54.24EUR

NF-3 RC set
[NF-3RC Set]



Funcionamiento del NF-3

Esquema de conexi�n
NF-3RC extends the capabilities of the NF-2RC unit with a greater number of circuits and more flash lights regimes. Just as NF-2RC it has two position lights circuits. It has also two landing lights circuits and two flash light circuits. Switching on/off of the second landing lights circuit is delayed by 1 second against he first circuit. That produces an effect of phased switching by the pilot. Eight different combinations of flashing can be selected for the two flash light circuits. Three couplers (jumpers) are used for selection.

One second is split into 16 parts. It is possible to set during which parts the light should be on (1) and off (0) to both flash circuits. Such a couple of sequences of 16 ones and zeros represents one combination of flashes. Eight such combinations (couples of sequences) are saved in the unit. By default, the unit contains six combinations of 1, 2 and three mutually shifted flashes plus two flashing modes 1:1, one with the period 1s, the other twice faster. The last two regimes are designed especially for helicopters owners.

A coupler is used for selection of 2- and 3-positional control regime as in NF-2RC. If the 2-position control is selected, in the first position the position and ant-collision lights light, in the second position the landing lights get switched on, too. In the three-position regime, in the first position, all lights are off, in the second position the position lights and anti-collision flash lights are on and in the third position, all lights are on. The unit can be used also in no-control mode. In that mode, position and flash lights are permanently turned on and the coupler for regime selection switches the landing lights.

Thanks to a galvanic separation of the receiver’s and power circuits (by an opto-member), the illumination can be powered both from a common source or from an independent accumulator. The NF-3RC unit can be used also as a basis for your own constructions for excitation of MOSFET power transistors.

The circuit is extended with detection of failure of the receiver's signal - it is indicated by permanent flashing of the anti-collision flash lights and the landing lights.

The NF-3RC, besides control circuit, includes 1x5 mm 20 mAh green LED, 2x5 mm 20 mAh red LEDs and 6x5 mm 20 mAh white LEDs


temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
NF-1 RC set
NF-1 RC set

temporarily out of stock
temporarily out of stock

Connectors MPX female
Connectors MPX female

temporarily out of stock
temporarily out of stock

Connectors MPX male
Connectors MPX male

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x 30 cm DEANS female connector
1 x PowerBox Evo
1 x Gold antispark 5,5 mm plug
1 x Conector BEC female (10 pcs)
1 x Extension for SensorSwitch 30cm
1 x PowerBox MagSensor black connector SRS/Champion
1 x Connectors banna gold 5,5 mm (M/F)
1 x PowerBox Champion SRS
1 x Connectors banna oro 6,0 mm (M/F)
1 x EC5-Set female, simple quality, 2 x female pin, 1 x blue housing
1 x XH female balance (4S) connector (2 pcs)
1 x Connectors banna oro 8,0 mm 5 pcs(Female)
1 x MicroMatch PowerBox
1 x Connectors banana oro 6,0 mm Ultralight (M/F)
1 x XH male balance (2S) connector (2 pcs)
1 x Hot Glue Stick RED
1 x Starter Sullivan-STAR 603 DINATRON
1 x Digital precision scale up to 2000 g
1 x 3,0x60 mm allen screwdriver
1 x Starter EM Gear Power 250
1 x Starter Sullivan-STAR 601
1 x Screwdriver for Hexagon 1,27mm
1 x Disposable Injector Bags (30x16cm) 100 pcs
1 x Z Bender - S Type Tool
1 x Ball Link Plier
1 x PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x Screwdriver for Torx® TX8
1 x Starter EM Gear Power 80
1 x 
1 x Vacuum pump 12 CFM
1 x PROXXON - SANDING BELTS FOR BSL 220/E 80 GRIT (5 pcs)
1 x Starter 12v (Max 90 and 15ccm)
1 x Crimping tool
1 x Vacuum pump P1-N
1 x 2,5x60 mm allen screwdriver
1 x Z Bender - S Type Tool
1 x PROXXON - SANDING BELTS FOR BSL 220/E 180 GRIT (5 pcs)
1 x Starter 12v (Max 180 and 30ccm)
1 x Cut tube
1 x Hexagonal ball head 2.0 x 50 mm
1 x Crimping tool
1 x Tube Pitot to PIXHAWK
1 x PPM Encoder Module
1 x PIX Hawk with accesories
1 x Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x CC 03
1 x Bec MR UBEC 5A (5v/6v/7v)
1 x 4 LiPo XH>EH adapter
2 x APM2.6 Power module with 5.3V DC BEC
1 x Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x TP/TopFuel - JST-EH 4/5S Adapter
1 x "Y" charging 4mm wire (2 IN-1 OUT).
2 x 3 LiPo XH>EH adapter
1 x Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x 2 LiPo XH>EH adapter
1 x CM-3
1 x 5 LiPo XH>EH adapter
1 x 30 cm BEC cable (female)
1 x Dean "T" - Futaba Adapter
1 x Brass control horn M4 short for wire (10pcs)
1 x Pilot "Anthony" (Slimline)
1 x Threaded coupler ALU M3 Ø 6 (2 uds)
1 x Green smoke canister 65 g
1 x Straightened rod Ø 7.0 mm x 1000 mm
1 x 6 mm Quick clamp_S (10 pcs)
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x Tapa estado carga XT-60 (6 pcs)
1 x Support Flush MPX Conector (6 pcs)
1 x Support FUEL DOT V3
1 x Aro pasacable Ø20 mm (4 pcs)
1 x Black copper lacquer wire Ø0,2 mm (5 m)
1 x Tool for entel
1 x Copier 5x20 cm pcs
1 x Pistola termica MH 550 micro
1 x Fabric scissors curved (offset handles), 16 cm / 6" length
1 x Digital weight, angle and balance meter BASIC
1 x Set brocas Ø 0.4-0.6-0.8-1.0 mm (4 pcs)
1 x Roller cutter 28 mm
1 x 25 mm Sandpaper file
1 x Propeller drill jig DA 100/85/120/150/200 and VM 60-210
1 x Set brocas Ø 1.2-1.4-1.6-1.8 mm (4 pcs)
1 x Vacuum Connection VA 1 (for hose Ø 6 mm)
1 x Motor mount EDGE 540 48"
1 x DPSI RV Mini 6 (2008)
4,426.22EUR
Manufacturers
Manufacturer Info
Night Fly
Night Fly Homepage
Other products
Languages
Español English
Currencies