3 pcs)
1 x Cable control set
2 x RH long aluminium horn (2pcs)
1 x Threaded coupler ALU M2 Ø 3 (2 uds)
2 x 20 mm carbon horn
2 x Threaded coupler ALU M2,5 Ø 4 (2 uds)
2 x 6 mm blue aluminium threaded horn with patella
2 x Small aluminium horn gold (2pcs)
2 x Brass control horn M4 short for wire (10pcs)
2 x LH long aluminium horn L31xH30 (2pcs)
2 x LH long black aluminium horn L31xH30 (2pcs)
1 x Small aluminium horn blue (2pcs)
1 x Horn 13,5x16 mm (2 pcs)
1 x 6 mm red aluminium threaded horn with patella
1 x Softshell Hispano Aviación
2 x Horn for flap control (1 pcs)
2 x Horn 6/20 with M3 Bearing
1 x Vest clothes Hispano Aviación
2 x Threaded coupler ALU Left M2,5 Ø 4 (2 uds)
2 x Small aluminium horn red (2pcs)
2 x Jeti Black cap
1 x Carbon fiber rod 4.0 mmx1000 mm
1 x Carbon fiber rod 0.8 mmx1000 mm
1 x Carbon fiber flat 1000x3.0x0.5 mm
1 x Carbon fiber rod 20 mmx1000 mm
1 x Carbon fiber rod 2.5 mmx1000 mm
1 x Carbon fiber rod 1.5 mm x 1000 mm
1 x Carbon fiber rod 14 mmx1000 mm
1 x Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm
1 x Carbon fiber rod 7.0 mmx1000 mm
1 x Carbon fiber rod 0.5 mmx1000 mm
1 x Tape GFK 38 mm
1 x SE Ring 360 mm (2 pcs)
1 x 20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
2 x Stickers-digit for marking
1 x Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x SE Ring 450 mm (2 pcs)
1 x 14x60 mm Mini rings Tie Wraps (4 pcs)
1 x 13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x 5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x Battery EMCOTEC LiIon 3000 7.2v
1 x LiIon Battery 3000 mAh 3.3v 15A (2 pcs)
1 x Battery RX JETI LiIon RB 3100 7.2v
1 x Battery RX JETI LiIon RB 2600 7.2v
2 x Battery RX JETI LiIon RB 5200 7.2v
1 x M2,5 Diam metal short ball link V3 (2 pcs)
1 x Brass hexagonal rod Ø 4 mm x 1000 mm
1 x Pin type hinge Al 6x98 mm (2 pcs)
1 x Quicklock washer 1.5 mm (10 pcs)
1 x Disposable Injector Bags (30x16cm) 100 pcs
1 x Extension silicon 30 cm female (Futaba)
1 x Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x Crimping sleeves for 1.1 mm cable (10 pcs)
1 x Aluminium coupler M2,5/2 with ball bearing (1 pcs)
1 x Shirt Hispano Aviación
1 x Soporte grifo FESTO (2 pcs)
1 x Support pumb/filter Xicoy X45
1 x Small adjustable control horn with bearing
2 x Horn DU-BRO 1/2 (2 pcs)
1 x Short extra-strong control horn with bearing 2,8x15
1 x Sistema LDS - Ø12 mm servos Ø 5/24 spline 95º (MKS) pitch 7 mm
2 x Threaded coupler ALU Left M2,5 Ø 3 (2 uds)
2 x Threaded coupler ALU M3 Ø 6 (2 uds)
1 x Horn mando long (2 pcs)
2 x Cable with accesories
3 x Horn 16,5x20 mm (2 pcs)
1 x Horn with ball 40x30
1 x Carbon plate 350x150x3.0 mm
1 x SyRen 50A 6V-30V Regenerative Motor Driver
1 x Duplex 2.4 EX TopFuel MTAG Battery Reader
2 x Horn 6/35 with M3 Bearing
2 x 6 mm aluminium horn with patella
1 x Lock washer 4.3 mm (20 pcs)
1 x Lock nut M2 (20 pcs)
1 x Lock nut M2.5 (10 pcs)
1 x Hexagonal Nut M4 (10 pcs)
1 x Circlik for shaft 1.9 mm (10 pcs)
1 x Hexagonal Nut M1,6 (10 pcs)
1 x Hexagonal Nut M4 (20 pcs)
1 x Circlik for shaft 2.3 mm (10 pcs)
1 x Lock nut aluminium M2 (4 pcs)
1 x Wing bolts M6 Steel screw Blue (2 pcs)
1 x Steering arm 16 mm Ø 4 mm (2 uds)
1 x Steering arm 16 mm Ø 3 mm (2 uds)
1 x Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x Tip wing protector 40x14 (2 pcs)
1 x Steering arm 12 mm Ø 4 mm
1 x 22m Fitting barb
1 x 1/12 Pilot "Fighter"
1 x 102 mm aluminium spinner
1 x 1/4 Pilot "Mike"
1 x "Taxi Tank" Fuel Tank
1 x 1/6 Pilot "John"
1 x 25 mm carbon servo arm
2 x PowerPack 2.5X2 PRO
1 x DUPLEX 2,4GHz MRPM EX
1 x DSM 10 Dual Switch Mixer
1 x Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x Horn 6/27 with M3 Bearing
1 x Horn 5/15 with M2 Bearing
1 x Brass control horn M2 short for wire (2 pcs)
1 x Sun Cover BULL Mo1 2.6 (Hispano Aviacion)
1 x Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
1 x Sun Cover PC 21 XXL (JMB Jets)
1 x TeXtreme® Carbon tape 38 g/m² (IM, unidirectional) 20 mm x 100m
1 x 25 mm fenders (10 pcs)
1 x Carbon fibre tape 200 g/m² (unidirectional) 50 mm
1 x Carbon tube (L 1000 mm, Ø8 mm, Ø6 mm)
1 x 24x12 prop Super Silence
1 x 8 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x Cooler motor type 400
1 x SLICK 360-A 104" (2640 mm)
1 x Battery RX JETI LiIon RB 6200 7.2v
1 x 3 mm Leader (L 100 mm)
1 x 3,2 mm Prop Adapter M8
1 x 290 mm M4/4 mm Prop shaft
1 x CA Glue (medium) 20g
1 x Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x Digital scale up to 40 kg
1 x 31,0 mm propeller (rigth propeller)
1 x 2.3 mm Adapter for 30 mm spinners
1 x Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm
1 x Hard brass tubing (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x Tygon tube 4.8 x 3.2 mm 15 m
1 x Carbon fiber rod 10 mm x 1000 mm
1 x TYGON tubo 1 m Diam. 3.4 x 2.0 mm
1 x Straightened threaded rod M3 - 1m
1 x PHASOR RACE 2035/2100 2D
1 x 3,9 mm ZG20-ZG38 servo arm
1 x 3-blades 29x12 carbon prop Super Silence
1 x 60 mm long Prop hub for ZG45SL, ZG62/S/SL and ZG80B
1 x 3-blades 30x12 carbon prop Super Silence
1 x 1000 ccm gasoline fuel tank
1 x 26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x 
1 x VTX 477 Carbon Rotorblade
1 x LOGO 600 SX (kit)
1 x Motor holder AXI
1 x Ø 28 mm fiberglass motor-holder for electric motors
1 x RCEXL Electronic ignition twin A-02
1 x Ignition bed V2 Red color
1 x Motor Mount for Multiplex FunJet
1 x PITTS CHALLENGER 87″ 2.20m (120cc) 02 ARF
1 x Sukhoi 29S 2,6 m White/Blue (SebART)
1 x Tray JETI for DS-14/16/24 Black
2 x Transmitter Stick Ends JETI DS-16/14
2 x Transmitter JETI Duplex DS-12 EX Multimod RED
10,675.25EUR
Manufacturers
Manufacturer Info
Night Fly
Night Fly Homepage
Other products
Languages
Español English
Currencies