1 x | BALSA triangular 10x10x1000 mm |
1 x | BALSA triangular 6x6x1000 mm |
2 x | OBECHI sheet 2.0x3.0x1000 mm |
1 x | Pine wood slat 1.5x3.0x1000 mm |
1 x | BALSA leading edge 8x10x1000 mm |
1 x | Pine wood slat 6.0x6.0x1000 mm |
1 x | BALSA triangular 8x8x1000 mm |
3 x | Softshell Hispano Aviación |
2 x | Digital Air Speed Sensor And Pitot Tube Set |
1 x | PIX Hawk with accesories |
1 x | USB Mini Camera endoscope |
1 x | Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna |
1 x | Carbon fabric 160 g/m² (plain weave) 100 cm x 2 m |
1 x | Round Rod 2,0x1000 mm |
1 x | Premium servo extension 25cm |
1 x | Threaded coupler M2 (10 uds) |
2 x | Adapter 5,0 mm M6 for spinner 40 mm fixed propeller |
2 x | Adapter 3,2 mm M5 for spinner 30 mm fixed propeller |
1 x | Threaded coupler ALU M2 Ø 4 (2 uds) |
2 x | Adapter 3,2 mm M6 for spinner 40 mm fixed propeller |
1 x | Threaded coupler ALU M3 Ø 4 (2 uds) |
1 x | Birch plywood plate 600x300x3.0 mm |
1 x | Mahogany wood slat 1.5x1.5x1000 mm |
2 x | Beech dowels 3.0 x 1000 mm |
1 x | Pine wood slat 3.0x7.0x1000 mm |
1 x | Birch plywood plate 600x300x2.5 mm |
1 x | Beech dowels 2.0 x 1000 mm |
1 x | Pine wood slat 2.0x10.0x1000 mm |
1 x | Walnut wood slat 1.5x1.5x1000 mm |
1 x | Pine wood slat 3.0x10.0x1000 mm |
1 x | Sanyo RX Battery Eneloop 4,8 V JR |
1 x | Carbon tube (L 1000 mm, Ø1.5 mm, Ø0.7 mm) |
1 x | Smoke set "Glider" |
1 x | Remote electric ignition system |
1 x | Parachute expulsion foam |
1 x | PPM Encoder Module |
3 x | Combo lighting module with covering drop shape |
2 x | Resistor 3W 5% 2R2 |
1 x | Lock washer 3.2 mm (20 pcs) |
1 x | Unmounted aluminium pin 6x98 mm (2 pcs) |
1 x | Split pin 1x8 mm (10 uds) |
1 x | Plastic wheels 36 mm (2 pcs) |
1 x | Horn mando small (2 pcs) |
2 x | Wheel cover holder Ø 5 mm (2 uds) |
2 x | Sanyo RX Battery Eneloop 6,0 V JR |
1 x | Antonov AN2 Scale 1/6 - 3m |
1 x | Spring lock washer 4.1 mm (20 pcs) |
2 x | Spring lock washer 2.6 mm (20 pcs) |
2 x | Micro screw-lock pushrod conn snap Ø 1 mm (2 uds) |
2 x | Spring lock washer 2.1 mm (20 pcs) |
1 x | Lock washer 2.2 mm (20 pcs) |
1 x | Tapping Screw M2.2x65 (10 pcs) |
2 x | Aluminium coupler M3/2 with ball bearing (1 pcs) |
2 x | Lock washer 4.3 mm (20 pcs) |
1 x | Screw-lock pushrod conn snap Ø 1.5 mm (2 uds) |
1 x | Pulley brass 2,5/1 (2 pcs) |
1 x | Flat washer 4.3 mm (20 pcs) |
4 x | Flat washer 3.2 mm (20 pcs) |
2 x | Pin type hinge Al 3,0x50 mm demount (2 pcs) |
2 x | Lock washer 2.7 mm (20 pcs) |
1 x | Pulley brass 6/1,5 (2 pcs) |
1 x | Aluminium coupler M2/2 with ball bearing (1 pcs) |
1 x | Hexagonal Nut M3 (10 pcs) |
1 x | Flat washer 2.2 mm (20 pcs) |
2 x | Quicklock washer 1 mm (10 pcs) |
1 x | Quicklock washer 4 mm (10 pcs) |
2 x | Wheel cover holder Ø 4 mm (2 uds) |
2 x | Quicklock washer 3.5 mm (10 pcs) |
1 x | Aluminium coupler M2,5/2 with ball bearing (1 pcs) |
1 x | Plastic wheels 28 mm (2 pcs) |
1 x | Pulley brass 5/1,5 (2 pcs) |
1 x | Spring lock washer 3.1 mm (20 pcs) |
2 x | 4 mm Prop Adapter M6 |
1 x | Quicklock washer 3 mm (10 pcs) |
1 x | Tapping Screw M2.2x13 (10 pcs) |
2 x | Flat washer 1.7 mm (20 pcs) |
2 x | 5 mm Prop Adapter M8 |
1 x | Horn micro type4 Ø 0,5 (2 pcs) |
1 x | 5 mm Prop Adapter M6 |
1 x | Tapping Screw M2.9x13 (10 pcs) |
1 x | Screw M2x8 (10 pcs) |
1 x | Pan Head Screw M2x6 PH |
2 x | Flat washer 2.7 mm (20 uds)pcs) |
1 x | Screw-lock connector Ø 2 mm (2 uds) |
1 x | Quicklock washer 2 mm (10 pcs) |
1 x | Snap long M2 (10 uds) |
2 x | Wheel cover holder Ø 6 mm (2 uds) |
1 x | 3,2 mm Prop Adapter M5 |
1 x | Tapping Screw M2.9x9.5 (10 pcs) |
1 x | Pin type hinge Al 3,0x50 mm (2 pcs) |
1 x | Pan Head Screw M2x8 PH |
1 x | Wheel cover holder Ø 3 mm (2 uds) |
1 x | Screw M2x6 (10 pcs) |
1 x | Quicklock washer 2.5 mm (10 pcs) |
1 x | Plastic wheels 30 mm (2 pcs) |
1 x | ABS tube 6.0x5.0x1000 mm |
1 x | Green smoke canister 100 g |
1 x | White smoke canister 100 g |
2 x | BALSA trip 10x10x1000 mm |
1 x | Balsa panel 2.0x100x1000 mm |
1 x | Walnut wood slat 3.0x3.0x1000 mm |
1 x | Pine wood slat 2.0x2.0x1000 mm |
1 x | Birch plywood plate 600x300x1.5 mm |
1 x | Sanyo RX Battery Eneloop RX 4,8 V Futaba |
1 x | Sanyo RX Battery Eneloop 6,0 V FUT |
1 x | Shaft for A60-XS-V2 (112,5mm) |
1 x | Axle for motor A30-XL V2 |
1 x | Turbo light spinner cap white 32mm |
1 x | BALSA trip 2.0x2.0x1000 mm |
1 x | A/C quality beech plywood 1520x750x4.0 mm |
1 x | A/C quality beech plywood 600x300x5.0 mm |
1 x | A/C quality beech plywood 600x300x0.6 mm |
1 x | BALSA trip 2.0x10.0x1000 mm |
1 x | Support Antena 2.4 Ghz (2 pcs) |
1 x | Panasonic Eneloop AA 1,2 V battery 19>00 mAh |
1 x | BALSA trip 6.0x6.0x1000 mm |
1 x | Screwdriver for Torx® TX6 |
1 x | JETImodel Addcap 820 |
1 x | Battery LiFe TopFuel 3100 mAh 2s MTAG 30C |
1 x | Propadapter for motor A60-V2 |
1 x | FesEx-Uni6 System |
1 x | Screwdriver for Torx® TX8 |
1 x | A50 Motor Mount Alu complete set |
1 x | EDF Stream-Fan 110mm kv780 |
2 x | DPSI Micro SingleBat 5.9V/7.2V magnetic switch |
2 x | Fuel Dot (Silver) |
2 x | LED blink wire flashing (orange - 2pcs) |
1 x | Black 2,4 GHz antenna exit guides (2 pcs) |
2 x | Servo-V-Limiter 5.2V |
2 x | DPSI magnetic switch actuator (PCB) |
2 x | Fuel Dot (Black) |
2 x | Esc X-40-SB-Pro |
2 x | Esc master MEZON 120 Lite |
3 x | DPSI Micro - DualBat 5.9V / 7.2V JR-JR (Dual Power Supply) |
2 x | DPSI RV Mini 6 (2008) |
1 x | LED blink wire flashing (green - 2pcs) |
1 x | LED wire (rojo - 2pcs) |
1 x | Medium pin type hinge (12 uds) |
1 x | Ø 1,6 mm pin for Kwik link MPJ2160/2161 (6 pcs) |
1 x | Threaded coupler Micro M2 Ø 0,8 (10 pcs) |
1 x | 2,3 mm Prop Adapter M5 |
1 x | Brass control horn M4 short for wire (10pcs) |
1 x | 3 mm Short Prop Adapter M5 |
1 x | Excentric gearbox BB for motor 600, 3,2mm axis (1,75:1) |
1 x | |
1 x | Circlik for shaft 1.5 mm (10 pcs) |
1 x | Resistor 3W 5% OR47 |
1 x | Landing lights 18 mm (0.71in) |
2 x | Heat sink for Optotronix LEDs |
1 x | Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs) |
1 x | Battery EMCOTEC LiIon 3000 7.2v |
1 x | Esc X-70-OPTO-Pro |
2 x | DPSI Micro - RCS RV |
1 x | Esc MasterSPIN 99 Pro OPTO |
1 x | Hose clamps 0.16-0.20in, (4 pieces) |
1 x | LED wire (orange - 2pcs) |
1 x | Esc MasterSPIN 70 Pro OPTO |
1 x | Esc X-75-OPTO-Pro |
2 x | DPSI Micro - DualBat 5.9/7.2 MPX-2xMPX dual |
1 x | DPSI Ampere battery backer |
1 x | DPSI magnetic switch actuator (housing) |
1 x | ESC MEZON 115 Opto |
1 x | Filter Capacitor JR |
1 x | Optotronix X-Carrier |
2 x | DPSI 2001 RV |
2 x | DPSI Micro MPS |
1 x | OPTOTRONIX Aurora LCU |
2 x | DPSI LR-S (with push buttons) |
1 x | Esc MasterSPIN 16 Pro |
1 x | Esc MasterSPIN 80 Pro |
1 x | EWC3 40 cm wing connector |
2 x | DPSI Ampere & Voltage bundle |
2 x | DPS Switch JR/JR |
1 x | Pan head screw M2x16 PH |
1 x | Nut for mounting M3 (4 pcs) |
1 x | DYMOND VTX UBS Programming adapter |
1 x | Threaded coupler ALU Left M3 Ø 4 (2 uds) |
1 x | Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs) |
1 x | Aluminun wheel collar 5 mm Ø (4 uds) |
1 x | Cable grommet Ø 4 mm (4 uds) |
1 x | 6 mm Prop Adapter M8 |
1 x | Ball link V1 Ø7 M4/3 (6 uds) |
2 x | Emcotec SPS Magnetic Switch Actuator |
2 x | DPSI RV Mini 6 Magic |
1 x | EWC3 100 cm wing connector |
1 x | DPSI Micro-DualBat 5.9V / 7.2V MPX-JR |
1 x | Esc MasterBasic 55SB |
2 x | DPSI V-Match |
1 x | DPSI Micro - RCS |
1 x | Switch magnet for gas cap and magnet switch actuators |
1 x | Heat-conducting adhesive (2x2ml), WLK DK 4 |
1 x | EWC6 40 cm wing connector |
1 x | Esc MasterSPIN 100 Pro |
1 x | Esc MasterBasic 70SB |
1 x | Esc MasterBasic 40SB |
1 x | Cover cap drop-shaped paintable 43 mm |
1 x | DPSI RV Mini 5 (2008) |
1 x | Master MEZON 120 |
1 x | LED blink wire flashing (white - 2pcs) |
1 x | Esc MasterSPIN 75 Pro OPTO |
3 x | DPSI Micro SingleBat 5.9V/7.2V F3A Edition magnetic switch |
1 x | Fueling valve "Air" |
1 x | Esc X-30-Pro BEC |
1 x | DPSI RV Mini 6 Magic with Gas-Cap switch |
1 x | DPSI RV Mini 5 Magic |
1 x | Esc MasterSPIN 66 Pro |
1 x | Esc MasterBasic 90 Opto |
1 x | Lense for Spotlights, 20mm |
1 x | ED Position Lights wireless (Set of 3) |
1 x | Nylon threaded block M4 (2 uds) |
1 x | Pin 2,5 to cable coupler M2,5 ⌀ pin 2,5 (6 pcs) |
1 x | Pin 2,0 to cable coupler M2,0 ⌀ (6 pcs) |
1 x | Ø 1,6 mm pin for Kwik link MPJ2150/2157 (6 pcs) |
1 x | Threaded coupler ALU M2 Ø 3 (2 uds) |
1 x | Excentric gearbox for 2,0mm axis (5,0:1) |
2 x | Adapter 5,0 mm M8 |
2 x | Aluminun wheel collar 2 mm Ø (4 uds) |
2 x | Adapter 3,2 mm M8 |
1 x | Allen wheel collar M4x4 |
2 x | Adapter 4,0 mm M6 |
1 x | Aluminun wheel collar 4 mm Ø (4 uds) |
1 x | Locking cable tie 3.2x142 (uds) |
1 x | Threaded coupler Micro M2 Ø 0,8 mm (10 pcs) |
1 x | Banna gold connector 2,5 mm (100 M/F pairs) |
1 x | Allen wheel collar M3x3 |
1 x | Frontal support Speed 400/480 |
1 x | Excentric gearbox for 2,3mm axis (4,1:1) |
1 x | Couple M4 for wire (10 pcs) |
1 x | Aluminun wheel collar 3.5 mm Ø (4 uds) |
1 x | Aluminium alloy coupler for carbon tube 6/M4 |
1 x | Brass control horn M2 large for wire (2pcs) |
1 x | Adapter 4,0 mm M8 |
1 x | 2,3 mm Prop Drive Günther M4 |
1 x | Cable grommet 9.5 mm (4 uds) |
1 x | Locking cable tie 2.5x100 (uds) |
1 x | 2 mm Prop Adapter M5 |
1 x | Threaded coupler ALU M2,5 Ø 4 (2 uds) |
1 x | Cierre cabina aluminio Ø4, I=10 mm |
1 x | Brass control horn M2 long for wire (10pcs) |
1 x | Threaded coupler M2,5 Ø 2 mm (10 pcs) |
1 x | Cable grommet Ø 6.4 mm (4 uds) |
|
11,898.41EUR |