4.50EUR

CA Glue fast 20g
[R1501032]


CA Glue fast 20g
Superglue (fast) is a normal type Cyanoacrylate adhesive with fast setting, high flow abilit, and good penetration characteristics.

It has been specially formulated to achieve the strongest possible bond between well-mated, non-porous surfaces, such as rubber, metals, plastics, glass, etc.

Single-component
Transparent
Very low viscosity, high setting speed
Bonds obtain hand strength after 2-15 seconds
Special bottle*
*A metal needle is fitted in the lid, which is pressed into the opening of the bottle's dosing attachment when it is screwed on. This reliably prevents leakage, drying out and sticking of the opening. The dosing attachment allows a fine dosing of the adhesive.

Physical properties
Liquid state
Base Ethyl Cyanoacrylat
Colour clear
Specific Gravity (at 20 °C) 1.053~1.060
Refraction Index (n 20 D) 1.439
Flash Point (°C) >80 °C
Boiling Point (°C) 65/6mm Hg
Viscosity (cP) 3-5
Cured state
Colour clear
Specific Gravity (at 20 °C) 1.1~1.3
Processing temperature -55 - 80 °C
Refraction Index (n 20 D) 1.49
Dielectric Constant (bei 10 MHz) 3.5
Dielectric Loss (bei 10 MHz) 0.067
Soluble in Acetone, Dimethyl formamide,Nitromethame and Dimethyl sulfoxide.
Bond strength (Tensile shear strength, cured for 24 hours at 20-25 °C)
kg/cm²
Rigid PVC to rigid PVC 40-60
ABS to ABS 50-70
Polycarbonate to polycarbonate 80-120
Polystyrene to polystyrene 30-45
Natural rubber to natural rubber 5-9
Steel to steel 190-210
Stainless steel to stainless steel 200-220
Aluminum to aluminum 160-180
Copper to copper 150-170
Steel to rigid PVC 50-60
Stainless steel to neoprene 5-10
SBR to SBR 5-10
Cure speed
Seconds
ABS to ABS 4-5
Wood to wood 50-60
ABS to stainless steel 5-10
NBR to stainless steel 3-5
NBR to NBR 3-5
Stainless steel to stainless steel 3-5
ABS to NBR 3-5
Wood to ABS 5-10
Storage and shelf life:
Our superglue can be stored in a cool and dark place for about 1 year (for example in the refrigerator at + 5 °C).
At room temperature about 6 months. At temperatures above 20 °C the shelf life is further reduced (e. g. in the summer months)


temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
Extension MPX-MPX 20 cm
Extension MPX-MPX 20 cm

temporarily out of stock
temporarily out of stock

Sparkplug NGK CM6
Sparkplug NGK CM6

temporarily out of stock
temporarily out of stock

TYGON tubo 1 m Diam. 3.4 x 2.0  mm
TYGON tubo 1 m Diam. 3.4 x 2.0 mm

temporarily out of stock
temporarily out of stock

Tygon tube 6.35 - 3.18 mm 1m
Tygon tube 6.35 - 3.18 mm 1m

temporarily out of stock
temporarily out of stock

Propeller MENZ-S 23x8
Propeller MENZ-S 23x8

temporarily out of stock
temporarily out of stock

Aluminium tube (L 1000 mm, Ø4.0 mm, Ø3.1 mm)
Aluminium tube (L 1000 mm, Ø4.0 mm, Ø3.1 mm)

temporarily out of stock
temporarily out of stock

Categories
* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->
  
  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
    Cianocrylate->
      BSI Cianocrilates
      Cyanocrylate R&G
      KAVAN Ciano
      Yuki Model
    Epoxy->
    Resin/Gelcoat
    Glass Bubbles
    Contact adhesive
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x PowerFuel RX V2 Fuel Pump
1 x PowerBox Smokepump JETs 2x outside
2 x JM electric Pump
1 x PowerBox Smokepump
2 x Electric Fuel Pump 12v
1 x Smoke pump RCEXL
1 x Variable Flow Smoke Pump System
1 x KAVAN Hand crank fuel pump
3 x Secraft Fuel system v2, red color
1 x Conector FESTO G1/8 Quick 4mm 90º
1 x FESTO connector M7 barb fitting XL Tygon
1 x Straightened rod Ø 2.5 mm x 1000 mm
1 x Horn 6/20 with M3 Bearing
1 x Extension PVC 150 cm (Graupner)
1 x Ring 320 mm length (5 pcs)
1 x 
1 x Copier 5x20 cm pcs
1 x Fresa corte diamante Ø 2.35mm (lentil)
1 x Digital precision scale up to 2000 g
1 x Aramid fibre shears Proton®, 21 cm / 8" length
1 x Dremel PERMAGRIT 18 mm round lime
2 x 25 mm Sandpaper file
1 x Extinguisher CO2 - 2 Kg
1 x M3 Maxi ball link (2 uds)
2 x Carbon fiber flat 1000x3.0x0.13 mm
1 x Red smoke canister 100 g
1 x Socket head ball link M3 (2 uds)
1 x White smoke canister 100 g
2 x Carbon fiber rod 20 mmx1000 mm
1 x Adapter lead MPX/EC3
1 x "S" set for boats
1 x Tube Pitot to PIXHAWK
1 x Smoke set "Glider"
1 x Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
1 x Micro flex hinge (12 uds)
1 x Flap hinge 33x9 mm (6 pcs)
1 x Nylon hinge 20x20x0,3 (10 pcs)
1 x Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
1 x Threaded coupler Micro M2 Ø 0,8 (10 pcs)
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x Z type of cable coupler Ø 1 (2 uds)
1 x Miniature brass strap hinge, 1 m
2 x Pin type hinge Al 3,0x50 mm demount (2 pcs)
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x Glass fabric tape 225 g/m² (Silane, plain) 30 mm X 100m
1 x Large flex hinge (12 uds)
1 x Ball Link ALU M3 - RH (1 pcs)
1 x Threaded coupler Micro M2 Ø 0,8 mm (10 pcs)
1 x Ball link Aluminio M3 (2 pcs)
1 x Couple M4 for wire (10 pcs)
1 x 67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (10 pcs)
1 x Carbon fibre sleeve 12k 170 mm x 5m
1 x Clevis plastico I=45 mm / hole 3mm / pin 1 (2 pcs)
1 x Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x Threaded coupler ALU M2 Ø 4 (2 uds)
1 x Unmounted aluminium pin 6x98 mm (2 pcs)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
2 x Aluminium coupler M2/2 with ball bearing (1 pcs)
1 x Nylon hinge for flaps 33x9 (2 pcs)
1 x Carbon Non-Woven, 160 g/m² 127 cm 1 m
1 x Ball link Aluminio M3 (6 uds) 27x11.9x5.9 mm
1 x Kavan Car 25% nitro 1l
1 x 120x60 mm SLH KOVO wheel
3 x Bags BULL Mo1 2.6m "Luxe"
1 x Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
2 x Tank BULL MØ1 3L+14L Smoke (CMJets)
1 x Marker ties (20 pcs)
1 x USB interface ALTIS
1 x Aluminium cap bolt washer M4 red (8 pcs)
1 x Blue aluminium servo arm V1-Hitec 1,5" inch M3
1 x Interruptor RX/Batterie
1 x Female connector JST SH 1.0mm with 10 cm wire
1 x CC 05
1 x Blue aluminium servo arm V1-Hitec 1,0" inch M2
1 x Receiver bed (Blue)
1 x Carbon wing joinner 13,4 mm Ø 0,48 mm
1 x Threaded coupler ALU M2,5 Ø 3 (2 uds)
2 x RX external cable for estandar receivers
1 x Baseplate servo
4 x RX cabel
1 x Y Cable
2 x Set transmisions BULL Mo1 (dura/aluminium)
1 x Pipa 3D BULL MØ1 2.600mm
1 x Tank BULL MØ1 4L (CMJets)
1 x Tank BULL MØ1 (3.2 L) + 1x (0.9 L) + 1x (0.9L Smoke) PRO
3 x GPS Expander Module
2 x Electric Landing Gear GS-200 BULL Mo1 2.6 (Elektron Retracts)
2 x 800TVL CMOS camera for FPV
1 x GPS Logger Dymond
2 x Aluminium wide washer M3 gold (4 pcs)
1 x Servo Mount S (red)
1 x M3/5 Diam metal short ball link V3 (2 pcs)
1 x Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
2 x Red aluminium servo arm V1-Futaba 23 mm M2
2 x Servo Mount M (blue)
1 x Extension 2/3 lipos JST - JST/C
1 x Optical RPM Sensor
1 x Aluminium wide washer M4 Black (4 pcs)
1 x Female connector for 6 pines AWG
1 x Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x Black copper lacquer wire Ø0,2 mm (5 m)
1 x Extension 5 lipos JST - JST/C
1 x Rudder 2_Tray 3~3.5 inch
1 x Male Prolonger TP 4/5S
1 x Aluminium wide washer M4 Blue (4 pcs)
1 x Aluminium cap bolt washer M4 green (8 pcs)
1 x Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x Red aluminium servo arm V1-Futaba 1,5" inch M3
1 x Red aluminium servo arm V1-Futaba 1,25" inch M3
1 x Aluminium cap bolt washer M3 red (8 pcs)
1 x Male connector JST SH 1.0mm with 10 cm wire
1 x PSC 5
1 x Carbon fiber rod 16 mm x 1000 mm
1 x Thermoforming sheet 0.3mm (0.039in) DIN A4
1 x Aluminium coupler M2,5/2 with ball bearing (1 pcs)
1 x Release film 100 cm x 50 m
2 x Carbon fiber rod 0.5 mmx1000 mm
1 x Sandwich carbon + poplar 2mm + carbon 290x160 mm
1 x Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x Threaded coupler ALU M2,5 Ø 6 (2 uds)
2 x Carbon fiber rod 2.5 mmx1000 mm
1 x 25 mm reinforced hinge
1 x Medidor ángulos y/o incidencias
1 x Truck-trailer for gliders 720 x 285 mm
1 x Angle of incidence meter
1 x Field folding model stand
1 x Surface Indicator Gauge Small
1 x Propeller balancer
1 x Propeller balancer
1 x Oracover Azul 2 m
1 x ORACOVER Ferrari red (2 m)
1 x Carbon fiber flat 1000x3.0x1.0 mm
1 x Stickers-digit for marking
1 x Fast'n EZ-CA-Hinge (12 uds)
1 x 67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x 48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x 15 mm reinforced hinge
1 x Pin hinge 26x11 mm (10 uds)
1 x 43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x Pin hinge 34x16 mm (10 uds)
1 x Sandwich carbon + poplar 2mm + carbon 480x290 mm
1 x Strip 2,5x1,25x330 mm
1 x ABS Strip 1.0x4.0x1000 mm
1 x L-shaped servo mount
1 x Angle measurer
1 x Field folding model stand SebArt
1 x WingFix ULTRA Black Edition
1 x 105 mm PVC transparent battery termo-retract 68 mm (1 m)
1 x 6,4x1000 mm 2:1 black termoretract tube
1 x 6,4x1000 mm 2:1 green termoretract tube
1 x Monokote BLUE metalizado (1.8x0.65m)
1 x MYLAR film A350 (1000x500 mm)
1 x ABS Strip 1.5x6.0x1000 mm
1 x ABS Strip 1.0x2.0x1000 mm
1 x ABS I Strip 20x10x1000 mm
1 x Round Rod 1,0x1000 mm
1 x Radial mount for electric 2.5-5.6
1 x Wheel FEMA 100 mm / 6 mm
1 x SLICK 103" Yellow/Blue ARF (Color 2) 2630 mm
1 x Wheel FEMA 82 mm / 5 mm
1 x A60-6XS V4 28-Pole
1 x Wheel FEMA 127 mm / 6 mm
1 x Compact on-board starting system (9512)
1 x Brake for 140 mm wheels
1 x Compact on-board starting system (9724)
1 x Wheel FEMA 140 mm / 6 mm
1 x ESC ALPHA 60A HV
1 x CC 11 Conector
1 x Quick hose connector 3-3 mm
1 x Motor holder AXI
1 x OS 37 SZ-H, Piston
1 x OS 37 SZ-H, Bulon piston
1 x Oracover Black 10 m
1 x Carbon fiber rod 1.0 mm x 1000 mm
1 x Carbon fiber rod 7.0 mmx1000 mm
1 x Fully Threaded Steel Rod Duralumin 40 mm M3 (2 pcs)
1 x DSM 10 Dual Switch Mixer
1 x DUPLEX 2,4GHz MRPM-AC EX
1 x Electric Landing Gear "Black Edition" BULL Mo1 2.6 GS200 (Electr
1 x Copier 2x20 cm pcs
1 x Futaba 52 mm servo arm
1 x Female connector for 10 pines AWG
1 x USB Mini Camera endoscope
1 x Rudder 2_Tray 4.5~5 inch
1 x Aluminium wide washer M3 blue (4 pcs)
1 x Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm
1 x Aluminium blue ball links M3 V1 (10 pcs)
1 x Aluminium wide washer M4 Red (4 pcs)
1 x DUPLEX 2.4EX Central Box 210
1 x Wing Joiner BULL MØ1 2.600mm
1 x Gyro 3-Ejes REFLEX V2 FMS
1 x Fuselage BULL MØ1 2.600mm
1 x Male connector for 20 pines AWG
1 x HITEC 20 mm servo arm with ball link
1 x Gates hinge
2 x DUPLEX 2.4EX Central Box 220
1 x Carbon fiber rod 1.5 mm x 2000 mm
1 x Fully Threaded Steel Rod Duralumin 34 mm M3 (2 pcs)
1 x Carbon rectangular rod 10.0 mm x 1.0 x 1000 mm
1 x Aluminium cap bolt washer M3 black (8 pcs)
1 x Red aluminium servo arm V1-Futaba 1,0" inch M2
1 x Carbon plate 350x150x1.0 mm
1 x Brass ball links BS M3 V1 (10 pcs)
1 x Carbon fiber rod 12 mm x 1000 mm
1 x Rudder 2_Tray 4~4.5 inch
1 x M3 Maxi ball link (2 uds)
1 x Red aluminium servo arm V1-Futaba 17 mm M2
1 x Carbon fiber rod 4.0 mmx1000 mm
1 x Aluminium cap bolt washer M3 blue (8 pcs)
1 x Battery RX JETI LiIon RB 3100 7.2v
1 x Black tray 2,4EX DC-16/14/24 black
1 x DUPLEX 2.4EX MU 3 Sensor
1 x DUPLEX 2,4EX Switch SAFETY 2-Position Safety DC-16/14
1 x DUPLEX 2.4EX Central Box 220 + 2x Rsat2
1 x Battery RX JETI LiIon RB 2600 7.2v
1 x Sun Cover BULL Mo1 2.6 (Hispano Aviacion)
1 x 2,0x50 mm allen screwdriver
1 x PowerBox OLED display
1 x Electric Landing Gear BULL Mo1 2.6 (Elektron Retracts)
1 x Canopy BULL MØ1 2.600mm
21,517.08EUR
Manufacturers
Manufacturer Info
R-G.de
R-G.de Homepage
Other products
Languages
Español English
Currencies