Top » Catalog » Hardware » Adhesives/Resin/Epoxy » Resin/Gelcoat » R1101201

39.25EUR

Hardener EPIKURE™ Curing Agent MGS™ LH285, bottle/ 800 g
[R1101201]

Hardener for Epoxy Resin L 285
Processing time: 50 minutes
Mixing ratio:
100 : 40 parts by weight of Epoxy Resin L 285 : Hardener 285
Curing time: 24 hours at room temperature, followed by hot curing for 15 hours at 55 °C
Please order Epoxy Resin L 285 separately
Laminate structures for vehicle construction in combination with this product and Epoxy Resin L 285 are approved by the TÜV-Süd.
Laminate structures for vehicle construction in combination with this product are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
For further technical data and detailed information on processing, please refer to the comprehensive PDF "Technical Information on System L 285" (to be found in the appendix under "Article Information").
Former brand names: Hexion®, Bakelite®

under request

Reviews

1 x	Piston pin for DA-60 DA-120
1 x	Motor DA 100L
1 x	Ignition for DA-50-R, DA-60, DA-85
1 x	Piston pin for DA50R/DA100
2 x	Gasket carburetor carrier->crankcase DA-85 DA-100L DA-120 DA-200
1 x	Pitts Muffler for D.A. 100
1 x	Carburetorgasket DA-85, DA-100, DA-100L and DA-120
1 x	Low speed needle DA-50R/100I
1 x	Hifht speed needle DA-50R/100I
1 x	Reed valve cage with petals for DA 100/150
1 x	Motor DA 150
1 x	Crankcase Gasket set for DA-60 / DA-120
1 x	Piston ring for DA-85 and DA-170
1 x	Ignition unit for DA-70/100/120/150/170/200
1 x	Cylinder for DA-85/170 (1 piece)
2 x	Carburetor for DA150L/170
1 x	Gasket, from reed valve carrier to carb carrier DA-150L/170
1 x	Gasket, from red carb carrier to crankcase DA-150L/170
1 x	Reed valves, set DA-100/150/150L/170
1 x	Crankcase gasket DA 170
2 x	Reed valve carrier, without reed valves DA-150L/170
1 x	Gasket, Aluminium-Plate >reed valve carrier DA-170
1 x	Motor DA 120
2 x	Carb Carrier, red DA-150L/170
1 x	Stainless steel silencer for DA 150/150L
1 x	Hifht speed needle DA-50R/100I
1 x	Exhaust gasket DA50R DA100 DA200
1 x	Cer clip DA-50R, DA-60 DA-100 DA-100L DA-120, 1 piece
1 x	2000A 12V Lithium Jump Starter with 150PSI Air inflator
1 x	Hifht speed needle DA-60
1 x	Prop washer for DA-85, DA-100, DA-100L, DA-120
1 x	Cylinder DA-50R, DA-100, DA-100L
1 x	Gasket, Carburetor DA-150/170
1 x	Carburetor diaphragm set DA-150/170
1 x	Simulador RealFlight RF-9.5 S (sin emisora)
1 x	Stainless steel silencer for DA 150/150L
1 x	Propeller 10x4,7 SlowFlyer
1 x	6 mm hexagonal ball link M3 (10 pcs)
1 x	Horn for flap control (1 pcs)
1 x	Threaded coupler ALU M2,5 Ø 6 (2 uds)
1 x	1000 ml sealer (DOPE)
1 x	Horn with ball 40x30
1 x	Presto SF Light Filler styrene-free (420 g)
1 x	Spray adhesive INFUTAC (Clear) 500 ml
1 x	Joint with bearing M2,5 22x5,5
1 x	Threaded coupler ALU Left M2,5 Ø 3 (2 uds)
1 x	Propeller electric carbon 9.5x7
1 x	Propeller POWER-PROP 11x9
1 x	Clevis plastico I=26 mm / hole 2mm / pin 1 (2 pcs)
1 x	Clevis plastico I=44 mm / hole 3mm / pin 2 (2 pcs)
1 x	Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x	800TVL CMOS camera for FPV
1 x	Xplorer4 anemometro
1 x	Cable coupler M2 (10 uds)
1 x	Xplorer2 anemometro
1 x	Strip 2,5x1,25x330 mm
1 x	ABS Strip 1.0x3.0x1000 mm
1 x	Round Rod 1,0x1000 mm
1 x	Anodized alum. M4x0,7x20 mm Flat Head screw (4 blue pcs)
1 x	Carbon fiber rod 10 mm x 1000 mm
1 x	Carbon fiber flat 1000x3.0x1.0 mm
1 x	Round Rod 1,25x1000 mm
1 x	Carbon fiber rod 6.0 mmx1000 mm
1 x	Surface Indicator Gauge Small
1 x	Anodized aluminium servo M3x16 screw (4 red pcs)
1 x	Blind nut M6 (4 pcs)
1 x	ABS tube 6.0x4.0x1000 mm
1 x	ABS tube 5.0x4.0x156 mm
1 x	ABS tube 8.0x7.0x1000 mm
1 x	Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm)
1 x	Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x	Tape GFK 25 mm
1 x	Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
1 x	ABS tube 18.0x16.0x1000 mm

7,246.04EUR

39.25EUR

Hardener EPIKURE™ Curing Agent MGS™ LH285, bottle/ 800 g[R1101201]

under request

Hardener EPIKURE™ Curing Agent MGS™ LH285, bottle/ 800 g
[R1101201]