133.31EUR

NF-3XL set
[NF-3XLSet]


NF-3XL is a unit designed for illumination of models with spread up to l.7 metres for flying at night. lt is used to power colour ultra bright LEDs (Light-Emitting Diode) It contains six independent current-powered outputs. Five outputs are powered with the nominal current of 20 mA. Two outputs are for position lights (P1, P2), two independently flashing ones for the anti—collision flash lights (F1, F2), and one output for the landing lights (L1). The sixth output (L2) is designed to power the landing headlight of 80, 150 or 350 mA (according to the respective type). Operation of the output L2 is one second delayed to the output L1. That produces an effect of phased switching by the pilot.

The unit offers eight different flashing combinations ( 0 -7 ) with one second period for F1 and F2 outputs. One of those combinations can be selected by couplers (jumpers) 1, 2, 4. The sum of numbers ofthe connected couplers represents the number of the selected combination. The unit can be used as controlled or non-controlled by pilot. lf controlled by pilot, the jumper "3p" allows you to select between 2-positions (Fly/Landing) or 3—positions (Off/Fly/Landing) control by the remote controller. With a 2-positions control the position and anti-collision lights start work when the unit is connected to the accumulator. However, the landing lights can be switched on and off by pilot. ln the 3-positions control system, all lights are off in the off-position. ln the fly-position the position and anti-collision lights are on and in the landing-position, all lights are on.
Unit is in non-controlled mode if the Rx cable is not connected to the receiver. ln this case the lights start work when the unit is connected to the accumulator and the "3p" jumper can be used to switch manually the landing lights off. Anti-collision and landing lights automatically begin to flash when the plane is unable to receive a signal from the remote controller. The receiver circuit and the light circuits are electrically separated by an opto-coupler. Unit is compatible with Graupner or Hitec type connectors.
The outputs maintain the nominal current in the wide range of voltage from 6V to 14V without the need to connect compensating resistance series in the circuit. The stabilization starts working from 4.5V, therefore it is possible to connect the unit with the used NiCd or NiMH batteries with 5 up to l0 cells or Li-Pol from 2 up to 3 cells. As the number ofthe cells of the powering accumulator increases, so does the number of diodes that can be connected (serially) in one circuit.

The NF-1RC, besides control circuit, includes 1x10 mm 150 mAh green LED, 2x10 mm 150 mAh red LEDs, 6x10 mm 150 mAh white LEDs, 2x5 mm 20 mAh white LEDs and 1x reflector with a 25 mm 350 mAh LED suitable for landing gear.


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x CC 02
1 x Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
1 x Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x Cabel charger transmitter GRAUPNER
1 x 5 LiPo XH>EH adapter
1 x Black copper lacquer wire Ø0,2 mm (5 m)
1 x BEC 3A FOXY
2 x DPS Switch JR/JR
1 x CC 03
1 x CC 01
1 x 2 LiPo XH>EH adapter
1 x CM-3
1 x Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x Circlick securite
1 x UBEC 6A KAVAN
2 x Connector Sub-D 2+5 Female
1 x CellPRO 4S Adaptader (GP/KO up to 4S)
1 x 30 cm BEC cable (male)
1 x Dean "T" - Futaba Adapter
1 x "Y" charging 4mm wire (2 IN-1 OUT).
1 x Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x Cabling for Fox MDM1 wings
1 x EWC3 100 cm wing connector
1 x Connector CAN 15
1 x Male connector for 6 pines AWG
1 x Female connector for 12 pines AWG
1 x wing/fuselage connector for 12 pines AWG 20-24
1 x Three-position switched channel, short
1 x Double conector with JR adapter and 200 mm extension
1 x SPARK Switch 7.4v
1 x wing/fuselage connector for 3 pines AWG 20-24
1 x DPSI Ampere battery backer
1 x Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
1 x Male connector for 16 pines AWG
1 x PWC4 wing/fuselage connector for 4 servos
1 x Male connector for 12 pines AWG
1 x SPARK Switch 12v
1 x PWC6 PowerWingConnector for 6 servos with fuselage socket
1 x Female connector JST SH 1.0mm with 10 cm wire
1 x FX three-position switched channel, long
1 x Female connector for 10 pines AWG
1 x Extractor piñones 2.3/3.2 mm
1 x JETImodel Addcap 1640
1 x Female connector for 16 pines AWG
1 x Short Switch On/Off micro
1 x Male connector for 20 pines AWG
1 x Connector Sub-D 2+5 Male
1 x wing/fuselage connector for 6 pines AWG 20-24 (without pines)
971.61EUR
Manufacturers
Manufacturer Info
Night Fly
Night Fly Homepage
Other products
Languages
Español English
Currencies