59.00EUR

Glases Innovation Plus
[CMINNOVATIONP]



Set de gafas, cristales, funda y trapo
Do you have to wear prescription glasses? Fed up with seeing your buddies turn up at the field with great looking and practical glasses you just can't wear? We have the answer in the form of these stylish prescription model flying sunglasses, which have been especially developed for radio control model use.

At the heart of the design is a polycarbonate frame that houses your prescription lenses; this clips onto a main frame, which in turn houses the coloured shades that simply clip on to a hinged section. These hinges allow you to temporarily turn up the outer lenses in order to closely inspect a model in the pits etc.

Innovation Plus are polarised sunglasses. The polarised cristals greatly reduce glare, which is an effect caused by light hitting horizontally flat surfaces. Polarised lenses filter out this light to greatly enhance your visibility.

The de-centred, scratch resistant lenses have been optically balanced to negate the effects their curvature would otherwise have on your vision. Conforming to US ANSI Z80.3 plus British and European safety standard EN1836, our sunglasses are factory impact-tested, and offer great protection against flying debris should you suffer a mishap. All of our glasses carry the CE (European Union standard) compliance mark. The interchangeable lenses are: yellow (category 1) low light - these actually enhance light and contrast; beige (category 2) average sunlight; smoked mirror (category 3) bright sunlight; dark smoked (category 4), very bright conditions.

The glasses come with the interchangeable lenses, a cleaning cloth and a superb carry case with belt clip. All frames and the carry case display our 'Model Glasses' logo.

WILL THEY WORK FOR ME? - If you have a prescription (SPH) requirement that's less than plus or minus 4.00, our glasses will work just fine for you. Stronger prescriptions can cause distortion, due to the curvature of the tinted lenses when placed in front of the flat prescription clip. The de-centring calibration loses its effect where stronger prescriptions are required. If you have a requirement greater than plus or minus 4, please do not buy these glasses. Bi-focals, varifocals and prismatic lenses can be added - if in doubt, please consult your optician for advice.

IMPORTANT NOTE
When wearing Innovation Plus, some users may find they cannot see certain types of LCD or other electronic / digital transmitter displays. This is a normal cause of wearing polarised glasses. We recommend using the glasses with the front section flipped up, or the glasses removed, when model trimming prior to use.


few units
few units

Reviews

Customers who bought this product also purchased
Tape GFK 50 mm
Tape GFK 50 mm

few units
few units

Tape GFK 25 mm
Tape GFK 25 mm

few units
few units

MAX BEC
MAX BEC

few units
few units

Fiberglass plate 350x150x0.5 mm
Fiberglass plate 350x150x0.5 mm

few units
few units

Connectors DEANS (T)
Connectors DEANS (T)

few units
few units

Conector FUTABA Servo male  (10 pcs)
Conector FUTABA Servo male (10 pcs)

few units
few units

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x Small Crow DLE-170M
2 x Propeller FALCON 32,5x11 PUSHER Carbono
1 x Motor DLE 430 cc - Paramotors
1 x Big Crow DLE-170M
1 x SE Ring 300 mm (2 pcs)
1 x 48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x ABS tube 18.0x16.0x1000 mm
1 x Z type of cable coupler Ø 2 (2 uds)
1 x Aluminium tube (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x Couple M4 for wire (10 pcs)
1 x Motor DLE 200cc Std
1 x 43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x Foil for sticking flaps and ailerons
1 x Steel tube (L 1000 mm Ø8 mm, Ø7,7 mm)
1 x Ball link duraluminium M3 V1 (10 pcs)
1 x Straightened rod Ø 4.0 mm x 1000 mm
1 x Strip ABS 2.0x5.0x1000 mm
1 x ABS Strip 1.5x6.0x1000 mm
1 x Straightened rod Ø 1.2 mm x 1500 mm
1 x Strip ABS 2.0x3.0x1000 mm
1 x Straightened rod Ø 14.0 mm x 1000 mm
1 x Starter Sullivan-STAR 603 DINATRON
1 x Profile ABS half cane 2.5x1000 mm
1 x Small aluminium horn red (2pcs)
1 x CA Glue fast 20g
1 x Carbon fiber rod 4.0 mmx1000 mm
1 x Plastic caps for AIR BURTS (30 pcs)
1 x Carbon fiber rod 8.0 mmx1000 mm
1 x 1/12 Pilot "Fighter"
1 x Locking cable tie 2.5x100 (uds)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x Green smoke canister 100 g
1 x Glases Nimbus
1 x Carbon fabric 245 g/m² (twill weave) 127 cm, roll/ 10 m
1 x Vacuum pump P1-N
1 x Brass control horn M4 short for wire (4 pcs)
1 x Support pump Xicoy X45
1 x 1/6 Pilot "John"
1 x Profile ABS half cane 7.0x1000 mm
1 x 2,0x50 mm allen screwdriver
1 x L cockpit anchor "tipe F3A" (2 pcs)
1 x Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 3 m
1 x Threaded coupler ALU M2 Ø 4 (2 uds)
1 x Carbon wing joinner 13,4 mm Ø 0,48 mm
1 x Adapter lead MPX/XT60
1 x CC 03
1 x 4 LiPo XH>EH adapter
1 x Extension silicon 25 cm (Graupner)
2 x Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x Futaba Female 40 cm extension
1 x Extension silicon 25 cm (Futaba)
1 x 3 LiPo XH>EH adapter
1 x ABS tube 3.0x2.0x330 mm
1 x Long pinned hinge (12 uds)
1 x 
1 x 26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x Blade Holder Full (4 blades)
1 x 20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x 4 blades set
1 x Steel tube (L 1000 mm Ø12 mm, Ø11,7 mm)
1 x 20x200 mm battery rings
1 x ABS tube 9.0x7.0x1000 mm
1 x Nylon hinge 20x20x0,3 (10 pcs)
1 x Actuador lineal HLS12-100210-7.4v
1 x 13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x SE Ring HACKER 300 mm (2 pcs)
1 x Pin type hinge Al 6x98 mm (2 pcs)
1 x Nylon hinge 15x0,3 (10 pcs)
1 x Aluminium tube with fibreglass case ø35x1.5mm, 1m
1 x Micro flex hinge (12 uds)
1 x Gates hinge
1 x 67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x 33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x ABS tube 8.0x6.0x1000 mm
1 x ABS Strip 1.5x3.0x1000 mm
1 x ABS Strip 1.0x2.0x1000 mm
1 x Round Rod 1,0x1000 mm
1 x Straightened threaded rod M2-1m
1 x Straightened rod Ø 1.5 mm x 1500 mm
1 x ABS I Strip 20x10x1000 mm
1 x Brass rod Ø 1.5 mm x 1000 mm
1 x ABS Strip 1.5x4.0x1000 mm
1 x Straightened rod Ø 2.0 mm x 1000 mm
1 x Round Rod 2,5x1000 mm
1 x Round Rod 1,25x1000 mm
1 x 1/6 Pilot "Garry"
1 x Profile ABS half cane 2.0x1000 mm
1 x Breatex™ Non-woven absorber 150 g/m² Roll 5 m
1 x Wing tips support for AX-18/AX-60 (2 pcs)
1 x Profile ABS half cane 4x1000 mm
1 x Stainless steel cable Ø 0.62 mm (10 m)
1 x PCARD Wireless System
1 x L-Connector 4.0 mm x 1000 mm
1 x Starter EM Gear Power 80
1 x Pilot "Anthony" (Slimline)
1 x Initior Receiver FRX2 Wireless
1 x 1/10 Pilot "Jimmy"
1 x Angle of incidence meter
1 x One touch canopy lock
1 x Carbon fiber rod 0.5 mmx1000 mm
1 x Civilian pilot "Pamela" size 9cm (Slimline)
1 x Initior Transmitter FTX2 Wireless
1 x 6 mm red aluminium threaded horn with patella
1 x Crimping sleeves for cable 1.3 mm (10 pcs)
1 x M2/M1/6 3Diam long black ball link V1 (6 pcs)
1 x 6 mm hexagonal ball link M3 (10 pcs)
1 x Bec MR UBEC 5A (5v/6v/7v)
1 x Short ball link M2 (6 uds)
1 x Ball link M3 RPA's-UAV's
1 x M2,5 5Diam short black ball link V2 (2 pcs)
1 x Breatex™ Non-woven absorber 150 g/m² Roll 20m
1 x M2/M1/6 3Diam long black ball link V1 (2 pcs)
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 10 m
1 x Extension silicon 50 cm (Futaba)
1 x Carbon fabric 160 g/m² (twill weave) 127 cm, roll/ 10 m
1 x Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x Aluminium red ball links M3 V1 (10 pcs)
1 x Crimping sleeves for 1.1 mm cable (10 pcs)
1 x ABS tube 5.0x3.0x1000 mm
1 x Tape GFK 50 mm
1 x 18 mm reinforced hinge
1 x Ball Link ALU M3 - RH (1 pcs)
1 x Pin type hinge Al 3,0x50 mm demount (2 pcs)
1 x Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x Aluminum Bayonet / strongal D25 mm / 1 m
1 x ABS tube 5.0x4.0x1000 mm
1 x Fast'n EZ-CA-Hinge, lite (12 uds)
1 x SE Ring 360 mm (2 pcs)
1 x Hard aluminium thin-walled tube with fibreglass case ø30x1mm, 1m
1 x ABS tube 12.0x10.0x1000 mm
1 x 10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x Threaded coupler Micro M2 Ø 0,8 (10 pcs)
1 x Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
1 x RUDDOG Protection and Heat Shield Tape (2mx50mm)
1 x ABS tube 3.0x1.0x1000 mm
1 x Threaded coupler M2,5 Ø 3 mm (10 pcs)
1 x Flap hinge (6 pcs)
1 x ABS tube 2.0x1.0x1000 mm
1 x Large flex hinge (12 uds)
1 x Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x Spikes Band (5 m)
1 x ABS tube 8.0x7.0x1000 mm
1 x SE Ring 480 mm (2 pcs)
1 x Marker ties (20 pcs)
1 x Small pinned hinge (12 uds)
1 x ABS tube 4.0x2.0x1000 mm
1 x Aluminium coupler M2/2 with ball bearing (1 pcs)
1 x Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x Silent-blocks DLE 170M
1 x Blade Holder (3 blades)
1 x Steel tube (L 1000 mm Ø5 mm, Ø4,7 mm)
1 x ABS tube 6.0x4.0x1000 mm
1 x Steel tube (L 1000 mm Ø10 mm, Ø9,7 mm)
1 x Gates hinge aluminium (1 pcs)
1 x Round Rod 4,0x1000 mm
1 x Straightened rod Ø 5.0 mm x 1000 mm
1 x Round Rod 5,0x1000 mm
1 x Straightened threaded rod M3 - 1m
1 x Strip 3,5x1,75x330 mm
1 x Strip ABS 2.0x8.0x1000 mm
1 x Straightened rod Ø 3.0 mm x 1000 mm
1 x Straightened rod Ø 5.5 mm x 1000 mm
1 x Brass rod Ø 1.0 mm x 1000 mm
1 x ABS I Strip 10x5x1000 mm
1 x Straightened rod Ø 1.0 mm x 1000 mm
1 x Strip 1,5x1,5x330 mm
1 x ABS Strip 1.5x8.0x1000 mm
1 x Strip 2,0x2,0x330 mm
1 x Strip ABS 2.0x10.0x1000 mm
1 x Round Rod 6,0x1000 mm
1 x ABS Strip 1.0x5.0x1000 mm
1 x Straightened rod Ø 0.8 mm x 1000 mm
1 x Strip 2,5x1,25x330 mm
1 x Brass rod Ø 0.8 mm x 1000 mm
1 x Brass hexagonal rod Ø 4 mm x 1000 mm
1 x Straightened rod Ø 7.0 mm x 1000 mm
1 x Smoke set "M"
1 x Militarian pilot "Kamikaze" size 9cm (Slimline)
1 x Ball Link Plier
1 x Canopy Lock V1 M3 Blue (2 pcs)
2 x Carbon fiber rod 1.5 mm x 2000 mm
1 x 
1 x Threaded coupler ALU Left M2,5 Ø 4 (2 uds)
1 x Glases Stratus
1 x Horn for flap control (1 pcs)
1 x Carbon fiber rod 1.5 mm x 1000 mm
1 x Profile ABS half cane 3x1000 mm
1 x AX-60 starters (5 pcs)
1 x Civilian pilot "Curt" size 9cm (Slimline)
1 x Rubber profile 6-2 mm 2M
1 x 1/6 Pilot "Buddy"
1 x Medidor ángulos y/o incidencias
1 x Brass control horn M2 short for wire (2 pcs)
1 x Profile ABS half cane 6.0x1000 mm
1 x Profile ABS Square 2 x 1000 mm
1 x Rubber profile 8-2 mm 2M
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x Canopy Lock V1 M3 Red (2 pcs)
1 x Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x Locking cable tie 3.2x142 (uds)
1 x 3l Smoke oil
1 x 2,5x60 mm allen screwdriver
1 x Carbon fabric 68 g/m² (style 493 aero, plain weave) 100 cm
1 x Dust collector for mould cleaning
1 x Civilian pilot "Joe" size 9cm (Slimline)
1 x Buy Perforated film 100 cm / 20 m
1 x Copier 2x20 cm pcs
1 x Horn 20x28,5 mm (2 pcs)
1 x LH long black aluminium horn L31xH30 (2pcs)
1 x Aro pasacable Ø25 mm (4 pcs)
1 x Screwdriver for Hexagon 1,5mm
1 x Red smoke bombs AX-60 (5 pcs)
1 x Horn 5/10 with M2 Bearing
1 x Squared carbon wing joinner 5x5x220 mm
1 x Carbon fiber rod 6.0 mmx1000 mm
1 x Tube support Ø 6mm (10 pcs)
1 x Cable with accesories
1 x Red smoke canister 100 g
1 x Blue smoke canister 100 g
1 x Pilot WWII US Navy Pacific 12" Scale 1/6-1/5
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (10 pcs)
1 x Crimping tool
1 x SIMtransmitter 6 Mode 2
1 x Support FUEL DOT V3
1 x Screwdriver for Hexagon 1,27mm
1 x Angle support XT60 conector
1 x Steering arm 16 mm Ø 4 mm
1 x AX-60 starters (5 pcs)
1 x Steering arm 12 mm Ø 3 mm (2 uds)
1 x Carbon fiber rod 0.5 mmx1000 mm
1 x Pilot "Adolf" Legends Series (Slimline)
1 x Cross Connector 4.0 mm x 1000 mm
1 x 6 mm blue aluminium threaded horn with patella
1 x Remote electric ignition system
1 x Threaded coupler ALU M3 Ø 5 (2 uds)
1 x PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x Threaded coupler ALU M2 Ø 3 (2 uds)
1 x Threaded coupler ALU M3 Ø 6 (2 uds)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
1 x Horn 6/35 with M3 Bearing
1 x Aro pasacable Ø20 mm (4 pcs)
1 x Ball Link Plier
14,147.48EUR
Manufacturers
Languages
Español English
Currencies