21.00EUR

Partall paste 650 g
[R1651601]


Characteristics:
- For Epoxy-, polyester- und vinylester resins.
- Silicone-free.
- Useable up to 60 °C.

A blend of hydrocarbon and microcrystalline waxes. For high-gloss surfaces. Ideal for smooth and sealed surfaces e.g. on GRP moulds.

Polishing possible after a drying time of approx. 1-2 minutes.

Could be used in conjunction with film release agent PVA.

Available in green and colourless.

It is particularly recommended for use on moulds where standard silicone waxes hinder post-finishing operations or as a primer coat prior to the application of PARTALL® Coverall Film. PARTALL® Paste #2 may also be employed as an economical edge wax on larger molds, and is used to seal rough wood moulds or plugs for casting composites, cements and grouts.

The maximum processing temperature is 60 °C.

Mould surface preparation
Before application of PARTALL® Paste #2 porous molds (i.e., plaster or wood) should first be cleaned and sealed. Composites grade sealers and fairing compounds (body filler) are recommended but a good surface on plaster or wood may be obtained with automobile type primer-sealers and lacquers. For non-cosmetic parts with rough wood molds or plugs a number of coats of PARTALL® Paste #2 should adequately seal the surface.

Application
Using a clean and dry cotton cloth, apply a small amount of Partall® Paste #2 to mould surface in a thin even coat. 0.5 - 1.0 g is enough for about one square yard (1m²). Turn over cloth and begin buffing immediately by hand (within one minute after application). On larger moulds or plugs work on smaller sections at a time or have second operator follow to polish. Power buffer equipped with a terry cloth or lamb’s wool pad will reduce labor time on larger moulds. Surface should be buffed to a glossy finish. Complete surface coverage is more important than a thick film of wax. In order to ensure complete coverage, repeat application and polishing process at least 3 times for initializing new or reconditioned moulds or plugs. Alternate direction of application of each coatimportant (i.e., 0°, 90°, circular, etc.). Polish each coat before applying the next.


temporarily out of stock
temporarily out of stock

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
3 x ABS "T" angle 4.0x4.0x1000 mm
1 x Rubber profile 10-2 mm 2M
2 x ABS angle 1.5x1.5x1000 mm
1 x ABS angle 2,0x2,0x1000 mm
3 x ABS angle 4,0x4,0x1000 mm
2 x Profile ABS Square 4 x 1000 mm
1 x Streamline Stainless Steel Tubing 10.5x5.7x1000 m
1 x ABS rectangular profile 10x5.0x1000 mm
1 x Profile ABS half cane 4x2.5x1000 mm
2 x Profile ABS half cane 2.5x1000 mm
2 x L-Connector 1.0 mm x 1000 mm
1 x Profile ABS Square 3 x 1000 mm
2 x Profile ABS half cane 4x1000 mm
1 x Profile ABS triangular 6.0x1000 mm 90º
1 x L-Connector 4.0 mm x 1000 mm
2 x Flat Connector 4.0 mm x 1000 mm
2 x Profile ABS triangular 2.0x1000 mm 90º
2 x Profile ABS half cane 7.0x1000 mm
1 x ABS "T" angle 10.0x10.0x1000 mm
1 x Profile ABS half cane 2.0x1000 mm
1 x Profile ABS Square 2 x 1000 mm
4 x Profile ABS half cane 5.0x1000 mm
2 x Profile ABS half cane 3x1000 mm
2 x L-Connector 1.5 mm x 1000 mm
1 x Profile ABS Square 1 x 1000 mm
1 x U Profile ABS 2,0x4,0x1000 mm
1 x ABS "T" angle 8.0x8.0x1000 mm
3 x U Profile ABS 5,0x10,0x1000 mm
1 x ABS angle 10,0x10,0x1000 mm
1 x ABS "T" angle 2.0x2.0x1000 mm
1 x Profile ABS half cane 6.0x1000 mm
1 x Profile ABS half cane 8.0x1000 mm
1 x U Profile ABS 8,0x4,0x1000 mm
3 x ABS "T" angle 6.0x6.0x1000 mm
1 x Oracover Brown 2 m
1 x Ply-Span 450x600/13g Blue
1 x Oratex White 2m
1 x Monokote BLUE metalizado (1.8x0.65m)
1 x Oracover Azul Cielo 2 m
1 x Oracover CARBON Metalic 1 m
2 x Oratex Yellow Cub 10 m
2 x Oracover Yellow CUB 10 m
1 x Xplorer3 anemometro
1 x Xplorer2 anemometro
1 x Xplorer1 anemometro
1 x Silicone adhesive ELASTOSIL® E4, tube/ 90 ml
1 x Partall paste 650 g
1 x Spray YELLOW Inca Lexan 150ml
1 x Streamline Stainless Steel Tubing 6.3x3.5x1000 mm
1 x Parachute expulsion foam
1 x Silicone 0,50 qmm servos wire Graupner(5 m)
1 x Cable tie mounts 4.3 (4 uds)
2 x Cross Connector 4.0 mm x 1000 mm
2 x Profile ABS triangular 4.0x1000 mm 90º
1 x Support Pitot JETI
1 x Recessed MPX connector support (6 pcs)
1 x Tube support Ø 6mm (10 pcs)
1 x ABS tube 20.0x18.0x1000 mm
1 x ABS rectangular profile 12x6.0x1000 mm
1 x PVC blue transparent battery termo-retract 68 mm (10 m)
1 x Streamline Stainless Steel Tubing 19.5x9.8x1000 mm
1 x Oracover Yellow CUB 2 m
1 x Oracover Yellow CADMIO 10 m
1 x Oratex Antik 2m
1 x PVC transparent battery termo-retract 195 mm (1 m)
1 x Streamline Stainless Steel Tubing 12.3x7.7x1000 mm
1 x Streamline Stainless Steel Tubing 7.5x4.5x1000 mm
1 x Streamline Stainless Steel Tubing 11.5x6.5x1000 m
1 x Ply-Span 450x600/13g Black
1 x PVC termo-retract battery 45 mm transparent orange (1 m)
1 x Oratex Red Fokker 10 m
1 x PVC yellow transparent battery termo-retract 69 mm (10 m)
1 x Streamline Stainless Steel Tubing 17.8x12.4x1000 mm
1 x PVC yellow battery termo-retract 69 mm (10 m)
1 x BALSA trip 3.0x3.0x1000 mm
1 x A/C quality beech plywood 498x247x2.0 mm
1 x Balsa panel 10x100x1000 mm
1 x A/C quality beech plywood 600x300x8.0 mm
1 x BALSA trip 2.0x10.0x1000 mm
1 x Balsa panel 2.5x100x1000 mm
1 x A/C quality beech plywood 600x300x0.8 mm
1 x ALBATROS 3.0 m (orange/white)
1 x Albatros ,spare cockpit (Top Model)
1 x Aero-Master Wings (Aero-naut)
1 x FOX 3000 mm ARF (FMS)
1 x Flip ARF (Top Model)
1 x Ion Pro NG electric with flaps GREEN Fluor (JP Model)
1 x FANTASY ARF 3.0m, Fundas alas
1 x Balsa panel 2.0x100x1000 mm
1 x Balsa panel 1.0x100x1000 mm
1 x A/C quality beech plywood 600x300x6.0 mm
1 x Ventus 1:4 set of instruments
3,863.35EUR
Manufacturers
Manufacturer Info
Roi-Import
Roi-Import Homepage
Other products
Languages
Español English
Currencies