13.90EUR

Epoxy SLOW-CURE™ 30 min (130g)
[BSI205]


If CAs are the cure-all for just about all bonding problems, you may be wondering, "Why do I need epoxy?" One primary reason is price. Epoxy costs are about one fourth that of CA. When large objects are being bonded, economics can be a deciding factor on choice of adhesive. The specific characteristics of epoxies also give them advantages in some applications. All our epoxies are mixed with a 50-50 ratio. Any scrap material or paper scratch pad can be used as a mixing surface. We have found, however, that the plastic tops to coffee cans work best due to their outer border and their flexibility, which allows the unused cured epoxy to be released and thrown away.
Squeeze out equal length beads of the desired amount of epoxy, then mix together thoroughly with a popsicle stick or scrap piece of material. In cold weather, epoxy takes longer to cure (too cold and usually they never fully cure) and becomes more difficult to get out of the bottle, especially if it’s less than 1/2 full. The epoxies can be heated in a microwave oven for about 10 seconds so that they flow easier. The heating process, with the caps off, also releases any moisture that can be absorbed by epoxies. Their shelf life, therefore, is virtually unlimited.
Acetone works as the best solvent for cleaning epoxy from brushes and unwanted surfaces before it cures. If epoxy gets on surfaces that acetone will attack, use isopropyl alcohol. We do not recommend any additives for thinning epoxies due to their effect on curing and overall strength. If thin epoxy is required, either use heat or switch to EX-SLOW™ or FINISH-CURE™. Epoxies bond best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion.
A small amount of CA can be used in strategic locations to hold parts in place while the epoxies cure. The minute designations for epoxies refer to the working time, i.e., the time one has before the epoxies begin to set up after being mixed in a large mass. When spread into thinner layers, the working time in increased significantly (except QUIK-CURE™). Working time decreases approximately 25% at temperatures above 90 degrees F. Don’t panic if your skin comes in contact with either epoxy or CA.
While contact should be avoided, uncured epoxy can be washed from your skin with soap and water. Allergic reactions are rare. Cured epoxy and CA can be peeled off the skin and usually are gone after a full day of normal activity. UN-CURE™ will debond any body parts that get stuck together if a peeling action (never pulling) doesn’t part them.

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.


many units
many units

Reviews

Customers who bought this product also purchased
UHU Por 50ml/40g
UHU Por 50ml/40g

many units
many units

Round flex hinge (12 uds)
Round flex hinge (12 uds)

many units
many units

Fast'n EZ-CA-Hinge (12 uds)
Fast'n EZ-CA-Hinge (12 uds)

many units
many units

Balsa panel 4.0x100x1000 mm
Balsa panel 4.0x100x1000 mm

many units
many units

BALSA trip 3.0x3.0x1000 mm
BALSA trip 3.0x3.0x1000 mm

many units
many units

Fast'n EZ-CA-Hinge, lite (12 uds)
Fast'n EZ-CA-Hinge, lite (12 uds)

many units
many units

Categories
* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->
  
  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
    Cianocrylate->
    Epoxy->
      EMC-Vega
      KAVAN
      Loctite
      Resoltech
      Epoxy BSI
      Epoxy R-G
    Resin/Gelcoat
    Glass Bubbles
    Contact adhesive
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x M2,5 5Diam metal ball link V3 (2 pcs)
2 x M2/M1/6 3Diam long black ball link V1 (6 pcs)
2 x M3 Maxi ball link (2 uds)
2 x Strip ABS 2.0x10.0x1000 mm
1 x M2,5 Diam metal ball link V3 (2 pcs)
1 x ABS Strip 1.5x6.0x1000 mm
1 x Joint with bearing M2 22x5,5
1 x Short ball link M2 (6 uds)
1 x M3 Maxi ball link (2 uds)
1 x M2/M1/6 3Diam short black ball link V1 (2 pcs)
1 x Long ball link M2 (6 uds)
1 x Long ball link M1.6 (6 uds)
2 x Joint with bearing M3 22x5,5
2 x Strip ABS 2.0x5.0x1000 mm
2 x Round Rod 2,5x1000 mm
2 x ABS Strip 1.0x4.0x1000 mm
1 x M3 Maxi ball link (2 uds)
1 x ABS Strip 1.5x4.0x1000 mm
2 x Round Rod 5,0x1000 mm
1 x ABS Strip 1.0x3.0x1000 mm
1 x ABS I Strip 10x5x1000 mm
2 x ABS Strip 1.0x5.0x1000 mm
1 x Ball link M3 RPA's-UAV's
1 x Blue metalic ball link M3/3 azul (2 pcs)
1 x M3 INDUSTRIAL ball link (2 uds)
3 x ABS Strip 1.5x8.0x1000 mm
1 x Long ball link M3 (6 uds)
2 x Round Rod 4,0x1000 mm
1 x ABS I Strip 20x10x1000 mm
1 x Short ball link M1.6 (6 uds)
1 x Socket head long ball link M3 (2 uds)
1 x M2 5Diam short black ball link V2 (2 pcs)
1 x M2,5 Diam metal short ball link V3 (2 pcs)
2 x M2/M1/6 3Diam short black ball link V1 (6 pcs)
1 x Ball link M3 (10 pcs)
2 x Round Rod 1,25x1000 mm
2 x Joint with bearing M2,5 22x5,5
1 x ABS Strip 1.5x2.0x1000 mm
1 x Ball link M1.6 (6 uds)
2 x Round Rod 6,0x1000 mm
2 x Socket head ball link M3 (2 uds)
1 x Strip 3,5x1,75x330 mm
1 x M2,5 / 5Diam metal short ball link V3 (2 pcs)
1 x Ball link M2 (10 pcs)
2 x Round Rod 1,0x1000 mm
1 x M2 5Diam black ball link V2 (2 pcs)
1 x Socket head ball link M3 (2 uds)
2 x Stickers-digit for marking
1 x Cable silicona macho batt. receptor 30 cm (Futaba)
2 x Extension silicon 10 cm (Futaba)
2 x Extension 7.5 cm
2 x Prolongador S-Bus JR/JR 20cm
2 x Futaba Female 40 cm extension
2 x Extension silicon 30 cm male (Futaba)
1 x Extension silicon 100 cm (Graupner)
1 x Nylon hinge 20x20x0,3 (10 pcs)
1 x 48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x Long pinned hinge (6 uds)
2 x 43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x 67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
2 x Unmounted aluminium pin 6x98 mm (2 pcs)
1 x 76 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x Micro flex hinge (12 uds)
2 x 25 mm reinforced hinge
1 x 67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x LOWER TOW HOOK
1 x Carbon fiber rod 2.5 mmx1000 mm
1 x Initior Transmitter FTX2 Wireless
1 x 1/12 Pilot "Langley"
1 x Red smoke bombs AX-60 (5 pcs)
2 x Actuador lineal HLS12-100210-7.4v
3 x Strip 2,0x2,0x330 mm
1 x Ball link M3 (10 pcs, flat ball)
2 x Round Rod 2,0x1000 mm
1 x Soporte filtro FESTO (4 pcs)
2 x Socket head long ball link M3 (6 uds)
1 x Pasacables rectangular 40x15 mm (4 pcs)
1 x Aro pasacable Ø25 mm (4 pcs)
1 x Support conector MPX (6 pcs)
1 x Futaba Female 40 cm extension
1 x Extension silicon 25 cm (Futaba)
1 x Extension silicon 25 cm (Graupner)
1 x Pin type hinge Al 3,0x50 mm (2 pcs)
1 x Gates hinge
1 x Extension silicon 50 cm (Futaba)
1 x Pin type hinge Al 4,5x70 mm (2 pcs)
2 x Premium servo extension 25cm
1 x Extension 30 cm (Futaba)
1 x Premium servo extension 100cm
2 x Extension silicon 75 cm (Graupner)
1 x Extension silicon 30 cm male (Graupner)
1 x Extension 15 cm (Futaba)
1 x Flap hinge (6 pcs)
1 x 6 mm ball link M3 (10 pcs)
1 x Extension silicon 75 cm (Futaba)
1 x 33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x Miniature brass strap hinge, 1 m
1 x Long pinned hinge (12 uds)
1 x Extension silicon 35 cm (Futaba)
1 x Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
1 x servo adapter lead, JST-SH socket - JR male Pin, for GR-12SH+HoT
1 x Extension silicon 100 cm (Futaba)
1 x Premium servo extension 50cm
1 x Extension silicon 10 cm (Graupner)
1 x Indoor hinge with servo arm integraded
1 x Gates hinge black 30x16 mm (2 pcs)
1 x 6 mm hexagonal ball link M3 (10 pcs)
1 x Cable silicona macho batt. receptor 30 cm (Graupner)
1 x Pine wood slat 2.0x2.0x1000 mm
1 x Linden wood slat 2.0x2.0x1000 mm
1 x Nylon hinge 20x15x0,3 (10 pcs)
1 x Tip wing protector 28x10x12 (2 pcs)
1 x Small pinned hinge (12 uds)
1 x BALSA trip 2.0x2.0x1000 mm
1 x 41x5,5 mm wires output (2 pcs)
1 x Dremel 3000 130W
1 x Carbon tube (L 1000 mm, Ø10 mm, Ø8 mm)
1 x ABS tube 6.0x5.0x1000 mm
1 x BALSA trip 10x10x1000 mm
1 x Pine wood slat 3.0x5.0x1000 mm
1 x Pine wood slat 5.0x5.0x1000 mm
1 x Trailing edge BALSA 35x8x1000 mm
1 x Pine wood slat 6.0x6.0x1000 mm
1 x ROBART POINT HINGE 4,7mm (5 pcs)
1 x Small flex hinge (12 uds)
1 x LOGO 600 SX (kit)
1 x TA1200 Charger Compatible with Smart and Standard LiPo Batteries
1 x Cargqador GensAce IMARS III Pro Smart Balance RC
1 x Charger Li Polymer Multi-Cell Multi-Rate Charger (MCMR)
1 x CellPRO 4S Adaptader (GP/KO up to 4S)
1 x BALSA trip 8.0x8.0x1000 mm
1 x Strip 2,5x1,25x330 mm
2,633.17EUR
Manufacturers
Manufacturer Info
BSI
Other products
Languages
Español English
Currencies