Top » Catalog » Hardware » Adhesives/Resin/Epoxy » Resin/Gelcoat » R11212505

17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
    Cianocrylate->
    Epoxy->
    Resin/Gelcoat
    Glass Bubbles
    Contact adhesive
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

Turbina XICOY X240 compact
3,385.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

3 x	Gates hinge 30x16 mm (2 pcs)
3 x	15 mm reinforced hinge
1 x	Unmounted aluminium pin 6x98 mm (2 pcs)
2 x	Nylon hinge for flaps 33x9 (2 pcs)
1 x	67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x	Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
2 x	Flap hinge (6 pcs)
1 x	Gates hinge aluminium (1 pcs)
1 x	48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
2 x	Long pinned hinge (12 uds)
2 x	Long pinned hinge (6 uds)
2 x	Fast'n EZ-CA-Hinge (12 uds)
2 x	Miniature brass strap hinge, 1 m
2 x	Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x	Pin type hinge Al 4,5x70 mm (2 pcs)
1 x	Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
2 x	Nylon hinge 20x20x0,3 (10 pcs)
1 x	Cylidric hinge 33 mm Ø 2 mm (5 pcs)
2 x	Pin type hinge Al 6x98 mm (2 pcs)
1 x	Small pinned hinge (12 uds)
2 x	Gates hinge black 30x16 mm (2 pcs)
2 x	Flap hinge 33x9 mm (6 pcs)
2 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	Digital Air Speed Sensor And Pitot Tube Set
1 x	Truck-trailer for gliders 720 x 239 mm
2 x	Field folding model stand SebArt
1 x	Truck-trailer for gliders 720 x 285 mm
1 x	Propeller balancer
1 x	Surface Indicator Gauge Small
2 x	WingFix ULTRA Black Edition
1 x	Angle measurer
1 x	Tube Pitot to PIXHAWK
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x	Oracover Orange 2 m
1 x	Extension silicon 100 cm (Graupner)
1 x	6 mm blue aluminium threaded horn with patella
1 x	Horn for flap control (1 pcs)
1 x	Ball link duraluminium M3 V1 (10 pcs)
2 x	Pin type hinge Al 3,0x50 mm demount (2 pcs)
2 x	Nylon hinge for flaps/gates 27x10,5 (2 pcs)
2 x	Nylon hinge 20x15x0,3 (10 pcs)
2 x	resin-hardener L-385 H-385 (625 g)
1 x	Motor OS 3820-1200 electric
1 x	resin-hardener package L-385 with hardener H-385 (3.5 Kg)
1 x	Gates hinge
2 x	Glass Bubbles (0.12g) 400 G (aproxx 3.3 l)
1 x	Pin hinge 34x16 mm (10 uds)
2 x	Glass Bubbles (0,12 g) 350 ml
2 x	Micro flex hinge (12 uds)
2 x	Hardener Aero EPH 161 (500 g)
1 x	UHU hart 35 g
1 x	UHU Por 50ml/40g
1 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Mudguard wheels 112/127 mm
1 x	Glider retract undercarriage 8-16 Kg 2.5-3.2(127 mm wheel)
1 x	VPP system propeller for AXI VPP motors (spare)
1 x	Glass fibre braided sleeve (45mm) roll 10m
1 x	Teflon rollers 40 mm x 15 mm Diam.
1 x	PVC grid straight 290x185x0.32 mm
1 x	Sandwich carbon + poplar 2mm + carbon 290x160 mm
1 x	PET film Mylar® A 350, 50 cm, roll/ 2 m
1 x	Glider retract undercarriage 8-16 Kg 2.5-3.2(140 mm wheel with b
1 x	Actuator Electric 25 mm
1 x	Blades 330mm
1 x	Retract undercarriage for gliders 3-7 Kg 3.8-4.3 (without wheel)
1 x	Propeller balancer
1 x	PIX Hawk with accesories
1 x	EasyFLY Addon
1 x	Ball link M2 (10 pcs)
2 x	Round flex hinge (12 uds)
1 x	Small flex hinge (12 uds)
1 x	Hardener P-25, canister 2.5Kg
1 x	resin-hardener package L-385 with hardener H-385 (875 g)
1 x	Epoxy Resin L 285 + Hardener 285 (Aero), kit/ 1 kg
1 x	MEKP Harderner 100 g
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	Short ball link M2 (6 uds)
1 x	M3 Maxi ball link (2 uds)
1 x	Pin hinge 39x20 mm (10 uds)
1 x	Socket head ball link M3 (2 uds)
1 x	Ball link M3 RPA's-UAV's
1 x	Large flex hinge (12 uds)
1 x	Short ball link M3 (6 uds)
1 x	Joint with bearing M2,5 22x5,5
1 x	ROBART POINT HINGE 4,7mm (5 pcs)
1 x	Long ball link M1.6 (6 uds)
1 x	Socket head ball link M3 (2 uds)
1 x	M2,5 Diam metal ball link V3 (2 pcs)
1 x	Ball link M3 (10 pcs, flat ball)
1 x	Socket head long ball link M3 (6 uds)
1 x	M2/M1/6 3Diam short black ball link V1 (6 pcs)
1 x	M3 Maxi ball link (2 uds)
1 x	Blue metalic ball link M3/3 azul (2 pcs)
1 x	M2,5 5Diam metal ball link V3 (2 pcs)
1 x	M2,5 / 5Diam metal short ball link V3 (2 pcs)
1 x	Joint with bearing M2 22x5,5
2 x	Small pinned hinge (6 uds)
1 x	M2 5Diam black ball link V2 (2 pcs)
1 x	M2/M1/6 3Diam long black ball link V1 (2 pcs)
1 x	M2/M1/6 3Diam short black ball link V1 (2 pcs)
1 x	Ball link M3 (6 uds)
1 x	Joint with bearing M3 22x5,5
1 x	M3 INDUSTRIAL ball link (2 uds)
1 x	Fast'n EZ-CA-Hinge, lite (12 uds)
1 x	M3 Maxi ball link (2 uds)
1 x	6 mm ball link M3 (10 pcs)
1 x	M2,5 Diam metal short ball link V3 (2 pcs)
1 x	Thixotropic agent TM 100, tin/ 75 g (approx. 1 l)
1 x	Cotton Flocks, bag/ 7 Kg
1 x	Colador RABBIT
1 x	Cotton Flocks, bag/ 500 g
1 x	Thixotropic agent tin/ 15 g (approx. 350ml)
1 x	Spark Ceramic JETCENTRAL
1 x	HDT Jet Central
1 x
1 x	Glass Bubbles 0.20 g/cm³ Panda, tin/ 100 g (approx. 1 l)
1 x	Thixotropic agent TM 100, tin/ 415 g (approx. 5 l)
1 x	Power Pack SE Series JETCENTRAL
1 x	GlassBubbles 2.5 g/cm³ Panda, tin (approx. 1 l)
1 x	White gelcoat 1 Kg
1 x	Pegamento Pu R 50g polyuretano
1 x	resin-hardener L-385 H-385 (5000 g)

3,773.48EUR