9.00EUR

13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
[TC2237]


13 mm Self adhesive Pinking Tape, saw tooth height 0.5 mm

The covering on full size aircraft is not only glued on with dope, but is sewn to ribs and stringers to achieve a stronger covering. The distance between the knots is variable. In high stress areas such as in the propeller wash, the knots are more closely spaced. For protection all edges and sewing are covered with pinking tape.
To improve the realistic effect of a scale, or semi scale model, the sewing is a deciding factor. It is a pity that a well built model is so often all too shiny and smooth, this is very boring especially on large antique models, which then do not appear to be very scale. Our Pinking Tape is made from a highly flexible, non shrinking white self adhesive film. This tape is applied before painting the model. For those who wish to go further, the knots can be simulated with PVA glue and a hypodermic needle.
On the full size Piper Cub the Pinking Tape was 50 mm wide over the ribs, and double so wide around the wing tips and tailplane edges, the saw teeth are approximately 2 mm high. The experts use the Pinking Tape #2237 with the 0,5 mm saw teeth. The fine toothed pattern is difficult to see on the model. On the full size it is no different. If one stands at the wing tip then the saw teeth on the fuselage are not visible to the naked eye. For he who would like more readily visible saw teeth can use the Pinking Tape #2223.
The Pinking Tape #2235 is just right for the Small Tiger and the tape #2223 for the Big Tiger.


Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x 41x5,5 mm wires output (2 pcs)
1 x Nitroverdu 500 ml
1 x Universal Colour Paste deep black 250 g
1 x 1/6 Pilot "Tony"
1 x Pilot JAN 1/4 Saiplanes
1 x Plasti Dip Liquid Tape 429 ml black
1 x Hobbylite Filler, Balsa colour
1 x Civilian pilot "Joe" size 9cm (Slimline)
1 x Spannlack 1000 ml
1 x 1/10 Pilot "Jimmy"
1 x 1/6 Pilot "Garry"
1 x 1/6 Pilot "Cindy"
1 x 1/6 Pilot "John"
1 x Civilian pilot "Curt" size 9cm (Slimline)
1 x Solvent Plasti Dip 1000 ml
1 x 100 mm rods set for direction control
1 x Cable grommet Ø 3.2 mm (4 uds)
1 x Cable grommet Ø 4 mm (4 uds)
1 x Landing gear axle Ø 5 mm (2 uds)
1 x 40 mm 5-BL (rigth hydropropeller)
1 x 140 mm rods + T patellas set for direction control
1 x 28x5 mm wires output (2 pcs)
1 x 90 mm rods + T patellas set for direction control
1 x Aluminun wheel collar 3 mm Ø (4 uds)
1 x 45 mm rods set for direction control
1 x Cable grommet 9.5 mm (4 uds)
1 x Allen wheel collar M4x6
1 x 28 mm tailwheel unit
1 x 39,0 mm 3-BL M4 hydro-propeller (rigth hydropropeller)
1 x PROFI TX fastening rings
1 x 100 mm rods + T patellas set for direction control
1 x Cable grommet Ø 6.4 mm (4 uds)
1 x AL Axle Shaft 4.0x16 mm (2 uds)
1 x 31 mm M4 carbon hydro-propeller (left hydropropeller)
1 x 1000 x 2 mm steel wires
1 x 32.5 mm M4 Race propeller (left hydropropeller)
1 x Cabin latch Fox MDM1 4m (pair)
1 x 38x4,5 mm wires output (2 pcs)
1 x 40,0 mm 3-BL M4 (rigth hydropropeller)
1 x Canopy Lock V1 M3 Red (2 pcs)
1 x Canopy Latch
2 x Aluminium alloy coupler for carbon tube 6/M4
1 x 32x1,5x5 mm waterlight linkages (2 pcs)
1 x 4 mm diameter silicone tube(int)
1 x Support hands Issuer PROFI TX
1 x Glass fabric 80 g/m² (Interglas 05533, finish FK 144, twill weav
1 x Fully Threaded Steel Rod alumin 40 mm M2,5 (2 pcs)
1 x 13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x Profile ABS half cane 6.0x1000 mm
1 x ABS I Strip 10x5x1000 mm
1 x Paramotor BackPack XXS 2
1 x Ventus 1:4 set of instruments
1 x Wheel collar 2 mm Ø (4 uds)
1 x Fully Threaded Steel Rod alumin 90 mm M2,5 (2 pcs)
1 x Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x DES Servo accessory
1 x Flat Connector 4.0 mm x 1000 mm
1 x Ring 320 mm length (5 pcs)
1 x ABS Strip 1.5x6.0x1000 mm
1 x 800TVL CMOS camera for FPV
1 x PARTALL® Hi-Temp Wax, 340 g
1 x Strip 1,5x1,5x330 mm
1 x Arnes cruzado Confort de Luxe PROFI
1 x Steering arm 12 mm Ø 3 mm
1 x 60,0 mm carbon hydro-propeller (rigth hydropropeller)
1 x BALSA trip 3.0x3.0x1000 mm
1 x Profile ABS triangular 6.0x1000 mm 90º
1 x A/C quality beech plywood 600x300x0.6 mm
1 x Balsa panel 1.5x100x1000 mm
1 x Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x Hawker Hunter TopRC Model + Electric Landig gear scale + SW-140
1 x Rubber profile 6-2 mm 2M
1 x 13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x 55,0 mm 3-BL M4 (rigth hydropropeller)
1 x 2012 Aero-naut Catalog
1 x Allen wheel collar M3x3
1 x A/C quality beech plywood 600x300x4.0 mm
1 x 20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x Lead with adhesive (2 pcs)
1 x Snap pin for micro clevis (10 uds)
1 x Me-163
1 x A/C quality beech plywood 600x300x2.5 mm
1 x Camera ECO Fly Cam One V2
1 x 50,0 mm propeller (rigth propeller)
1 x 35,0 mm propeller (left propeller)
1 x Electro Propeller 9x5 (Graupner)
1 x Corporal of the marine M 1:36
1 x Fully Threaded Steel Rod Duralumin 110 mm M3 (2 pcs)
1 x Balsa panel 6.0x100x1000 mm
1 x Cross Connector 4.0 mm x 1000 mm
1 x Angle measurer
4,104.84EUR
Manufacturers
Manufacturer Info
Toni Clark
Toni Clark Homepage
Other products
Languages
Español English
Currencies