54.24EUR

NF-3 RC set
[NF-3RC Set]



Funcionamiento del NF-3

Esquema de conexi�n
NF-3RC extends the capabilities of the NF-2RC unit with a greater number of circuits and more flash lights regimes. Just as NF-2RC it has two position lights circuits. It has also two landing lights circuits and two flash light circuits. Switching on/off of the second landing lights circuit is delayed by 1 second against he first circuit. That produces an effect of phased switching by the pilot. Eight different combinations of flashing can be selected for the two flash light circuits. Three couplers (jumpers) are used for selection.

One second is split into 16 parts. It is possible to set during which parts the light should be on (1) and off (0) to both flash circuits. Such a couple of sequences of 16 ones and zeros represents one combination of flashes. Eight such combinations (couples of sequences) are saved in the unit. By default, the unit contains six combinations of 1, 2 and three mutually shifted flashes plus two flashing modes 1:1, one with the period 1s, the other twice faster. The last two regimes are designed especially for helicopters owners.

A coupler is used for selection of 2- and 3-positional control regime as in NF-2RC. If the 2-position control is selected, in the first position the position and ant-collision lights light, in the second position the landing lights get switched on, too. In the three-position regime, in the first position, all lights are off, in the second position the position lights and anti-collision flash lights are on and in the third position, all lights are on. The unit can be used also in no-control mode. In that mode, position and flash lights are permanently turned on and the coupler for regime selection switches the landing lights.

Thanks to a galvanic separation of the receiver’s and power circuits (by an opto-member), the illumination can be powered both from a common source or from an independent accumulator. The NF-3RC unit can be used also as a basis for your own constructions for excitation of MOSFET power transistors.

The circuit is extended with detection of failure of the receiver's signal - it is indicated by permanent flashing of the anti-collision flash lights and the landing lights.

The NF-3RC, besides control circuit, includes 1x5 mm 20 mAh green LED, 2x5 mm 20 mAh red LEDs and 6x5 mm 20 mAh white LEDs


temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
NF-1 RC set
NF-1 RC set

temporarily out of stock
temporarily out of stock

Connectors MPX male
Connectors MPX male

temporarily out of stock
temporarily out of stock

Connectors MPX female
Connectors MPX female

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Ball link Aluminio M3 (2 pcs)
1 x Conector XT-30 (hembra)
1 x Aluminium red ball links M3 V1 (10 pcs)
1 x Black large kwik link (10 pcs)
1 x Blind nut M6 (4 pcs)
1 x Aluminium cap bolt washer M4 red (8 pcs)
1 x Civilian pilot "Pamela" size 9cm (Slimline)
1 x Spinner NUT M6
1 x Conector MT-60 (pair)
1 x Ball Link ALU M3 - RH (1 pcs)
1 x BRASS CONTROL HORN M3x16 mm 2pcs
1 x Piloto Jet "Red" 1/6 Scale
1 x Aluminium wide washer M4 Blue (4 pcs)
1 x Banna gold connector 2,5 mm (100 M/F pairs)
1 x Conector JR/Uni Servo female BLUE silicon (10 pcs)
1 x Conector JR Servo male (10 pcs)
1 x Spinner fixed propeller 42 mm / 5,0 mm
1 x Conector JR/Uni Servo male BLUE silicon (10 pcs)
1 x 30 cm DEANS female connector
1 x 1/6 Pilot "Cindy"
1 x Bag connector 2 mm
2 x Couple M4 for wire (10 pcs)
1 x Spinner NUT M5
1 x 4 mm M3 red control terminal (4 pcs)
1 x Militarian pilot "Kamikaze" size 9cm (Slimline)
1 x Piloto RC Civil 1/5- 1/6 Scale 12"
1 x Anodized aluminium servo M4x5/8 screw (4 lilac pcs)
1 x Spinner NUT M4
1 x Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x Clevis plastico I=45 mm / hole 3mm / pin 1 (2 pcs)
1 x 2 mm male connector (2 pcs) with safety connector
1 x 1/10 Pilot "Jack"
1 x Kwik link AL M4 con Clip (2 pcs)
1 x Spinner Alumin. fixed propeller 40 mm / 3,2 mm
1 x Clevis plastico I=44 mm / hole 3mm / pin 2 (2 pcs)
1 x Pilot "Anthony" (Slimline)
1 x Aluminium cap bolt washer M4 blue (8 pcs)
1 x Anodized alum. M3x0,5x20 mm Flat Head screw (4 blue pcs)
1 x Civilian pilot "Gramps" size 9cm (Slimline)
1 x Conector XT-30 (macho)
1 x Pilot "Dick" Legends Series (Slimline)
1 x 1/12 Pilot "Langley"
1 x Aluminium wide washer M4 Gold (4 pcs)
1 x 1/6 Pilot "Garry"
1 x Cable coupler M3 (10 uds)
1 x Conector JR Servo female (50 pcs)
1 x Spinner fixed propeller 60 mm / 5,0 mm
1 x 1/6 Pilot "Tony"
1 x Crimping sleeves for 1.1 mm cable (10 pcs)
1 x Extension silicon 50 cm (Graupner)
1 x Fresa corte diamante Ø 1.4mm (bola)
1 x Beech dowels 4.0 x 1000 mm
1 x Extension 30 cm (Futaba)
1 x Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x Foreman, scale 1:32
1 x 40,0 mm hydro-propeller (left hydropropeller)
1 x Ferrita 27x14x7 mm
1 x 2,0x50 mm allen screwdriver
1 x Straightened rod Ø 0.8 mm x 1000 mm
1 x Brass rod Ø 1.5 mm x 1000 mm
1 x Hard brass tubing (L 1000 mm, Ø10.0 mm, Ø9.1 mm)
1 x Canopy Latch
1 x Straightened rod Ø 4.0 mm x 1000 mm
1 x 25 mm Sandpaper file
1 x 
1 x Copier 5x20 cm pcs
1 x Fabric scissors curved Premium, 16 cm / 6" length
1 x Universal Colour Paste white 50 g
1 x Cable S.BUS 3 salidas 100 mm
1 x Aluminum Bayonet / strongal D12 mm / 0.5 m
1 x Ferrita con funda
1 x Foam plastic plates (310x210x5 mm)
1 x Straightened rod Ø 2.5 mm x 1000 mm
1 x Extension PVC 150 cm (Graupner)
1 x Brass rod Ø 0.8 mm x 1000 mm
1 x Cable silicona female batt. receptor 30 cm (Futaba)
1 x Carbon plate 350x150x1.0 mm
1 x LA500 pilot-seat set
1 x Cierva C30 Body Spain
1 x Head runner
1 x LA500 cyclic central part
1 x Cierva C30 spanish decoration Stickers
1 x Nut M2
1 x Head spacer
1 x LA500 pre-rotation gear hub
1 x Exhaust elbow for SAITO FA65/72/80/82a/91S/100/
1 x LA500 ciclic lever
1 x Motor rotor LA-500
1 x Junta humo metalica G55 (DLE55/DLE111/DLE222)
1 x Rotorshape Autogyro
1 x Steering lever
1 x Ball joint long
1 x LA500 nose
1 x Cierva C30 simulated motor
1 x Servo Arm 25T M3 KAVAN 6.5 / 19.6 mm
1 x Fully Threaded Steel Rod M2,5 (2 uds)
1 x Threaded coupler M2 (10 uds)
1 x Spinner 140 mm GFK
1 x Threaded coupler ALU M2 Ø 4 (2 uds)
1,575.08EUR
Manufacturers
Manufacturer Info
Night Fly
Night Fly Homepage
Other products
Languages
Español English
Currencies