Top » Catalog » Hardware » BEC/Cables/Conectors/Interruptor » EMCA15020

119.90EUR

DPSI Ampere battery backer
[EMCA15020]

Powerful battery backer with peak current capacity of up to 60 ampere. The DPSI Ampere can be used as dual power supply for receivers, turbines or similar electric consumers of R/C models. System stability of the DPSI Ampere is ensured by connecting two batteries. If one battery fails, safe operation is guaranteed by the second battery. Normally, both batteries are discharged symmetrically and simultaneously (at the same time). Due to the parallel connected batteries the current is split in half for each battery. The DPSI Ampere is switched ON/OFF electronically by placing a magnet on the corresponding position on the device housing.

The DPSI Ampere can handle a permanent current of 50 ampere. So it is the perfect solution for all high current applications. Thanks to an integrated charging connector both connected batteries can be charged simultanously with only one charging device.

The DPSI Ampere is the first EMCOTEC battery backer that can be operated with 3S LiPo batteries or batteries with voltages up to 13.2 volts. So the module is much more than a conventional dual power supply for receivers. Due to the higher voltage also devices such as turbines can be reliably powered with the DPSI Ampere.

Delivery includes switching magnet with EMCOTEC patch, backup magnet, 3D sticker as well as German and English operating instructions.

Specifications
Current sources: 4S to 8S NiCd / NiMH batteries, 2S to 3S Lithium++ batteries (LiPo, LiFePO4, LiIon)
Operating voltage range: 2.6V (*) .... 13.2V
Nominal input voltage: 3.6V .... 13.0V
Output voltage: same as input voltage (no dropout losses)
Quiescent current (turned off): < 4µA per battery
Quiescent current (turned on): approx. 30mA total
Max. continuous current: 50A (30A per channel)
Max. peak current (10 sec.): 60A (30A per channel)
Internal resistance: approx. 3mR
CE test: according to 2004/108/EG
Environmental conditions: -10°C .... +50°C (14°F ... 122°F)
Permissible temperature range: -25°C .... +70°C (-13°F ... 158°F)
Dimensions (L x W x H): 60mm x 64mm x 16mm (2.36in x 2.52in x 0.63in)
Weight: 45g (1.59oz)

temporarily out of stock

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

DC24 II Transmitter case insert
35.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

2 x	CC 02
3 x	CC 01
1 x	Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
1 x	BEC 3A FOXY
1 x	Black copper lacquer wire Ø0,2 mm (5 m)
1 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	UBEC 6A KAVAN
1 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
2 x	CC 03
2 x	Copper lacquer wire Ø0,2 mm (5 m)
2 x	Dean "T" - Futaba Adapter
1 x	Connector Sub-D 2+5 Female
2 x	Cabling for Fox MDM1 wings
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
2 x	CM-3
1 x	CellPRO 4S Adaptader (GP/KO up to 4S)
2 x	30 cm BEC cable (male)
2 x	3 copper lacquer wire Ø0,2 mm (1 m)
2 x	Connector CAN 15
1 x	Connector Sub-D 2+5 Male
2 x	Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
2 x	5 LiPo XH>EH adapter
1 x	Cabel charger transmitter GRAUPNER
1 x	Canopy Latch
1 x	Crimping sleeves for cable 1.3 mm (10 pcs)
1 x	Steering arm 16 mm Ø 3 mm (2 uds)
1 x	Steering arm 12 mm Ø 3 mm (2 uds)
1 x	Canopy Lock V1 M3 Red (2 pcs)
1 x	Steering arm 16 mm Ø 4 mm
2 x	Aluminium alloy coupler for carbon tube 6/M4
1 x	Locking cable tie 3.2x142 (uds)
1 x	Stainless steel cable Ø 0.62 mm (10 m)
2 x	Covered closure or fairings
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	Cap closure 33/23.5mm (2 uds)
1 x	Horizontal cockpit anchor "tipe F3A" (2 pcs)
1 x	Steering arm 16 mm Ø 3 mm
1 x	Stainless steel cable Ø 0.5 mm (2 m)
1 x	Steering arm 12 mm Ø 4 mm (2 uds)
1 x	Crimping sleeves for cable 0.85 mm (10 pcs)
2 x	Electric spoiler 250 mm (2 pcs)
1 x	Cierre cabina aluminio Ø5, I=16 mm
1 x	Stainless steel cable Ø 1.3 mm (10 m)
1 x	Steering arm 12 mm Ø 4 mm
1 x	Micro screw-lock pushrod conn snap Ø 1 mm (2 uds)
1 x	Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x	SUS wire 3m (nylon coated)
1 x	Locking cable tie 2.5x100 (uds)
1 x	Hard aluminium thin-walled tube with fibreglass case ø30x1mm, 1m
1 x	Aluminum Bayonet / strongal D12 mm / 0.5 m
1 x	Horn 6/35 with M3 Bearing
1 x	Horn 6/27 with M3 Bearing
1 x	6 mm blue aluminium threaded horn with patella
1 x	Threaded coupler ALU M3 Ø 6 (2 uds)
1 x	Horn 20x28,5 mm (2 pcs)
1 x	Threaded coupler ALU M2 Ø 4 (2 uds)
1 x	Small aluminium horn gold (2pcs)
1 x	Threaded coupler ALU Left M3 Ø 4 (2 uds)
1 x	Cable with accesories
1 x	LH long aluminium horn L31xH30 (2pcs)
1 x	6 mm aluminium horn with patella
1 x	Horn 5/20 with M2 Bearing
1 x	LH long black aluminium horn L31xH30 (2pcs)
1 x	Horn 5/15 with M2 Bearing
1 x	Horn 5/10 with M2 Bearing
1 x	Threaded coupler ALU Left M2,5 Ø 4 (2 uds)
1 x	Horn 16,5x20 mm (2 pcs)
1 x	Horn with ball 40x30
1 x	Brass control horn M4 short for wire (4 pcs)
1 x	Brass control horn M2 short for wire (2 pcs)
1 x	Threaded coupler ALU M3 Ø 4 (2 uds)
1 x	Threaded coupler ALU M2,5 Ø 4 (2 uds)
1 x	Brass control horn M4 short for wire (10pcs)
1 x	RH long aluminium horn (2pcs)
1 x	SlowFlyer control horn (3 pcs)
1 x	Threaded coupler ALU M2,5 Ø 3 (2 uds)
2 x	Horn 13,5x16 mm (2 pcs)
1 x	30 cm BEC cable (female)
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	Double conector with JR adapter and 200 mm extension
1 x	Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
1 x	3 LiPo XH>EH adapter
3 x	CC 05
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	Adapter lead MPX/EC3
1 x	DPSI Ampere battery backer
1 x	Blue metalic ball link M2/2 azul (2 pcs)
1 x	Profile ABS triangular 4.0x1000 mm 90º
1 x	Profile ABS Square 4 x 1000 mm
1 x	Plasti Dip Liquid Tape 429 ml black
1 x	Brass ball links BS M3 V1 (10 pcs)
1 x	Interface Realflight Simulator
1 x	AX-60 starters (5 pcs)
1 x	Glases Nimbus
1 x	A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x	Balsa panel 5.0x100x1000 mm
1 x	Aro pasacable Ø20 mm (4 pcs)
1 x	Aluminun wheel collar 5 mm Ø (4 uds)
1 x	140 mm rods set for direction control
1 x	45 mm rods + T patellas set for direction control
1 x	38x4,5 mm wires output (2 pcs)
1 x	Tip wing protector 40x14 (2 pcs)
1 x	Split M1,2x10 (10 pcs)
1 x	Allen wheel collar M3x3
1 x	Steering arm 16 mm Ø 4 mm (2 uds)
1 x	Wing bolts M3 Steel screw blue (2 pcs)
1 x	Wheel collar 3.5 mm Ø (4 uds)
1 x	165 mm PVC transparent battery termo-retract 165 mm (10 m)
1 x	4,8x1000 mm 2:1 red termoretract tube
1 x	Screw-lock pushrod conn snap Ø 1.5 mm (2 uds)
1 x	SBEC 40
1 x	20 mm carbon horn
1 x	USB interface ALTIS
1 x	1,2x1000 mm 2:1 black termoretract tube
1 x	Electric spoiler 300 mm (2 pcs)
1 x	13 mm wing servo holder
1 x	LiPo Storage Box Type "P"
1 x	Avia spare fouselage CF reinforced (Top Model)
1 x	Foil for sticking flaps and ailerons
1 x	ARTIST 1.560 mm
1 x	18 mm wing servo holder
1 x	Albatros ,spare cockpit (Top Model)
1 x	Battery bed V2_S (black)
1 x	Bidule 111 3000 mm
1 x	Spring clamp for tube Ø29 mm ext 1pc
1 x	Stainless steel cable Ø 0.5 mm (20 m)
1 x	Canopy Astra
1 x	Astra (Top Model)
1 x	LiPo Storage Box Standard 1 Type 1
1 x	Sanyo RX Battery Eneloop 4,0 V AAA JR
1 x	Bidule 55 V3 2460 mm
1 x	PVC 0,14 qmm servos wire JR/Graupner (5 m)
1 x	RX Battery Eneloop 4,8 V JR 2500 mAh
1 x	Sanyo RX Battery Eneloop 4,8 V JR
1 x	Sanyo TX Battery Eneloop 7,2 V MPX
1 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Cockpit metalic closing
1 x	L cockpit anchor "tipe F3A" (2 pcs)
1 x	Mudguard for 140/165 mm wheels
1 x	Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x	Wheel collar 2 mm Ø (4 uds)
1 x	Aluminum Bayonet / strongal D25 mm / 1 m
1 x	Wing-connector: Glass / Carbon tube (26.5/25 x 25/23) x 1000 mm
1 x	Extra long horn 60x30
1 x	Long adjustable control horn 3x34
1 x	5 mm M2 variable horn
1 x	Horn mando small (2 pcs)
1 x	Duralumium F3A horn 30x10x23,5 mm (2 pcs)
1 x	Horn DUBRO 1/2A
1 x	Pins M connect Multipin connectors AWG 20-24
1 x	Horn DU-BRO 1/2 (2 pcs)
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	SPARK Switch 12v
1 x	wing/fuselage connector for 6 pines AWG 20-24 (without pines)
1 x	PWC4 wing/fuselage connector for 4 servos

4,708.66EUR