33.00EUR

8Wx2 Navigation & Strobe, 11mm Green/White
[UNDUAL110802GW]


8Wx2 Navigation & Strobe, 11mm

Powerful position and flash light in a housing. The profile light of the 11mm series is slim outside and fits optically also onto smaller models. Due to efficient LED emitter, the light has an enormous luminous power despite the compact dimension and thus it's also suitable for bigger models. The innovative, internally positioned cooling surface enables astonishingly compact dimensions with a unique slim design.

In delivery state, the profiled polycarbonate cap is simply attached. It can be varnished separately. It's highly transparent and unbreakable. The assembly of the lamp is astonishingly easy: With a simple surface mount, all you need is a slit of 3x28mm. In this way, the luminaire can be also mounted on smaller wing tips or fuselage. If desired, you can recess the luminaire up to 4mm, thus achieving an even smaller construction. The cap must be glued after the final assembly.

The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use a 4W-3S adaption cable. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Please check operation temperatures after installation.

Technical Data
Electricity: 4W GREEN and 4W WHITE reference power, 8(12)V, 2x0.7A
Beam angle: >160°
Light intensity: ~500 Lumen RED
Light intensity: ~70 Lumen GREEN
Light intensity: ~140 Lumen WHITE
Dimension assembly pin: 3x28x15mm
Dimension light cap: 11.5x42.5x10mm, up to 4mm lowerable without loss of beam angle
Total mass: 11.5x42.5x70mm
Weight: 9g (without cable)
Delivery: ready to use with 1m silicon cable and series resistor for 2S operation, resistor for 3S enclosed


Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Motor Mount for TITAN ZG45 and ZG62, length 54 mm
1 x Piston ring for ZG 20 and G240RC
1 x Carburetor for ZG45SL and ZG62/S/SL
1 x Stainless steel cable Ø 0.62 mm (10 m)
1 x Piston ring for DA-50R and DA-100
1 x Motor Mount for TITAN ZG45 and ZG62, length 72 mm
2 x 3,9 mm ZG20-ZG38 servo arm
1 x Crimping sleeves for cable 0.70 mm (10 pcs)
1 x Cylinder ZG 26SC/SLH
1 x Stainless steel cable Ø 1.3 mm (10 m)
1 x Spring Clip Ø25 mm
1 x Crimping sleeves for cable 0.85 mm (10 pcs)
1 x Spring clamp for tube Ø50 mm
1 x Cylinder for ZG20
1 x Motor Mount for TITAN ZG38/38S/38SC, length 36 mm
1 x Crimping sleeves for cable 1.3 mm (10 pcs)
1 x Motor Mount for TITAN ZG45 and ZG62, length 36 mm
1 x Piston ring for ZG 26SC/EI, ZG 26SCM ZG 26SLH and Zenoah G260RC/
1 x 13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x BOSCH spark plug cap for DA 50-R, DA 100 and DA 150
1 x Piston ring for DA-150
1 x Prop washer for ZG45SL, ZG62/S/SL and ZG74B/ZG80B
1 x 26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x Piston ring for DA-60 and DA-120
1 x Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x Quick hose connector 6-4 mm
1 x Stainless Steel Muffler D.A. 35-70
1 x DA 70 Twin Gas Engine
1 x Cilinder joint for G230RC/G260RC
1 x Metalic joint for DA-50R/DA100 cilinder/elbow
1 x Joint for DA-60 reed valve
1 x Carburetor menbrane for ZG 45SL/ ZG62/S/SL motor
1 x Cast Aluminium Intake Bend for ZG 23/26 and Zenoah 26
1 x Steel tube (L 1000 mm Ø10 mm, Ø9,7 mm)
1 x Crankcase Gasket set for ZG 74 / ZG 80
1 x Diaphragm set for ZG 74/80B, DA85/100/100L/120/200, VM170/210
1 x Spring Clip 25 mm teflon tube
1 x Spring Clip 28 mm teflon tube
1 x Gasoline big filter
1 x ZENOAH ZG 38 SC with Choke Carburettor
1 x Gasket, cylinder base for motor DA 50
1 x Silencer for ZG22, ZG23, ZG231SLH, G2D96-D
1 x Stainless Steel Bend D 20x0,6mm
1 x 4 LiPo XH>EH adapter
2,053.47EUR
Manufacturers
Manufacturer Info
UNILIHGT
UNILIHGT Homepage
Other products
Languages
Español English
Currencies