88.70EUR

NF-3X-80 liner Kit
[NF-3X-80Liner]


NF-3 X is a unit designed for illumination of models with spread up to l.7 metres for flying at night. lt is used to power colour ultra bright LEDs (Light-Emitting Diode) It contains six independent current-powered outputs. Five outputs are powered with the nominal current of 20 mA. Two outputs are for position lights (P1, P2), two independently flashing ones for the anti—collision flash lights (F1, F2), and one output for the landing lights (L1). The sixth output (L2) is designed to power the landing headlight of 80, 150 or 350 mA (according to the respective type). Operation of the output L2 is one second delayed to the output L1. That produces an effect of phased switching by the pilot.

The unit offers eight different flashing combinations ( 0 -7 ) with one second period for F1 and F2 outputs. One of those combinations can be selected by couplers (jumpers) 1, 2, 4. The sum of numbers ofthe connected couplers represents the number of the selected combination. The unit can be used as controlled or non-controlled by pilot. lf controlled by pilot, the jumper "3p" allows you to select between 2-positions (Fly/Landing) or 3—positions (Off/Fly/Landing) control by the remote controller. With a 2-positions control the position and anti-collision lights start work when the unit is connected to the accumulator. However, the landing lights can be switched on and off by pilot. ln the 3-positions control system, all lights are off in the off-position. ln the fly-position the position and anti-collision lights are on and in the landing-position, all lights are on.
Unit is in non-controlled mode if the Rx cable is not connected to the receiver. ln this case the lights start work when the unit is connected to the accumulator and the "3p" jumper can be used to switch manually the landing lights off. Anti-collision and landing lights automatically begin to flash when the plane is unable to receive a signal from the remote controller. The receiver circuit and the light circuits are electrically separated by an opto-coupler. Unit is compatible with Graupner or Hitec type connectors.
The outputs maintain the nominal current in the wide range of voltage from 6V to 14V without the need to connect compensating resistance series in the circuit. The stabilization starts working from 4.5V, therefore it is possible to connect the unit with the used NiCd or NiMH batteries with 5 up to l0 cells or Li-Pol from 2 up to 3 cells. As the number ofthe cells of the powering accumulator increases, so does the number of diodes that can be connected (serially) in one circuit.

The NF-3X-80 Liner Set, besides control circuit, includes 1x5 mm 20 mAh green LED, 2x5 mm 20 mAh red LEDs, 6x5 mm 20 mAh white LEDs and 2x 25 mm 80 mAh white LED's


temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
Transmitter Balancer Futaba T-10CG
Transmitter Balancer Futaba T-10CG

temporarily out of stock
temporarily out of stock

Extension silicon 75 cm (Futaba)
Extension silicon 75 cm (Futaba)

temporarily out of stock
temporarily out of stock

Extension silicon 50 cm (Futaba)
Extension silicon 50 cm (Futaba)

temporarily out of stock
temporarily out of stock

Servos security connector (2 pcs)
Servos security connector (2 pcs)

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Transmitter Crystal 35 Mc/s Ch 77
1 x Vest clothes Hispano Aviación
1 x Carbon plate 350x150x3.0 mm
2 x Propeller APC 12x6 Electric
1 x Glases Aspen
1 x Premium servo extension 50cm
1 x Ply-Span 450x600/13g Yellow
1 x 14x60 mm Mini rings Tie Wraps (4 pcs)
1 x Extension silicon 30 cm female (Futaba)
1 x Extension silicon 10 cm (Graupner)
1 x Oracover Orange 2 m
1 x Connector CAN 15
1 x Extension 30 cm (Futaba)
1 x Futaba Female 40 cm extension
1 x Propeller APC 11x5.5 Electric Pusher
1 x Cabel "Y" 30 cm (Futaba)
1 x Foil for sticking flaps and ailerons
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 2 m
1 x 0,14 mm PVC servo wire extension, ZH micro conector.
1 x 20x200 mm battery rings
2 x Propeller APC 10x5 Electric Pusher
1 x servo adapter lead, JST-SH socket - JR male Pin, for GR-12SH+HoT
1 x Propeller APC 10x3,8 SF
1 x Socket head ball link M3 (2 uds)
1 x Vasa model Catapult
1 x 26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x TeXtreme® Carbon tape 38 g/m² (IM, unidirectional) 20 mm x 100m
2 x Oracover White 10 m
1 x M2/M1/6 3Diam short black ball link V1 (2 pcs)
1 x 19.5x13 Falcon electric 3-Blade carbon prop (54 g)
1 x Propeller APC 12x8 Electric
1 x Glases Nimbus "Black"
1 x Brass rod Ø 1.0 mm x 1000 mm
1 x Connectors banna oro 4 mm (M/F)
1 x Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x Oratex Natural White 2m
1 x Tape GFK 38 mm
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x Conector Servo female 4 pines
1 x Straightened rod Ø 3.0 mm x 1000 mm
1 x Brass rod Ø 0.5 mm x 1000 mm
1 x Connectors banna gold 5,5 mm (M/F)
1 x Profile ABS half cane 2.0x1000 mm
1 x Xoar Electric Beechwood Prop 16x7
1 x Straightened rod Ø 5.0 mm x 1000 mm
1 x Connectors banna oro 8,0 mm (M/F)
1 x Carbon roving DowAksa / 24k / 1600 tex
1 x Gold antispark 5,5 mm plug
1 x Glases Moritz
1 x Short ball link M3 (6 uds)
1 x ABS angle 1.5x1.5x1000 mm
1 x silicon 100 cm Futaba Extension Ø 0,35 mm
1 x 5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x Brass hexagonal rod Ø 3 mm x 1000 mm
1 x Propeller 12x6 Falcon electric
1 x Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x Zurich Sport Sunglasse Dark Sensity BROWN Glasses
1 x Oracover Azul 2 m
1 x Connectors banna oro 0,8 mm (M/F)
2 x Ply-Span 450x600/13g Blue
1 x ABS angle 4,0x4,0x1000 mm
1 x Propeller APC 10x6 Electric Pusher
1 x Propeller 8x4,3 SlowFlyer
1 x Propeller APC 27x13 Electric
1 x Propeller APC 10x4.7 SF
1 x Beech dowels 10 mm x 1000 mm
2 x BALSA triangular 8x8x1000 mm
1 x Pine wood slat 2.0x10.0x1000 mm
1 x Propeller APC 10x6 Electric
1 x M2,5 Diam metal short ball link V3 (2 pcs)
1 x Propeller APC 10x4.7 SF Pusher
1 x Propeller APC 10x7 Electric
1 x Pine wood slat 3.0x10.0x1000 mm
1 x Propeller APC 12x6 Electric Pusher
1 x Propeller APC 10x5.5 MR Electric multirrotor PUSHER
1 x BALSA trip 2.0x2.0x1000 mm
1 x Propeller APC 8x3,8 SF Electric Pusher
1 x Propeller APC 9x4.5 Electric Pusher
1 x Propeller APC 9x7.5 SF
1 x Propeller APC 4.75x4.5
1 x Propeller APC 4.7x4.2
1 x Propeller APC 9x6 Electric
1 x Propeller APC 7x4 SF
1 x Propeller APC 13x4 Electric Pusher
1 x Propeller APC 11x8 Electric
1 x Propeller APC 10x4.7
1 x Ball link M3 RPA's-UAV's
1 x Pine wood slat 10x10x1000 mm
1 x Liston HAYA 8 x 8 x 1000 mm
1 x Pine wood slat 6.0x6.0x1000 mm
1 x Liston HAYA 10 x 10 x 1000 mm
1 x Beech dowels 3.0 x 1000 mm
1 x Propeller APC 11x8.5 Electric
1 x BALSA trip 3.0x5.0x1000 mm
1 x Propeller APC 11x7 Electric
1 x Socket head ball link M3 (2 uds)
1 x Propeller APC 13x6.5 Electric Pusher
1 x Mould Resin P 10 kg
1 x Epoxy Resin L 285 + Hardener 285 (Aero), kit/ 2.8 kg
1 x Conector MT-60 (pair)
1 x Monokote BLANCO jet (1.8x0.65m)
1 x Propeller APC 20x12 WE Electric
1 x Propeller APC 18x12 Electric
1 x Epoxy Resin HT 2 + Hardener HT 2 (60 min) 1 kg
1 x Oracover CHROME 2m
1 x XT-90 connector (pair)
1 x Bungee HLG Premium
1 x Propeller APC 14x8.5 Electric Pusher
1 x Propeller APC 20x13 Electric
1 x Connectors banna oro 8,0 mm 5 pcs(Female)
1 x Mould Resin P + Hardener EPH 161-P, kit/ 585 g
1 x Jet Afterburner Simulator NF-Jet2
2,666.71EUR
Manufacturers
Manufacturer Info
Night Fly
Night Fly Homepage
Other products
Languages
Español English
Currencies