59.00EUR 19.90EUR

Servo Controller Fibra optica


Servo controller based on fibre-optic transmission, allows to place e.g. throttle servo right next to the ignition without anxiety about disruptions “transfer” to the RC receiver.

Fibre-optic servo controller was designed as complement to the fibre-optic ignition cutoff. However, nothing stands on the way to exploit it independently.

The main task of controller is a possibility to place throttle servo close to the engine, so the throttle control link is short. Typically disadvantage of such installation is small servo distance and its wires from the engine ignition unit. Taking into account the adverse impact of electromagnetic noise caused by the ignition, which could get to the RC circuit, controller communicates with the receiver exclusively by fibre-optic which is resistant to electromagnetic disruptions. Thanks to that there is a minimum 30 cm distance between the ignition and the RC circuit in the model. In this case throttle servo is powered by the same package as the ignition unit.

Fibre-optic servo controller can be used also for other purposes than controlling the throttle. It will work everywhere where long wires are adversely affecting the electronics operation. With its help it is possible to control the servo move being in a significant distance or everywhere where a galvanic isolation of implementation servo elements from steering electronics is required.

FORCE Servo controller correctly works with voltage range from 3.6 V on the RC receiver side, and 3.6 V on the servo power supply side. Maximum allowed supply voltage on both sides is 16.0 V. It is necessary to remember not to exceed the allowed servo voltage, and if necessary to use appropriate voltage regulator.

FORCE Servo controller consists of the fibre-optic transmitter module plugged in the RC receiver and powered directly from it. Fibre-optic receiver module powered from the ignition battery. Fibre-optic wire*. For correct operation the device requires separate channel from the receiver (in most cases CH3).

Technical data:
Fiber Optic transmitter
– dimensions: 35mm x 11mm x 13mm
– receiver plug: Futaba, female 300mm
– power supply: 3,6V – 13,0V
* 2 – 3 x (LiPo/Li-Ion/LiFe)
* 4 – 9 x (NiMh/NiCd)
– weight: ~ 10,0 gram

Fiber Optic receiver
– dimensions: 47mm x 21mm x 13 mm
– battery plug: Futaba / JR male 150mm
– servo plug: Futaba / JR male 150mm
– power supply: 3,6V – 13,0V
* 2 – 3 x (LiPo/Li-Ion/LiFe)
* 4 – 9 x (NiMh/NiCd)
– weight: ~ 15,0 gram
– load capacity: constant 5 A, temporarily 30 A


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x 3 blades set
1 x Blade Holder Full (3 blades)
1 x 73x24 mm hard foam KOVO wheel (2 pcs)
1 x Cuadricopter F-450 Used
2 x Wheel Ø60 mm (1 ud)
1 x Oil FUCHS 1 liter
1 x DJI Phantom 3 Standard 2.7K HD videos and 12 Megapixel + Mochila
1 x Protective Nylon blade Phantom 2
1 x Rubber wheel Ø 45mm x 16mm (2pcs) axis Ø 2.1m
1 x 9x4.7 * 22x12 carbon propeller
1 x DJI MAVIC 2 Zoom
1 x DJI Phantom 3 Profesional Camara 4K NUEVA VERSION + Extra batter
1 x Rubber wheel Ø 70mm x 27mm (2pcs) axis Ø 3.6mm
1 x Tail tube RAINBOW
1 x DJI Phantom 4 + 2 Battery
1 x Carbon propellers DJI Phantom V2 (with self-locking ) Phantom 2
1 x DJI Phantom 3 Advanced Camara 2.7K VIDEO + Extra Bateria + mochi
1 x Phantom 4 Part 38 ND4 Filter
1 x Protective Nylon blade Phantom 2
1 x Wheel 28 mm
1 x Servo Controller Fibra optica
1 x Rubber wheel Ø 50mm x 18mm (2pcs) axis Ø 2.6mm
1 x Super light ∅45x9 mm axi ∅3 mm metalic core wheel
1 x Rubber wheel Ø 58mm x 21mm (2pcs) axis Ø 2.6mm
1 x VBar NEO VLink + Gyro 6.1 Express
1 x Vacuum pump P1-N
1 x 95 mm aluminium spinner.
1 x Tube holder
1 x Motor EME 35 cc
1 x Spinner Alumin. propeller pleg. 30 mm / 3,2 mm
1 x Universal Filter
1 x Spinner 115 mm GFK
1 x 51 mm aluminium spinner.
1 x Ultimate BEC 8-23 V, 5A 5V
1 x Tray for FUTABA 18 SZ
1 x 57 mm aluminium spinner.
1 x YAK 55 E 1400 mm White (Gernot Bruckmann)
1 x Spinner 159x200 mm GFK
1 x Walnut wood slat 2.0x2.0x1000 mm
1 x Aluminum Fold Prop Spinner 30 mm / 3.17 mm
1 x CDI EME 55/60 cc
1 x Pick up EME 55/60 cc
1 x 90 mm CFK long Spinner fixed by a central screw
1 x Pitts Mufflers EME 55/60 cc
1 x Trailing edge BALSA 37x8x2 mm
1 x 76 mm aluminium spinner.
1 x Tx 5.8 GHz 32 Ch 200 mW Super Mini
1 x Tygon tube 6.35 x 3.18 mm 15 m
1 x Spinner Alumin. fixed propeller 50 mm / 6,0 mm
8,616.76EUR
Manufacturers
Manufacturer Info
SETLO
SETLO Homepage
Other products
Languages
Español English
Currencies