36.16EUR

Epoxy Casting Resin + Hardener "water-clear" (300 min)
[R1071023]


Epoxy Casting Resin + Hardener "water-clear" (300 min)

General information about the System Epoxy Casting Resin + Hardener "water-clear):
Two-component clear, colourless epoxy system.
The following properties distinguish it from the predecessor EP cast resin “crystal clear”:
Excellent UV resistance for epoxy resins*)
Supertransparent constituents
Polishable, hard surface
Excellent impact strength
Completely tackfree curing even in thin coats
Ideal for transparent coatings
Also suitable as a laminating resin system with a very long pot life
The system's reactivity was raised for smaller initial and casting quantities. An initial batch size of 400 g can be cast per mould without the surface collapsing. Casting thicknesses up to 40 mm are possible with larger initial quantities.

Like all reactive resin systems the casting quantity is limited by the generated reaction heat (exothermal reaction): often a lower curing temperature (e.g. at an ambient night temperature lower than 20 °C) can counteract too great an exothermal reaction.

Pot life : approx. 300 minutes

Mixing ratio:
100 : 37 parts by weight of resin to hardener
100 : 47 parts by volume of resin to hardener

Curing time: approx. 24–48 h

Processing:
Resin and hardener are homogenised for about two minutes at room temperature (23 °C). Afterwards the mixture is left to rest for approx. 20 minutes.
Leave the ready mixture on a flat surface for 48 hours. Please do not mix or otherwise move the product. The total curing time ranges from 24 to 48 hours.
Expertise for the resin system casting resin + hardener "water-clear": this system is not cytotoxic (cell damaging), important for applications in medical purposes!
*) This system has very good UV resistance for EP resins, but, like all epoxy resins, it can turn more or less yellow over time under high UV exposure. Therefore only conditionally suitable for outdoor applications or permanent exposure to artificial light sources.
Typical areas of application: Indoor: railway models, works of art, stage decorations, etc. (only occasionally exposed to UV sources).


temporarily out of stock
temporarily out of stock

Reviews
Categories
* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->
  
  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
    Cianocrylate->
    Epoxy->
      EMC-Vega
      KAVAN
      Loctite
      Resoltech
      Epoxy BSI
      Epoxy R-G
    Resin/Gelcoat
    Glass Bubbles
    Contact adhesive
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
3 x METEOR 1.000 mm kit
1 x Big-Malibu XL Roof box with surfboard rack GREY
1 x Motor DLE 200cc Std
1 x Motor DLE 200cc Premium Muffler
1 x Small Crow DLE-170M
1 x PIT (Aero-Naut)
1 x Screws flush mount M2
1 x Servo Fork
1 x Baering 3x8x4
1 x LA500 freewheel bearing
1 x Screw M3x16
1 x Sebart 2.2 m YELLOW/BLACK (SebART)
1 x Breatex™ Non-woven absorber 150 g/m² Roll 20m
1 x Epoxy L 40 min. 10 kg (Resin)
1 x CA Glue (medium) 20g
1 x Buy Perforated film 100 cm / 20 m
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x Epoxy 40 min (Resin). 25Kg
1 x Foam wheel Ø 38 mm (2 pcs)
1 x Reductora IPS 150 DX2BB-BXCS 7:1
1 x Servo HITEC D-955 TW Titanium
1 x HPP-21 PLUS PC and Field Programmer for Hitec Digital Servos
1 x Servo HITEC D950 TW
1 x Servo HITEC HS-5585MH
1 x Gear set HITEC HS-81
1 x Gear set HITEC HS-645MG/5645MG/5685MH
1 x Screws set for Hitec MG arms servo
1 x Gear set HITEC HS-56 HB
1 x Gear set HITEC HS-311/322/325BB
1 x Epoxy Resin L + Hardener L (40 min) 3.5 Kg (2.5 kg Resin L + 1 k
1 x Carbon fabric 245 g/m² (twill weave) 127 cm, roll/ 10 m
1 x Carbon fabric 160 g/m² (twill weave) 127 cm, roll/ 10 m
1 x Breatex™ Non-woven absorber 150 g/m² Roll 100m
1 x Epoxy 5 min. 500 g (Hardener)
1 x Breatex™ Non-woven absorber 150 g/m² Roll 5 m
1 x Breatex™ Non-woven absorber 300 g/m² Roll 41 m
1 x Mixing tube for double syringes and cartridges (MR 1:1 and 2:1)
1 x Epoxy 5 min. 200g
1 x 
1 x 
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 3 m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 2 m
1 x Carbon fiber rod 3.0 mm x 1000 mm
1 x Epoxy Casting Resin + Hardener "water-clear" (300 min)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (10 pcs)
1 x Carbon fiber rod 2.0 mmx1000 mm
1 x Epoxy adhesivo Elan-tech ADH 981.892 50ml (dark grey)
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 3m
1 x Foaming agent for epoxy resins 200 g
1 x Epoxy 10 min 190g
1 x Epoxy 40 min. 4kg (Hardener)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x Epoxy 40 min (Hardener). 1 Kg
1 x Epoxy Resin HT 2 + Hardener HT 2, kit/ 296 g
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 20 m
1 x Epoxy Resin L + Hardener GL 1 (30 min)
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x Carbon Fiber TeXtreme® 80 g/m² (plain) 100 cm, roll/ 10 m
1 x Alignment dowels (2 parts, outer-Ø 8 mm) bag/ 100 pairs
1 x Epoxy Resin L + Hardener L (40 min) 1Kg (715g Resin L + 285g Har
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 50 m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (10 pcs)
1 x Carbon fiber rod 1.5 mm x 2000 mm
1 x Epoxy Resin L + Hardener LT kit/ 895g
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x Propeller 8x4,3 SlowFlyer
1 x Reductora IPS 150 DX2BB-CXCS 8,6:1
1 x Cooler motor type 280
1 x Cooler motor type 150
1 x Cooler motor type 300
1 x 76 mm light wheels (2 pcs)
1 x Reductora IPS 150 DX2BB-FXCS 11,8:1
1 x Reductora IPS dual-motor 10,7:1 with spinner
1 x Cooler motor type 400
1 x Propeller 3x3
1 x Propeller 11x4,7 SlowFlyer
1 x Propeller 10x4,7 SlowFlyer
1 x Gear set HITEC D645 MW
1 x HPP-21 PLUS PC Programmer for Hitec Digital Servos
1 x 10-15mm Servo Arm
1 x Servo HITEC HS-325 BB
1 x 40 mm servo arm with bearing (2 pcs)
1 x Gear set HITEC HS-125MG/5125MG
1 x Servo HITEC D85 MG
1 x Servo HITEC HS-45 HB, servo box
1 x Servo HITEC HS-45 HB
1 x Gear set HITEC HS-55
1 x Servo HITEC HS-125 MG
1 x Gear carbonite set HITEC HS-6965
1 x 50 mm servo arm with bearing (2 pcs)
1 x Brazo servo aluminio 1.25/1.5" Futaba/MKS/Savox
1 x Servo BMS-4112
1 x Decorative caps, multicoloured
1 x Canopy Latch
1 x Distanzstück motor OS 120 AX
1 x DLE 55 Muffler
1 x DLE 85/111/120 Crankshaft keyway
1 x Muffler DLE-120 Left
1 x DLE 111 Old Crankshaft keyway
1 x Propeller MEJLIK 23x8 CFK
1 x FALCON 24X10 CARBON PROPELLER (GAS)
1 x ULTRA STICK 10 cc ARF
1 x PITTS CHALLENGER 87″ 2.20m (120cc) 02 ARF
1 x EDGE 540-A 91" (2310 mm)
1 x EXTRA NG 74" yello/blue/red (Skywing RC)
1 x Flap hinge 33x9 mm (6 pcs)
1 x Propeller G-Sonic 20x8
1 x Receiver replacement antenna, approx. 85
1 x 
1 x DLE Ignition 170M
1 x Big Crow DLE-170M
1 x Propeller POWER-PROP 16x8
1 x Propeller POWER-PROP 11x9
1 x 10x7 tree blades propeller
1 x FALCON 27X11 CARBON PROPELLER (GAS)
1 x FALCON 29X9 CARBON PROPELLER (GAS)
1 x Ball joint long
1 x SLICK 360-A 104" (2640 mm)
1 x CARBON CUB FX-3 100-200CC ARF, 165" - 4200 mm (Hangar9)
2 x BULLIT Wing 1095 mm
2 x BOOMERANG II 40/46 ARF 1.55mm
1 x Helice APC 14x4 W
1 x Propeller APC 10x4.7
1 x Propeller APC 12x10 Electric
21,901.70EUR
Manufacturers
Manufacturer Info
R-G.de
R-G.de Homepage
Other products
Languages
Español English
Currencies