129.90EUR

SAVAGE Max Red 1080 mm
[KAV02.8026]


A builder’s kit of 3D aerobatic park-flyer (1080 mm wingspan) made of virtually unbreakable thoroughly carbon reinforced EPP foam for 350-500W brushles motors. Symmetrical wing section, flat, large area fuselage for great 3D/knife edge handling. Aileron, elevator and rudder control.
SAVAGE MAX is a high performance 3D aerobatic park-flyer made of virtually unbreakable EPP foam for 350-500 W brushless motors. A couple of hours with a bottle of cyano are all you need to finish this model capable of classic pattern aerobatics as well as all 3D stunts! SAVAGE MAX is not just for skilled pilots; on small rates she could be flown by any Sunday flyer who already knows how to do a loop, stall turn and roll. And if something (or your fingers on sticks) goes wrong, thanks to the low all-up weight there usually is not much damage - and even if so, the EPP foam is so easy to repair!
The all-in-one wing EPP foam wing with symmetrical wing section is reinforced with a pair of carbon spars; the pre-cut bays are ready for your servos, indeed. The horizontal part of the fuselage is thoroughly reinforced by a web of carbon spars; the large area vertical part of the fuselage makes the knife edge easy. The plywood firewall is anchored to the foam fuselage with carbon spars as well; the pre-cut bays are ready to accommodate the elevator a rudder servos. The empennage is also made of the EPP foam; halves of the all-moving horizontal tailplane are glued to a carbon tube that rotates freely in 3D printed bearings in the fuselage. The control surface linkage is made of 3D printed horns, plastic clevises and short carbon or steel push rods. The carbon main undercarriage with lightweight foam wheels and EPP pants is secured by 4 bolts to a fibreglass plate anchored to the fuselage with 3D printed plastic holders. The steerable tail wheel assembly consists of 3D printed bracket and lightweight foam wheel.
You will need at least a four channel RC set; a computer radio featuring dual and exponential rates is strongly recommended.
SAVAGE MAX of a Sunday flyer would work nicely with analog micro servos with metal gears like KAVAN GO-13MG, Hitec HS-65MG etc. If you are serious about aerobatics even a little bit, you should go for high speed & torque digital servos like KAVAN GO-1013MG, Hitec HS-5065MG or similar.
We recommend KAVAN PRO 3536-1000, FOXY 3536-1000, Model Motors AXI 2814/16 V2 or similar brushless motors with the APC 11x4.7SF propeller if 3S LiPo battery was used or the APC 10x4.7SF with 4S LiPo.
At least 40A speed controller featuring a powerful switching BEC should be used - especially when high speed & torque digital servos are installed - like the KAVAN PRO-40SB or KAVAN R-50SB.
You can use 3S or 4S LiPo LiPo flight pack 1300-1800 mAh at least 40C.
Designed and manufactured in the Czech Republic.
The kit contents: printed parts of fuselage, wing, tail and wheel pants cut of EPP foam, plywood firewall, carbon spars, 3D printed plastic parts, horns, clevises, push rods and other small accessories, carbon undercarriage with light foam wheels, illustrated step-by-step instruction manual.
Wing span [mm] 1080
Length [mm] 1200
Weight [g] 850
Controlled functions S,V,K(2),M
Build difficulty S2
Operating difficulty P2,P3


Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Motor A2212/13T
2 x ABS angle 6,0x6,0x1000 mm
2 x Profile ABS half cane 4x2.5x1000 mm
2 x ABS rectangular profile 12x6.0x1000 mm
1 x Straightened rod Ø 0.5 mm x 1000 mm
1 x Medidor ángulos y/o incidencias
1 x Truck-trailer for gliders 720 x 239 mm
1 x Extension 100 cm (Futaba)
1 x Carbon fiber rod 4.0 mmx1000 mm
1 x Extension 90 cm (Futaba)
1 x Carbon rectangular rod 10.0 mm x 1.0 x 1000 mm
1 x Propeller balancer
1 x Carbon fiber rod 10 mm x 1000 mm
1 x Carbon fiber rod 7.0 mmx1000 mm
1 x Carbon fiber rod 2.5 mmx1000 mm
1 x Carbon fiber flat 1000x3.0x0.5 mm
1 x 200 mm extensión servo HITEC/JR
1 x Carbon fiber rod 6.0 mmx1000 mm
1 x Extension silicon 50 cm (Futaba)
1 x Cable S.BUS 3 salidas 300 mm
1 x Cabel "Y" 30 cm (graupner)
1 x Extension lead 15 cm Multiplex
1 x Xoar Electric Beechwood Prop 22x10
1 x Cable tie mounts 4.3 (4 uds)
1 x Allen wheel collar M3x3
1 x Cabin latch Fox MDM1 4m (pair)
1 x 280 cc gasoline fuel tank complet
1 x Foaming agent for epoxy resins 200 g
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x CA Glue fast 20g
1 x Ball Bearing Oil 25 ml
1 x Birch plywood plate 600x300x2.5 mm
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x Aluminium cap bolt washer M4 red (8 pcs)
1 x aluminium servo arm V2-JR 2,0 inch M3
1 x 12 mm floating pad (49 pcs)
1 x 10 mm Quick clamp_L (6 pcs)
1 x Aluminium cap bolt washer M3 green (8 pcs)
1 x 6 mm Quick clamp_S (10 pcs)
1 x ABS "T" angle 8.0x8.0x1000 mm
1 x Profile ABS Square 1 x 1000 mm
1 x Profile ABS triangular 2.0x1000 mm 90º
1 x ABS rectangular profile 10x5.0x1000 mm
1 x ABS "T" angle 6.0x6.0x1000 mm
1 x ABS angle 10,0x10,0x1000 mm
1 x Profile ABS triangular 6.0x1000 mm 90º
1 x ABS "T" angle 10.0x10.0x1000 mm
1 x Profile ABS half cane 3x1000 mm
1 x ABS angle 4,0x4,0x1000 mm
1 x ABS angle 2,0x2,0x1000 mm
1 x Streamline Stainless Steel Tubing 10.5x5.7x1000 m
1 x Aluminium rod Ø 4.0 mm x 3000 mm
1 x Straightened rod Ø 1.2 mm x 1500 mm
1 x Straightened rod Ø 14.0 mm x 1000 mm
1 x Straightened rod Ø 8.0 mm x 1000 mm
1 x Cabel "Y" 30 cm (Futaba)
1 x Carbon fiber rod 1.5 mm x 1000 mm
1 x Extension silicon 25 cm (Futaba)
1 x Carbon fiber rod 1.0 mm x 1000 mm
1 x 800TVL CMOS camera for FPV
1 x Carbon fiber rod 16 mm x 1000 mm
1 x Squared carbon wing joinner 5x5x220 mm
2 x 11 mm Rubber pads (14 pcs)
1 x Aluminun wheel collar 6 mm Ø (4 uds)
1 x Allen wheel collar M4x6
1 x PT 21x13 EL Propeller 3 Blade
1 x Clip fixing for wing (2 pcs)
1 x Aluminium alloy coupler for carbon tube 6/M4
1 x Aluminun wheel collar 4 mm Ø (4 uds)
1 x Ferrita 14x8x5.5 mm
1 x 100 mm rods + T patellas set for direction control
1 x Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x Epoxy L 40 min. 10 kg (Resin)
1 x Hardener EPIKURE™ Curing Agent MGS™ LH285, bottle/ 800 g
1 x Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x Conector MR-60 (pareja)
1 x Cyanocrylate MD GA460 odourless 20g
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x Brazo servo KAVAN doble aluminio 25T - 2.5" M3
1 x Crawler GRE-24 RTR 1:24 Arena
1 x Aluminium wide washer M3 blue (4 pcs)
1 x aluminium servo arm V1-JR 1,0 inch M2
1 x Profile ABS half cane 2.0x1000 mm
1 x ABS angle 5,0x5,0x1000 mm
1 x Cross Connector 4.0 mm x 1000 mm
1 x Rubber profile 10-2 mm 2M
1 x ABS angle 1.5x1.5x1000 mm
1 x ABS "T" angle 4.0x4.0x1000 mm
1 x L-Connector 1.0 mm x 1000 mm
1 x Profile ABS half cane 8.0x1000 mm
1 x Profile ABS half cane 5.0x1000 mm
1 x Flat Connector 4.0 mm x 1000 mm
1 x L-Connector 4.0 mm x 1000 mm
1 x Profile ABS Square 3 x 1000 mm
1 x Straightened rod Ø 1.0 mm x 1000 mm
1 x Straightened threaded rod M3 - 1m
1 x Straightened rod Ø 2.5 mm x 1000 mm
1 x Straightened rod Ø 4.5 mm x 1000 mm
1 x Carbon fiber rod 1.5 mm x 2000 mm
1 x Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm
1 x Carbon fiber rod 12 mm x 1000 mm
1 x Extension silicon 30 cm female (Graupner)
1 x Extension silicon 35 cm (Futaba)
1 x Extension silicon 25 cm (Graupner)
1 x Extension 15 cm (Futaba)
1 x Field folding model stand SebArt
1 x Extension silicon 75 cm (Futaba)
1 x Cable silicona macho batt. receptor 30 cm (Futaba)
1 x USB Mini Camera endoscope
1 x Carbon wing joinner 13,4 mm Ø 0,48 mm
1 x Carbon fiber rod 20 mmx1000 mm
1 x Extension silicon 100 cm (Graupner)
1 x 0,14 mm PVC servo wire extension, ZH micro conector.
1 x Carbon fiber rod 14 mmx1000 mm
1 x Extension silicon 10 cm (Futaba)
1 x WingFix ULTRA Black Edition
1 x Extension PVC 150 cm (Graupner)
1 x Extension 30 cm (Futaba)
1 x Carbon fiber rod 8.0 mmx1000 mm
1 x Extension 7.5 cm
1 x Carbon fiber rod 0.5 mmx1000 mm
1 x Propeller balancer
1 x Extension silicon 75 cm (Graupner)
1 x Extension silicon 30 cm female (Futaba)
1 x Futaba Female 40 cm extension
1 x Carbon fiber flat 1000x6.0x0.8 mm
1 x Extension silicon 10 cm (Graupner)
1 x Cable S.BUS 3 salidas 100 mm
1 x Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x Extension silicon 50 cm (Graupner)
1 x Futaba Female 40 cm extension
2,014.67EUR
Manufacturers
Manufacturer Info
Kavan
Other products
Languages
Español English
Currencies