Top » Catalog » Motors & Turbines » Electric » Brushless » KAVAN » KAV30.1638C

120.00EUR

Combo KAVAN PRO 3542-1150 + KAVAN PRO-80 SB
[KAV30.1638C]

Combo set of BLS motor with 80A ESC for model aircraft: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 rpm per V, power supply Lixx 3-4s, shaft 5 mm.

Outrunner brushless electric motor for model aeroplanes: glider 2200g, trainer 2100g, acro 1800g, 3D 1200g, KV1150 RPM/V, input voltage 3-4S Lixx. 5.0mm shaft. Alternative designation based on the stator dimension: 2820-1150. KAVAN PRO series motors are high performance 14-pole brushless outrunners. State-of-the-art design, hardened steel shafts, high quality ball bearings, High grade material used for stators and rotors ensure long lifetime and unbeatable performance and high efficiency. KAVAN PRO series motors are low revolution/high torque electric motors capable of swinging large diameter propellers without need for a gearbox.
KAVAN PRO 3542-1150 is a motor for model aeroplanes up to 2200 g all-up weight powered by 3-4S LiPo flight battery pack. It is great for faster 2000-2500 mm electric powered gliders, 1400-1500 mm high wing trainers, scale and aerobatic models.
Motor installation: KAVAN 3542-1150 has been designed both for the front and radial mount installation. Front mount: Use four M3 screws; these may not go deeper than 3-4 mm into the front case. Radial mount: Use four M3 screws to secure the mounting cross to the firewall. The firewall should be made of 4.0-5.0 mm plywood. The radial mount set is supplied with the motor.
The motor set contents: KAVAN PRO 3542-1150 motor w. cables (3.5 mm gold-plated connectors), radial mount set accessories. The full instruction manual can be downloaded here: KAVAN PRO Brushless Motors Instruction Manual
Note: Alternative designation based on the stator dimensions: 2820-1150.
Powering LiXX cells 3 - 4
RPM/V [ot./min/V] 1150
Max. power (180 s) [W] 1000
Internal resistance [mOhm] 16
Open-circuit current (při 10 V) [A] 2.7
Max. peak current (180 s) [A] 70
Diameter [mm] 35.2
Length [mm] 41
Length celková [mm] 63.5
Shaft diameter [mm] 5
Weight [g] 141
Poles count 14
Timing [°] 20 - 25
ESC [A] 70 - 80
Weight of glider (up-to) [g] 2200
Weight of trainer (up-to) [g] 2100
Weight of acrobat (up-to) [g] 1800
Weight of 3D (up-to) [g] 1200
Doporučená vrtule 3S: 11x8"-12x6"
4S: 9x6"-10x5.5”

under request

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->
Car/Trucks->
Motors & Turbines->
  Explosion->
  Turbines->
  Electric->
    Brusehd->
    Brushless->
      Actro
      AXI->
      FOXY/RAY
      Glavak
      Hacker
      Hacker FES System
      JETI
      KAVAN
      Kontronik->
      Mega
      MP Jet
      MULTIPLEX
      MVVS
      O.S.
      Plettemberg
      RIPMAX
      ROI-Import
      Scorpion Motor
      T-Motor
      Top Model CZ
      Typhoon
    Accesorios
  Rockets
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

VSpeak ECU converter KingTech
79.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

3 x	Regulador Jeti Jes 045
1 x	Carbon roving DowAksa / 24k / 1600 tex
1 x	Electric spoiler 250 mm (2 pcs)
1 x	Carbon Non-Woven, 160 g/m² 127 cm 1 m
2 x	Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x	Fibra carbono tela 160g/m2 100 cm x 2 m (twill weave)
2 x	Micro screw-lock pushrod conn snap Ø 1 mm (2 uds)
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
2 x	Stainless steel cable Ø 0.5 mm (10 m)
1 x	L cockpit anchor "tipe F3A" (2 pcs)
2 x	Horizontal cockpit anchor "tipe F3A" (2 pcs)
1 x	Stainless steel cable Ø 0.5 mm (2 m)
1 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Vacuum bag, 1200 mm x 50 m
2 x	Carbon fabric 160 g/m² (plain weave) 100 cm x 3 m
1 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x	Steering arm 12 mm Ø 4 mm (2 uds)
2 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x	Screw-lock pushrod conn snap Ø 1.5 mm (2 uds)
2 x	Stainless steel cable Ø 0.5 mm (20 m)
1 x	Stainless steel cable Ø 1.3 mm (10 m)
1 x	Cierre cabina aluminio Ø5, I=16 mm
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 20 m
1 x	Crimping sleeves for cable 1.3 mm (10 pcs)
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 50 m
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
1 x	Locking cable tie 2.5x100 (uds)
1 x	Cap closure 33/23.5mm (2 uds)
2 x	Cabin latch Fox MDM1 4m (pair)
1 x	Vacuum sealing tape, 2.5 x 12 mm (up to 140 °C) 22 roll
1 x	ARAMID honeycomb 1300x2600x2 mm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x	Canopy Latch
2 x	Locking cable tie 4.6x203 (uds)
2 x	Screw-lock connector M2 (2 uds)
3 x	Screw-lock connector Ø 2 mm (2 uds)
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	Carbon fabric 160 g/m² (twill weave) 127 cm, roll/ 10 m
1 x	Aluminium alloy coupler for carbon tube 6/M4
1 x	Steering arm 16 mm Ø 3 mm (2 uds)
2 x	Carbon Non-Woven, 160 g/m² 127 cm 5m
1 x	Vacuum sealing tape, 2.5 x 12 mm (up to 140 °C) 15 m
1 x	Crimping sleeves for cable 0.85 mm (10 pcs)
3 x	Stainless steel cable Ø 0.62 mm (10 m)
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (10 pcs)
1 x	Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 50M
1 x	Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x	Locking cable tie 3.2x142 (uds)
2 x	30 cm BEC cable (male)
1 x	4 LiPo XH>EH adapter
1 x	Adapter lead MPX/EC3
2 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	Copper lacquer wire Ø0,2 mm (5 m)
2 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
2 x	Cabel charger transmitter GRAUPNER
2 x	CellPRO 4S Adaptader (GP/KO up to 4S)
2 x	CC 02
3 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	2 LiPo XH>EH adapter
1 x	3 LiPo XH>EH adapter
1 x	DPSI magnetic switch actuator (housing)
2 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
2 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	APM2.6 Power module with 5.3V DC BEC
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
2 x	30 cm BEC cable (female)
2 x	Black copper lacquer wire Ø0,2 mm (5 m)
1 x	Adapter lead MPX/XT60
3 x	5 LiPo XH>EH adapter
1 x	Motor A2212/13T
1 x	Balsa panel 8.0x100x1000 mm
1 x	White smoke bombs AX-18 (5 pcs)
1 x	Yellow smoke bombs AX-60 (5 pcs)
1 x	Aluminium coupler M2/2 with ball bearing (1 pcs)
1 x	Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 3m
1 x	Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x	Glass fabric 80 g/m² (FK 144, twill weave) 100 cm, pack/ 5 m
1 x	Sheet Depron Aero 1250x800x3 mm
1 x	Teflon rollers 80 mm x 15 mm Diam.
1 x	Styrene plate 320x120x0.5 mm
2 x	Cockpit plastic closing
1 x	Steering arm 16 mm Ø 3 mm
1 x	Fiberglass plate 350x150x2.0 mm
1 x	Aro pasacable Ø20 mm (4 pcs)
1 x	Steering arm 12 mm Ø 3 mm (2 uds)
1 x	Foam plastic plates (310x210x8 mm)
2 x	Aluminun wheel collar 3 mm Ø (4 uds)
1 x	Snap short M2 (10 uds)
1 x	Cable grommet Ø 6.4 mm (4 uds)
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 55
1 x	Allen wheel collar M4x4
1 x	Actuador lineal HLS12-100210-7.4v
1 x	Snap for floding prop for 2 mm axi
1 x	100 mm rods + T patellas set for direction control
1 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x	Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 100M
1 x	Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x	Glass fabric tape 225 g/m² (Silane, plain) 40 mm X 100m
1 x	Cierre cabina aluminio Ø4, I=10 mm
1 x	Demoulding wedge red (40 x 20 mm) 5 pcs
2 x	Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x	PWC4 wing/fuselage connector for 4 servos
1 x	CC 05
1 x	SPARK Switch 7.4v
1 x	SPS Remote switch actuator
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	DUPLEX USBa USB-Adapter for Jeti Duplex Items
2 x	Ring support P-20 OPUS V-Jet 60mm
1 x	Extension silicon 30 cm male (Graupner)
1 x	Extension silicon 100 cm (Graupner)
1 x	Extension silicon 10 cm (Futaba)
1 x	Extension silicon 30 cm female (Graupner)
1 x	Premium servo extension 100cm
1 x	Threaded coupler ALU M3 Ø 6 (2 uds)
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	Threaded coupler ALU M2,5 Ø 6 (2 uds)
1 x	Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x	Pulley brass 14/2 (2 pcs)
1 x	Crimping sleeves for 1.1 mm cable (10 pcs)
1 x	M3 Maxi ball link (2 uds)
2 x	Selfstart electronic switch
1 x	SPS 70V 100/200 A
1 x	SBEC 30 D
1 x	Pins M connect Multipin connectors AWG 20-24
1 x	USB Interface REVOLECTRIX for CellPRO 10s
1 x	MAX BEC 2
1 x	3 copper lacquer wire Ø0,2 mm (1 m)
1 x	Servo slow down unit (0,7-14,7 sec )
1 x	Opto Gas Engine Kill Switch
1 x	Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
1 x	Cockpit aluminium closing 4.7g
2 x	Fully Threaded Steel Rod Duralumin 60 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod Duralumin 120 mm M3 (2 pcs)
1 x	45 mm rods set for direction control
2 x	Pushrod octagone 4/3
1 x	Press fitting for 1,0 diam. steel cable (10 pcs)
1 x	Fiberglass plate 350x150x1.5 mm
1 x	Cable silicona female batt. receptor 30 cm (Futaba)
1 x	Extension silicon 25 cm (Graupner)
1 x	Press fitting for 0,5 diam. steel cable (10 pcs)
1 x	Fully Threaded Steel Rod alumin 70 mm M3 (2 pcs)
1 x	80 mm rods set for direction control
2 x	Fully Threaded Steel Rod M3
1 x	Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod Duralumin 80 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 60 mm M3 (2 pcs) knurled
1 x	Fully Threaded Steel Rod alumin 60 mm M2,5 (2 pcs)
1 x	Fully Threaded Steel Rod SUS303 70mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs) knurled
1 x	Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 70 mm M3 (2 pcs) knurled
3 x	Fully Threaded Steel Rod Duralumin 90 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod Duralumin 110 mm M3 (2 pcs)
2 x	Pushrod greyline 4/3 with coupler M3
1 x	Fully Threaded Steel Rod Duralumin 70 mm M3 (2 pcs)
2 x	Fully Threaded Steel Rod SUS303 65 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 90 mm M2,5 (2 pcs)
1 x	100 mm rods set for direction control
1 x	Fully Threaded Steel Rod Duralumin 130 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod Duralumin 50 mm M3 (2 pcs)
1 x	11 mm Rubber pads (14 pcs)
1 x	Covered closure or fairings
1 x	Fully Threaded Steel Rod alumin 70 mm M2,5 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x	Allen wheel collar M3x5
1 x
1 x	M3 Maxi ball link (2 uds)
1 x	SPARK Switch 5.9v
2 x	SBEC Jeti
1 x	Turbina DRAGON 30 Kg
1 x	TP/TopFuel - XH 2/3S Adapter
1 x	M2,5 / 5Diam metal short ball link V3 (2 pcs)
1 x	Extension 2/3 lipos JST - JST/C
1 x	Long ball link M1.6 (6 uds)
1 x	M3 Maxi ball link (2 uds)
1 x	Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Ball link M3 (10 pcs)
1 x	PVC 0,25 qmm 4 line servos wire JR/Graupner (5 m)
1 x	SWTU2 switch
1 x	LA500 Autogyro
1 x	wing/fuselage connector for 6 pines AWG 20-24 (without pines)
1 x	Xoar Electric Beechwood Prop 20x10
1 x	Prolonguer for Balancer Thunder Power 6S
1 x	PWC6 PowerWingConnector for 6 servos with fuselage socket
1 x	TP/TopFuel - JST-EH 4/5S Adapter
1 x	PSC 5
1 x	Switching module high voltage SXH
1 x	PowerBox SparkSwitch RS
1 x	Turbo Prop KS
1 x	Interruptor RX/Batterie
1 x	Male prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Extension 2/3 lipos JST/C
1 x	Multi-adapter balancer JST - TP
1 x	Prolongador S-Bus JR/JR 10cm
1 x	silicon 100 cm Futaba Extension Ø 0,35 mm
1 x	Premium servo extension 50cm
1 x	Socket head long ball link M3 (2 uds)
1 x	Connector Sub-D 2+5 Male
1 x	Propeller electric carbon 10x7
1 x	Propeller POWER-PROP 14x10
1 x	Male connector for 20 pines AWG
1 x	SkyMaxx 1.550 mm (kit)
1 x	USBCOM 5i
1 x	Xoar Electric Beechwood Prop 21x10
1 x	AXI 2826/10 V2 Long
1 x	AXI 2808/16 V2 Long
1 x	AXI 2820/14 V2 Long
1 x	AXI 2826/8 V2
1 x	Motor OS 3820-1200 electric
1 x	AXI 2217/20 V2
1 x	SUS wire 3m (nylon coated)
1 x	Motor Mega AC 16/15/05 CE F5J
1 x	Indoor motor holder
1 x	Motor Advance 50-6
1 x	Motor Mega AC 16/15/07
1 x	Tip wing protector 28x10x12 (2 pcs)
2 x	Pushrod greyline 3/2 with coupler M2
1 x	Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x	Wheel collar 3.5 mm Ø (4 uds)
1 x	90 mm rods + T patellas set for direction control
1 x	Cable grommet 9.5 mm (4 uds)
2 x	Fully Threaded Steel Rod M2,5 (2 uds)
2 x	Allen wheel collar M4x6
1 x	Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x	Cable grommet Ø 4 mm (4 uds)
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x	AXI 2820/12 V2
1 x	AXI 2826/10 V2
1 x	AXI 2814/6D V2
2 x	Pushrod octagone 4/3 with coupler M3
1 x	Split M1,2x10 (10 pcs)
1 x	AXI 2814/16 V2 Long
1 x	Axle for AXI 4120/xx motors
1 x	Motor Mega AC 16/15/04 COMBAT
1 x	Motor Mega AC 16/15/04
1 x	AXI 2814/16 V2
1 x	Motor MVVS 5.6/690 GLIDER
1 x	Aluminun wheel collar 5 mm Ø (4 uds)
1 x	Tip wing protector 40x14 (2 pcs)
2 x	Pushrod octagone 3/2 with coupler M2
1 x	Aluminun wheel collar 2 mm Ø (4 uds)
1 x	Cable grommet Ø 5 mm (4 uds)
1 x	Aluminium cap bolt washer M3 black (8 pcs)
1 x	AXI 2212/26 V2
1 x	AXI 2826/12 V2 Long
1 x	AXI 2820/14 V2
1 x	AXI 2814/10 V2 Long
1 x	AXI 2820/12 CYCLONE
1 x	AXI 2826/12 V2
1 x	AXI 2826/6 V2
1 x	AXI 2808/20 V2
1 x	AXI 2217/20 V2 Long "F5J"
1 x	AXI 2217/16 V2 Long
1 x	AXI 2808/24 V2 Long
1 x	AXI 2826/8 V2 Long
1 x	Split pin 1.6x16 mm (10 uds)
1 x	Snap pin for micro clevis (10 uds)
1 x	Pushrod greyline 3/2 with coupler M3 L: 1000 mm
1 x	Radial Mount Set for AXI2814 and AXI2820 V2
1 x	Motor Mega AC 16/07/08
1 x	Motor Mega AC 22/20/03
1 x	Axle for AXI 2212/xx motors
1 x	Axle for AXI 5325/xx motors

19,625.88EUR